REDCAT PAGANI EPX 1-10 4WD Electric-Powered On-Road Car Instruction Manual

June 12, 2024
REDCAT

REDCAT PAGANI EPX 1-10 4WD Electric-Powered On-Road Car Instruction Manual

Highlights:

  • 4 wheel drive system
  • Ready assemble ready to run
  • Belt drive (Bando belts from Japan)
  • Full ball bearing
  • New designed , the body can change any color you love .

⚠ SAFETY PRECAUTIONS

  • This radio controlled racing truck is not a toy!
  • This high-performance R/C vehicle is recommended for ages 14 and older.
  • First-time builders should seek the advice of experienced modellers before commencing assembly.
  • Take enough safety precautions prior to operating this vehicle.
  • You are responsible for this R/C vehicle’s assembly and safe operation!

Required equipment for operation

1. Tools required for building and maintenance:

WARNING!
Do not use a power screw driver to install screws into nylon or plastic materials. The fast locking may heat up the screws being installed that may break the Molded parts or strip the threads during installation.

2.Additional items needed for operation:

IMPORTANT!
Check all the screws are tight before playing the vehicle!
Use thread lock on all screws that work loose.

Please read the instruction carefully before starting the assembly.

  1. Please assemble and install this car without children’s reach. As it includes small and sharp parts.
  2. Do not run the car on public streets or highways. As it might cause serious accidents, personal injuries and property damage etc.
  3. During the middle of racing and after operation, the engine and exhaust will become HOT. Therefore please do not touch them before cooling down.
  4. Please make sure everyone is using different frequencies while racing the car in the same area.

2.4GHz radio instructions

Special symbols
Please pay attention to the following symbols, and read them carefully.

⚠ Danger: If the operator does not operate according to the instructions, it may lead to serious injuries, even mortal danger.
⚠Warning: If the operator does not operate according to the instructions, it may lead to serious injuries, even mortal danger.
⚠ Attention: If the operator does not operate according to the instructions, it may lead to Ennio. serious injuries, even mortal danger. but generally it will not cause serious injuries to the operator.

Safety guidelines
Don’t drive the truck at night, bad weather such as rainy or thundering days. It will interfere the transmitter signal. Thereby it will cause out of control and unexpected accident.

Before you drive, please make sure the movement of servo corresponds with the direction of joysticks. If inconsistent, please adjust before drive.

You need to turn the throttle channel(ch2) and inching switch to the lowest before use. Then switch on the transmitter power, finally connect the receiver.

The sequence to shutdown is to turn off the receiver power first, and then the transmitter power.

If the above operations are reversed, it might lead to out of control and cause accident.

Battery charging
If your transmitter, receiver use a nickel-cadmium, nickel-metal hydride rechargeable battery, you have to check it before use. If lack of electricity, it could cause inadequate control or out of control, resulting in accident. So please charge it immediately when the battery power is low.

Transmitter specifications

Channels: 2 channels
Model Type: Car /boat
RF Power: Less than 20dbm
Modulation: GFSK
Code Type: Digital
Sensitivity: 1024
Low Voltage Warning: Yes (less than 9V)
DSC Port: Yes (3. 5mm)
Charger Port: Yes
Power: 12vdc(1. 5AA8)
Weight: 328g
ANT Length: 26mm
Size: 159
99*315mm
Color: Black
Certificate: CE FCC

Note:
Place the antenna of the receiver vertically, and do not have contact with metal component. (See Figure1)

Binding:
The transmitter and receiver should be already bound by the factory by default.

  1. Install batteries into the transmitter and shut it down.
  2. Insert the bind cable on to the b connect the receiver battery to the VCC port on the receiver .The two LEDs on the receiver should flash rapidly, indicating the receiver is in binding state .
  3. Press and hold the bind button on the transmitter, and then turn on the transmitter.
  4. The LED on the receiver should stop flashing when the binding process completed (about 5 second)
  5. Release the bind button on the transmitter, remove the bind cable from the receiver.
  6. Install the servo and then test.
  7. If the test succeeds, then remove the power supply from the VCC port.
  8. The binding process completed.

Turn On:

  1. Turn on the transmitter. Power on
  2. Connect the power supply of the receiver.
  3. Receiver LED light should turn solid.
  4. Ready to use.

Shut Down:

  1. Disconnect the receiver’s power supply.
  2. Turn off the transmitter.

Transmitter Functions:

Brushed Version Parts List

PAGANI EPX

REDCAT PAGANI EPX 1-10 4WD Electric-Powered On-Road Car Instruction Manual -
Pagani Epx

PAGANI EPX PRO

Precautions and Warnings for Use and Handling of Lithium Polymer Battery

Preface
In order to get the optimum performance and reliable safety, consumers shall read and take the following instructions and precautions when use and handle the Lithium Polymer (Li-Po) batteries.

  1. Charging
    1-1 Charging current should not be more than the maximum charge current specified in the Product Specification (normally 0.5C-1.0C or lower). Charging with higher current may damage the cell or even lead to safety problem, e.g. overheating or leakage.
    1-2 Charging voltage shall not be more than that specified in the Product Specification (4.2V/cell). 4.25V is the maximum charging voltage for each cell. Never charge the battery in series and be sure that each single cell has a separated charging circuit with a max. charging voltage of 4.25V.Or the battery may be overcharged, and lead to fire or explosion.
    The user is fully responsible to the result of misusing the battery.
    1-3 Charging temperature: The cell should be charged within the range of temperatures specified in the Product Specification. Stop charging immediately when the surface temperature of the battery is over 50°C.
    1-4 Reverse charging: Please make sure the polarities of cells are connected properly before charging. Reverse charging is strictly prohibited. Reverse charging cannot charge the cells but will deteriorate their charging/discharging and safety characteristics, or even lead to fire or explosion.

  2. Discharging
    2-1 Discharging current: The cell shall be discharged at the current no more than the maximum discharging current specified in the Product Specification. Over current discharging may damage the battery and cause over-heat.
    2-2 Operation temperature: Use the battery within the temperature range specified in the Product Specification. Stop using when temperature is over 70°C.
    2-3 Over-discharging: Over-discharging will deteriorate the cell’ s performance and characteristics. Do not over-discharge a battery below 2.75V/cell.

  3. Storage
    If you intend to keep the battery for a long time (3 months or longer), it is strongly recommended that the battery shall be stored under the environment with temperature 10-25°C, low humidity and without corrosive gas. The battery should be charged every six months to ensure that each cell’ s storage voltage is 3.6~3.9V.

Others

The aluminum packing foil is very soft that it will be easily left scratches. Please do not hit the cell with any sharp edge parts.
Don’ t fall, hit or bend the battery. It may cause fire or explosion.
Short circuit the battery is strictly prohibited, it may damage the battery seriously.
Never disassemble the battery. It may cause fire.
Never dispose of the battery in fire. It is very dangerous and strictly prohibited.
To place the battery into liquid such as water is strictly prohibited.
Always remove battery from car when charging. Charging the battery in a car is forbidden and is dangerous.
Avoid vibration, shock or extruding the battery. Handle carefully when moving it.

Redcat Racing
http://www.redcatracing.com

PRINTED IN CHINA NOT RESPONSIBLE FOR TYPOGRAPHICAL ERRORS

Documents / Resources

| REDCAT PAGANI EPX 1-10 4WD Electric-Powered On-Road Car [pdf] Instruction Manual
PAGANI EPX, PAGANI EPX PRO, PAGANI EPX 1-10 4WD Electric-Powered On-Road Car, PAGANI EPX 1-10, 4WD Electric-Powered On-Road Car, Electric-Powered On-Road Car, On-Road Car, Car
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals