ZZIPP ZZEPHYRUS412 Automation For Sliding Gate User Manual
- June 15, 2024
- ZZiPP
Table of Contents
ZZIPP ZZEPHYRUS412 Automation For Sliding Gate
Thanks for purchasing this ZZIPP product, please read this instruction carefully to understand how to operate the product correctly. Please store this instruction in a safe place after reading as a reference in the future.
SAFETY INSTRUCTIONS
To reduce the risk of fire and electric shock, do not expose the appliance to moisture and direct contact with liquids.
-
This symbol, wherever used,alerts you to the presence of un-isulated and dangerous voltages within the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock.
-
This symbol, wherever used, alerts you to important operating and mainte-nance instructions. Please read.
-
WARNING Describes precautions that should be observed to prevent the possibility of death or injury to the user.
-
CAUTION Describes precautions that should be observed to prevent damage to the product.
-
Power Supply Ensure that the mains source voltage (AC outlet) matches the voltage rating of the product. Failure to do so could result in damage to the product and possibly the user. Unplug the product before electrical storms occur and when unused for long periods of time to reduce the risk of electric shock or fire.
-
External Connection Always use proper ready-made insulated mains cabling (power cord). Failure to do so could result in shock or fire. If in doubt, seek advice from a registered electrician.
-
Do not Remove Any Cover Within the product are areas where high voltages may bepresent. To reduce the risk of electric shock do not remove any covers unless the AC mains power cord is removed.
Covers should be removed by qualified service personnel only. No user serviciable parts inside. -
Fuse To prevent fire an damage to the product, use only the recommended fuse type as indicated in this manual. Do not short-circuit the fuse holder. Before replacing fuse, make sure that the product is OFF and disconnected from the AC outlet.
-
Protective Ground Before turning the product ON, make sure that it is connected to Ground. This is to prevent the risk of electric shock. Never cut internal or external Ground wires. Likewise, never remove Ground wiring from the Protective Ground Terminal. Operating Conditions Always install in accordance with the manufacturer´s instructions. To avoid the risk of electrtic shock and damage, do not subject the product to any liquid/rain or moisture. Do not use this product when in close proximity to water.
-
Do not install this product near any direct heat source. Do not block areas of ventilation.
FRONT PANEL
- BT VOL – Bluetooth mode Volume Control.
- TWS BUTTON – Press once to enter True Wireless Stereo Bluetooth mode.
- ON/OFF BUTTON – Press once to connect a Bluetooth device or disconnect a paired Bluetooth device.
- DSP PREST – There are three preset mode: FLAT – DJ – VOICE.
- INDICATOR LIGHT – Limit / Signal / Power.
- CH1, CH2 VOL – CH1 Volume Control / CH2 Volume Control.
- CH1, CH2 INPUT – Balanced Combo XLR/Jack input for getting signals from mixers or preamplifiers.
- MIC/LINE SELECT BUTTON – Press down for Line level signal , press up for Microphone level signal.
- SAT VOL – Satellite Volume Control.
- SUB VOL – Subwoofer Volume Control.
- LINE OUT – Balanced XLR connectors connected in parallel to the inputs to connect subwoofer.
TWS PAIR
TWS sends the same Bluetooth source to 2 speakers in wireless mode.
Pairing 2 speakers:
- Turn on the first speaker and press the bluetooth button to activate the function.
- Turn on Bluetooth on the source (smartphone, tablet, PC, etc.) and connect to the speaker.
- Turn on the second speaker and press the bluetooth button.
- After a few seconds, the two speakers are automatically paired, so if you play a signal from the Bluetooth source, both speakers will start playing.
SPECIFICATIONS
Type | 1pc column + 1pc 12’’ subwoofer |
---|---|
Frequency Response (-6dB) | 45 Hz – 20 kHz |
Max. SPL (1m, free space) | 126 dB |
Power Output (RMS) | 400W+200W |
Transducer HF | 8pcs * 3” driver, 20mm voice coil |
Transducer LF | 12” subwoofer, 2.5” voice coil |
Amplifier | Class-D amplifier |
DSP Module | DSP-100, 96 kHz, 24-bit DSP processor |
Protection | Short circuit overheating, over-current |
Controls | Power On / Off switch, main level, DSP modes switch |
Audio Input / Output | 2 x Combo XLR/Jack input, 1 x XLR output |
Power Input / Output | Powercon |
Power Supply | 230V 50/60 Hz |
Enclosure | ABS/PP Plastic |
Contact Information
imported and distributed by:
ZZIPP Group S.p.A.
- Via Caldevigo 23/d, 35042 Este (PD)
- 0429 617 888
- info@zzippgroup.com
- zzippgroup.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>