REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit Owner’s Manual

June 7, 2024
REDCAT

REDCAT RER13192 Racing 13192 1964 Impala Clear Body
Kit

Link to the most recent version of this manual with exploded views and parts lists: www.redcatracing.com/pages/manuals
Chevrolet, Impala, all related Emblems, and vehicle body designs are General Motors Trademarks used under license to Redcat Racing.
MAN-SIXTY-FOUR-CLEAR-BODY-KIT-20-11-20

INCLUDED

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit -
Inclued

REQUIRED

Clear Dish Soap – To wash clear body parts prior to painting.
Polycarbonate Spray Paint – To paint the body and interior. Must be suitable for clear polycarbonate bodies.
3M VHB Double-Sided Tape – To assemble the body. We highly recommend using 3M VHB (.375 inch or.5 inches wide) double-sided tape.
Hobby Knife – For trimming tape as well as body fitment.
Philips Head Screwdriver – For securing chrome plastic pieces and body mounts.
1.5 mm Hex Driver – For securing the steering wheel and column.
Glue – E6000, Hot Glue or Instant CA for securing the chrome rings to the back of the chrome plastic pieces.
Hair Dryer or Heat Gun – For smoothing out the chrome trim stickers.
Side Cutters – For removing the chrome plastic pieces from the parts trees.
2mm Drill Bit – For drilling a hole through the front and rear panels

PAINT PREP

  1. Using liquid dish soap, wash and dry the clear body components to remove oils that may have been left behind from production.
    NOTE: There is a clear film on the outside of each clear body panel. DO NOT REMOVE THIS CLEAR FILM. The clear film is to protect the outside of the body from paint overspray. Only remove the film AFTER the painting has been completed and you are ready for assembly. REDCAT RER13192 Racing 13192 1964
Impala Clear Body Kit - Paint

  2. Mask the windows and headlights with the included precut yellow paint masks. Align each point as shown to position the masks.
    NOTE: The masks must go on the INSIDE of the body.
    NOTE: Try not to touch the inside of the body. The oils from your skin may negatively affect the paint. REDCAT RER13192 Racing 13192 1964 Impala Clear
Body Kit - Paint 2NOTE : If doing a custom paint job, with two or more colors, apply the additional masking AFTER all included window masks have been applied.

PAINTING

It is important to only use paint designed for clear polycarbonate bodies. Paints that do not specify use on clear polycarbonate bodies will result in a bad paint job that will eventually crack and flake off.
Spray paint the body panels from the inside. It is best to apply several light coats of each color.
NOTE: Heavy coats of paint may result in paint seeping beneath the masking tape.

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - Pain
3t

BODY ASSEMBLY

Allow the paint to completely dry before assembling the body.

  1. Peel off the protective film and remove all masks from all painted parts.

  2. Apply 3M VHB double-sided tape to the marked areas of the main body (see image below) and peel off the tape’s protective film on the right side of the main body only.

  3. Carefully align the right fender with the main body. Start behind the rear window (A), being careful not to let any other part of the fender touch the main body.

  4. Align the rear of the fender with the main body (B). Align (C) and (D) to the main body and press firmly in place. Support the taped areas from beneath with your fingers as you press the fender in place.

  5. Repeat this process for the left fender.REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - Body 4REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - Body 5

  6. Apply double-sided tape to the tops and sides of the rear panel (see below). Only remove the tape’s protective backing from the top of the panel and align it to the underside of the hood.
    Press firmly to adhere.REDCAT RER13192 Racing 13192 1964 Impala Clear Body
Kit - Body 6

  7. With the rear panel stuck firmly in place, remove the tape’s protective backing from the right side of the rear panel while holding the corner of the right fender away from the rear panel. (see image to the right)

  8. Squeeze the corner of the rear fender firmly into place and do the same for the left side.

  9. Repeat this process for the front panel.REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - Body 9

NOTE : While all of the body pieces are trimmed from the factory, There may be some areas that require additional trimming for proper fitment.REDCAT
RER13192 Racing 13192 1964 Impala Clear Body Kit - Body
9.1

NOTE: Insert a 2mm drill bit into the front-most hole, in the center of the hood, and drill through the front panel as shown. Repeat this step for the rear panel. If using a rotary tool, use the slowest setting.

CHROME DECAL INSTALLATION

Using the diagram below for placement, apply one chrome trim sticker at a time.
NOTE: Be careful when handling the chrome trim stickers to ensure you don’t damage the chrome foil.

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit -
ChromeREDCAT RER13192
Racing 13192 1964 Impala Clear Body Kit - Chrome 2

Use a hairdryer or heat gun to set the chrome stickers in place.
CAUTION: Overheating the stickers will cause them to burn and shrivel up. Apply the minimum amount of heat needed to mold the stickers around the contours of the body.

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - Chrome
3

STICKER PLACEMENT

See below for sticker placement.
NOTE: The radiator sticker must be adhered to before installing the plastic grill.

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit -
StickerREDCAT RER13192
Racing 13192 1964 Impala Clear Body Kit -Sticker 1

INTERIOR STICKER PLACEMENT

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - Sticker
2

CHROME PLASTIC PLACEMENT

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - chorme
3REDCAT
RER13192 Racing 13192 1964 Impala Clear Body Kit - Sticker
4

NOTE: Be sure to install the clear marker light lenses before installing the light buckets onto the front bumper.
The two marker lenses should be painted translucent amber.
NOTE: The rear body mount is screwed into the rear bumper with three screws. The front body mount is fastened to the front bumper the same way.
Note the direction of the posts.

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - crome
5

Use a drop of instant glue to secure the mirror lens to the mounting post.
Use a drop of instant glue, a dab of E6000, or a hot glue gun to secure the chrome rings, to the backside of the chrome plastic posts, on the trim pieces.

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - chorme
6

STEERING WHEEL INSTALLATION

  1. Locate the steering wheel, steering column, and long screw.
  2. Assemble the steering wheel and steering column as shown below.REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - Installation
  3. Locate the small hole in the interior panel dashboard.
  4. Insert the screw into the hole from the underside of the interior panel and screw it into the steering assemblyREDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit - Installation 4

REDCAT RER13192 Racing 13192 1964 Impala Clear Body Kit -
REDCATwww.redcatracing.com
Follow us on social media
Take a photo, create a video, post and share your Redcat experience.

Stay up to date on the latest Redcat news, products, and creative content. While these profiles are not customer service channels, you might find that one of our subject experts or another member of the community is able to assist you. If you have an issue or need technical and/or product support, please reach out to Redcat directly through our website.

| https://www.redcatracing.com
https://www.facebook.com/RedcatRacing
https://www.instagram.com/Redcatracing/
https://www.youtube.com/RedcatRacing
https://www.twitter.com/RedcatRacing
https://www.pinterest.com/Redcatracing/
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals