KONG TRIMMER+ Positioning System Instruction Manual

KONG TRIMMER+ Positioning System Instruction Manual

INSPECTION SHEET

MASTER TEXT in English

• – GENERAL INFORMATION

  • The information provided by the manufacturer (hereinafter information) must be read and well understood by the user before using the
  • All our devices are tested / checked piece by piece in accordance to the procedures of the Quality System certified according to the UNI EN ISO 9001
  • Personal protective equipment is certified by the notified body reported in the specific instructions of the device in accordance with Annex V of the Regulation (EU) 2016/425. If Category III PPE, they are subject to surveillance of production in accordance with Annex VIII of the Regulation (EU) 2016/425 by the notified body whose accreditation number is marked on the
  • Personal use of the device is recommended to monitor the degree of the device and to maintain it
  • Check that the device has been supplied intact, in the original packaging and with its For devices sold in different countries from the destination of origin, the distributor shall verify and supply the translation of this information.
  • This device can be used in combination with other devices when compatible with relevant manufacturer
  • Important
  • Avoid exposing the device to sources of heat and contact with substances chemical. Reduce direct exposure to the sun, in particular for textile and plastic Low temperatures and humidity can facilitate the formation of ice, make it difficult to make connections, reduce flexibility, as well as increasing the risk of breakage, cutting and abrasion.
  • The position of the anchor is fundamental for arresting a fall safely: carefully assess the clearance under the user, the height of a potential fall, the stretch of the line/rope, the deployment of an eventual energy absorber, the height of the user, and the “pendulum” effect, in order to avoid any possible obstacle (eg the ground, the rubbing, abrasions, ).
  • The minimum strength of the anchor points shall be at least 12 kN, both made on natural and artificial elements. The evaluation of those made on natural elements (rock, plants, etc.) are only possible in an empirical way, so it shall be carried out by a trained and experienced person. For those made on elements artificial (metal, concrete, etc.), the evaluation can be carried out scientifically, therefore it shall be carried out by a trained and authorized
  • Warning
  • Prolonged suspension, especially if inert, can cause damage irreversible and even
  • It is absolutely forbidden to modify and / or repair the device, outside than what is prescribed in this
  • If the user has the slightest doubt about the efficiency of the device shall replace it immediately, particularly after using it to stop a
  • This device shall only be used by users medically fit, trained (and educated) for use or under direct control of trainers /
  • Rock and ice climbing, descents and abseils, the “via ferrata”, speleology and caving, ski-mountaineering, canyoning, exploration, rescue, tree climbing and work at height are all high-risk activities that may involve even fatal accidents. The user assumes all risks arising from the practice of these activities and the use of all our
  • Laboratory tests, checks, inspections, information and standards do not always succeed to reproduce the practice, so the results obtained in real life conditions of use of the device may sometimes differ significantly. The best indications are provided by the continuous use and practice under the supervision of competent / experienced / qualified
  • This information concerns the description of the features, performances, assembly, disassembly, maintenance, conservation, disinfection, of the device. Even if they contain some suggestions for use, should not be considered an operating manual in real situations (as well as a maintenance manual of a car does not teach driving and does not replace driving school).
  • – WORK AT HEIGHT
  • Additional information for individual fall protection systems in the context of work at
  • For safety purposes, in these systems is essential to:
  • carry out risk assessment and ensure that the entire system, of which this device is only one part, is both reliable and safe;
  • prepare a rescue plan to deal with any emergencies that could arise while using the device;
  • position the anchor device or the anchor point as high as possible;
  • minimize the height of potential falls;
  • use devices that are suitable for the purpose and
  • Important: in a fall arrest system it is mandatory to use a full body harness being the only device suitable for this use and this device must comply with current
  • – STORAGE AND MAINTENANCE
  • Store the device in a dry place (relative humidity 40-90%), fresh (temperature 5-30 ° C) and dark, chemically neutral (avoid absolutely saline and / or acid environments), away from sharp edges, corrosive substances or other possible prejudicial
  • Transport the device considering the precautions foreseen for storage and limit direct exposure to sunlight and
  • Maintain the device as follows:
  • wash frequently with warm drinking water (30 ° C), possibly with the addition of a neutral detergent;
  • rinse and leave to dry, avoiding spinning and direct exposure to the sun;
  • only for metal components, lubricate the moving parts with silicone-based oil after drying, avoiding contact with textile
  • If necessary, disinfect by soaking the device for an hour in warm water with sodium hypochlorite diluted 1% (bleach). Rinse thoroughly with drinking water, and, without spinning, leave to dry without exposure direct to the Avoid autoclaving the textile devices.
  • – CONTROLS AND INSPECTIONS
  • User safety depends on continuous efficiency, integrity and strength of the device, which it is necessary to monitor through the controls and the prescribed
  • Before and after use the user must carry out all the checks described in specific information, and in particular make sure that the device is:
  • in optimal conditions and that works properly;
  • suitable for use in accordance with these instructions (any other use is considered non-compliant and therefore potentially dangerous).
  • Except for more restrictive legal requirements, inspections of Category III devices shall be carried out:
  • at least every 12 months starting from the first use;

• the time interval between inspections can be reduced according to the type, the frequency and the environment of use;

• by a competent person (therefore formed and authorized by the manufacturer, eg a “KONG PPE Inspector”) in strict compliance with the manufacturer’s

  • The results of periodic inspections must be recorded on the form inspection of the device or on a designated 5 – DEVICE LIFE
  • The lifespan of the metal components is indefinable, theoretically unlimited, while those affected by aging report the expiration date over which the device shall be This provided that:

• the device was not used to stop a fall;

• the methods of use comply with the information in this information;

• storage and maintenance are carried out as described in point 3;

• the results of pre -use and post-use controls are positive;

• the results of periodic inspections are positive;

• the device is used correctly not exceeding the marked MBS of 1/4 for metal devices or of 1/10 polymer/mixed

  • Discard the devices used to stop a fall or which have not passed pre-use or post-use controls, or periodic
  • Improper use, deformations, falls, wear, chemical contamination, exposure to temperatures below -30 ° C or above + 50 ° C for textile/plastic parts/devices and + 120 ° C (eg autoclave) for metal devices, are some examples of other causes that can reduce, limit and terminate the life of the

• – LAW OBLIGATIONS

  • Professional, recreational and competition activities are often regulated by specific laws or regulations that may impose limits and/or requirements for the use of PPE and the preparation of safety systems, of which PPE are
  • It is duty of the user to know and apply these laws which could provide for limits different from those reported in this 7 – GUARANTEE
  • The manufacturer guarantees the conformity of the device to the regulations in force at the time of production. The warranty for defects is limited to the defects of raw materials and manufacturing, does not include normal wear and tear, oxidation or damage caused by improper use and/or in competitions (where they are not specifically accepted by the organization of the same), from incorrect maintenance, transport, storage or storage, The warranty expires immediately if the device is modified or tampered with.
  • The validity corresponds to the legal guarantee of the country in which the device was sold, starting from the date of sale of the new After this period no claim can be made against the manufacturer.
  • Any request for repair or replacement under warranty must be accompanied by a proof of If the defect is recognized, the manufacturer will commits to repair or, at its discretion, to replace or refund the device. In no case the manufacturer’s liability extends beyond the invoice price of the device.

8 – SPECIFIC INFORMATION

The Category III Personal Protective Equipment 289.S00 is:

• a lanyard with a length adjustment device used to connect a body holding device to an anchor point as a means of support for restraint;
• a lanyard with a length adjustment device used to connect a body holding device to an anchor point, or to a structure by encircling it, as a mean of support for work positioning;
• part of a system of protection and/or prevention of the impact created by falls from a height;
• certified according to standard EN358:2018.

Fig. 1 – Connections – Use a proper connector to attach the device at the anchor point or the harness.
Fig. 2 – Length adjustment – To shorten the length of the device simply pull the free end of the rope (C). To increase length, push the lever of the adjuster (B) and pull by the loop (A).
Fig. 3 – Above the harness – The lanyard anchor/structure must always be above the attachment point of the harness. Fig. 4 – Examples of use – Always keep the device taut!

Compatibility – This device has been designed to be used with:

• connectors according to EN362;
• anchor devices according to EN795;
• harnesses according to EN358, and/or

Check before and after use – Before and after use, make sure that the device is in an efficient condition and that it is working properly, in particular, check that:

• is suitable for the use you intend to make of it;
• has not been mechanically deformed;
• shows no sign of UV contamination, corrosion and oxidation;
• after moving the protection the stitching of the loop (A) are intact and there are no cut or loose threads;
• the adjuster (B) works as described and is free from debris;
• rope (C) does not have cuts, burns, chemical residues, excessive hair, wear, in particular check the areas in contact with metal components;
• markings are still

Important:

• the use of improper combinations of PPEs may affect or interfere with their safe function;
• this device must be connected only to harness attachment points suitable for work positioning or restrain, according to the system to be composed;
• when using a work positioning systems it is essential to consider the need of using second safety system, g. a fall arrest system, and to keep the anchor point at or above the waist level;
• PPEs composing the fall prevention/protection system must properly be selected according to the weight of the user and the condition of application, paying specially attention to energy absorbing

Warning:

• during use this device must be always kept taut;
• this device is not suitable for fall arrest purposes;
• always keep the anchor point above the attachment point of the

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>