TELTONIKA RUT360100100 Industrial DIN Rail Router User Guide

: June 12, 2024
: teltonika

Table of Contents

| Networks
RUT360

| Networks

RUT360

Quick Start Guide v1.3

Wiki knowledge base
https://wiki.teltonika-networks.com/

FRONT VIEW

TELTONIKA RUT360100100 Industrial DIN Rail Router A0

Mobile network type LEDs
Mobile signal strength indication LEDs
Ethernet ports
WAN LED
LAN LED
SIM holder
Power LED
Power socket

BACK VIEW

TELTONIKA RUT360100100 Industrial DIN Rail Router A1

WiFi antenna connector
Mobile MAIN antenna connector
Mobile AUX antenna connector
Reset button

POWER SOCKET PINOUT

Power / Red wire
Input / Output / Green wire
Ground / Black wire
Input / Output / White wire

I/O (PIN 3 and 4): Configurable digital Input/ Output pins. Open collector output max output 30 V, 300 mA or Digital input where 0-6 V detected as logic low and 8-30 V – logic high.

HARDWARE INSTALLATION

Push the SIM holder button with the SIM needle.
Pull out the SIM holder.
Insert your SIM card into the SIM holder.
Slide the SIM holder back into the router.
Attach Mobile and WiFi antennas.
Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to LAN port.

To enter the router’s Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
Use login information shown in image A when prompted for authentication.
After you login, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory and you will not be able to interact with the router’s Web UI before you change the password.
When you change the router’s password, the Configuration Wizard will start. The Configuration Wizard is a tool used to setup some of the router’s main operating parameters.
Go to Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

A.

B.

MOBILE|

-50 dBm

---|---
Data connection |

Connected

State|

Registered (home); OPERATOR; 4G (LTE)

SIM card slot in use|

Ready

Bytes received/sent|

348.7 KB / 223.5 KB

TECHNICAL INFORMATION

Radio specifications

RF technologies | 3G, 4G, WiFi
Max RF power | 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi

**Bundled accessories specifications***

Power adapter | Input: 0.45 A@100-240 VAC, Output: 12 VDC, 1 A, 4 pin plug
Mobile antenna | 698-960/1710-2690 MHz, 50 0, VSWR<3, gain 4 dBi, omnidirectional, SMA male connector
WiFi antenna | 2400-2483.5 MHz, 50 0, VSWR<2, gain 5 dBi, omnidirectional, RP-SMA male connector

*Order code dependent.
**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

SAFETY INFORMATION

RUT360 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.

Hereby, TELTONIKA NETWORKS declares that this RUT360 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following
Internet address: https://wiki.teltonika-networks.com/view/RUT360_CE/RED

Instruction Manual: Connect the power adapter to turn on the device. Open 192.168.1.1 in your web browser to configure it. More information on https://wiki.teltonika-networks.com/

This sign means that all used electronic and electric equipment should not be mixed with general household waste.

This sign means that product meets the requirements of the applicable EU directives.