KONG IT 864.010 10 Holes Plate Instruction Manual
- June 1, 2024
- KONG IT
Table of Contents
KONG IT 864.010 10 Holes Plate
Product Information
Specifications
- Category III Personal Protective Equipment 864.010 RALLY and 864.011 RALLY BENT are multi-anchor rigging plates, compliant with UIAA 130:2021 V1 and relevant points of EN 354:2010, EN 365:2004, EN 795:2012 and Regulation (EU) 2016/425.
- Suitable for use in mountaineering, including rock climbing, protection/prevention of falls from height, creating prevention and fall arrest systems, retention, work positioning, and rope access systems.
- The device complies with clause 4.2.1.1 of CEN/TS 16415:2013 for simultaneous use by 5 users.
Product Usage Instructions
Important Safety Considerations
- Carefully assess the suitability of the structure and anchor point about the load transmitted (max 36 kN) by the device during use.
- When using this device as part of a fall-arresting system, use suitable equipment like energy absorbers to reduce impact forces created during a fall arrest.
Correct Positioning and Use
Examples of correct positioning using textile material should be followed as shown in Figure 2. Refer to Figure 3 for an example of correct use. Be aware of the weakest direction as illustrated in Figure 3b.
Incorrect Positioning Warning
- Avoid incorrect and dangerous positioning as shown in Figure 4.
- Before use, conduct suspension tests in a safe environment to ensure proper device functionality.
Compatibility
The rigging plates RALLY and RALLY BENT are designed for connection with specific metal and textile devices. Ensure compatibility with connectors, ropes, slings, lanyards, energy absorbers, and fall-arresting devices according to EN standards.
Checks Before and After Use
Before each use, ensure the device is efficient and in proper working condition. Check for cracks, corrosion, mechanical deformation, and aesthetic wear. Verify that all markings are legible.
FAQ
Q: How do I know if the device is suitable for my intended use?
- A: Before each use, carefully assess the structure and anchor point concerning the load transmitted by the device. Ensure it aligns with the specifications provided.
Q: Can the rigging plates be used for activities other than mountaineering?
- A: The rigging plates are primarily designed for mountaineering activities but can also be used for fall arrest systems, work positioning, and rope access systems within their specified limits and guidelines.
NOMENCLATURE
864.011 RALLYBENT
- A Connection eyelets
SPECIFIC INFORMATION
- Category III Personal Protective Equipment 864.010 RALLY and 864.011 RALLY BENT are multi-anchor rigging plates, compliant with UIAA 130:2021
- V1 and relevant points of EN 354:2010, EN 365:2004, EN 795:2012, and Regulation (EU) 2016/425 suitable for:
- use in mountaineering, including rock climbing;
- protection/prevention of falls from height;
- creating prevention and fall arrest systems, retention, work positioning, and rope access systems;
- The device also complies with clause 4.2.1.1 of CEN/TS 16415:2013 for simultaneous use by 5 users: this type of utilization is to be considered outside the scope of Regulation (EU) 2016/425.
Important:
- carefully assess the suitability of the structure and the anchor point, concerning the load transmitted (max 36 kN) by the device during use and the corresponding direction of application (fig.1);
- when you use this device as part of a fall-arresting system, you must use suitable equipment (like energy absorbers) to reduce impact forces that may be created when a fall is arrested.
Use
- Examples of correct positioning, using also textile material (fig.2). Example of correct use (fig.3).
Weakest direction (fig.3b).
- Examples of incorrect and dangerous positioning (fig.4).
- Before use, in a completely safe position, carry out suspension tests to ensure that the device is working properly.
Warning
- Devices inserted in the connection eyelets (A):
- must be free to move and to position themselves in the foreseeable direction of load application;
- must not get into contact with each other.
Compatibility
- The rigging plates RALLY and RALLY BENT have been designed for connection with the following metal and textile devices whose attachment point can be opened or passed through the connection eyelets (A):
- connectors (EN 362, EN 12275);
- ropes (EN 892, EN 1891);
- slings (EN 566);
- lanyards (EN 354);
- energy absorbers (EN 958, EN 355);
- fall arresting devices (EN 353-1, EN 353-2, EN 360, EN 12841/A).
Checks before and after use
- Before and after use, make sure that the device is in an efficient condition and that it works properly, in particular, check that:
- it is suitable for the intended use;
- it is free of cracks, corrosion, and mechanical deformation and any wear and tear is only aesthetic;
- markings are legible.
Certification
- This device has been certified by the notified body No. 2008 Dolomiticert S.c.a.r.l. Zona Industriale Villanova 7/a – 32013 Longarone BL – Italy
Read and always follow the information supplied by the manufacturer
- Download the declaration of conformity at: www.kong.it/conformity
- Please calculate the lifespan of the device according to: www.kong.it/en/life/
MARKINGS
- UIAA 130:2021 V1 Conformity to the relative UIAA standard
- MAX 36 kN
- Maximum load
- KONG S.p.A. – Via XXV Aprile, 4 23804 Monte Marenzo (LC) – Italy
- 39 0341 630506
- info@kong.it
- WWW.KONG.IT
Documents / Resources
| KONG
IT 864.010 10 Holes
Plate
[pdf] Instruction Manual
864.010, 864.011, 864.010 10 Holes Plate, 10 Holes Plate, Plate
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>