PATLITE NE-USB USB Controlled Multicolor Signal Beacon Instruction Manual
- June 12, 2024
- PATLITE
Table of Contents
GA0006316_02
Instruction Manual for the USB Controlled Multicolor Signal Beacon
TYPE NE-USB
Notice to customer
- Thank you very much for your purchase of the PATLITE product.
- To ensure correct use of the product, read this manual carefully before use. And, keep this manual safely for future reference.
- Be sure to read this manual again before you perform maintenance, inspection or repair. If you have any questions, contact our technical/repair service helpdesk shown in the back of this manual.
- For detailed instructions, download the general instruction manual from the PATLITE’s website.
PATLITE’s website: www.patlite.com
To installers or Contractors
- Read this manual thoroughly before using this product to ensure correct use.
- If you have any questions, contact our technical helpdesk shown in the back of this manual.
- Be sure to return this manual to the customer.
Getting started
Safety signs
- Be sure to follow the instructions below that are provided to prevent injury to you and others or property damage. Moreover, the following signs are used to classify and explain the degrees of possible harm and damage that may occur if the product is used incorrectly by the neglect of given signs and instructions.
Warning| Indicates a “hazardous situation which, if not avoided, could
result in death or serious injury.”
---|---
Caution| Indicates a “hazardous situation which, if not avoided, could
result in minor or moderate injury or property damage.”
The safety instructions are classified with the following pictograms.
| **** | This pictogram is used for “don’ts” that you must not do. |
|---|---|
| This pictogram is used for “do’s” that you must do. |
Safety precautions
Warning
To prevent electric shock, short circuit or damage, follow the
instructions below. Be sure to turn off the USB power feed before you perform
cabling, assembly or removal. Failure to follow this instruction may cause a
short resulting in a burn on the internal circuit or electric shock injury.
Use the product in the appropriate condition. Be sure to ask a specialist to
install the product if construction is required. Failure to follow this
instruction may result in electric shock, fire, falling, etc.
To prevent lethal or serious property effects caused by the breakdown or
malfunction of the product, secure sufficient safety by the combined use of
other devices.
****Do not use or get near the product if you have an implanted medical
electronic device such as a cardiac pacemaker. Failure to follow this
instruction may affect the device by the magnetic force of the product.
Caution
Do not allow the buzzer to sound unreasonably close to you. Failure to
follow this instruction may damage your hearing.
Do not use the product with the O-ring or waterproof packing removed.
Failure to follow this instruction may cause breakdown with the deterioration
of waterproof performance.
Do not use the product near a flame or in a hot and humid or a corrosive
or flammable atmosphere. Failure to follow this instruction may cause a
breakdown or malfunction.
When you attach/detach the globe, do not touch the internal connector
terminal. Failure to follow this instruction may cause a breakdown.
After the product has been mounted on a device, do not grab it to climb
up on top of the device. Failure to follow this instruction may cause damage
to the product and result in toppling or fall accidents.
To keep up the dustproof and waterproof function of the product, be sure
to use it with the globe securely attached.
When you remove packing or wrapping materials from the device on which
the product is mounted, take care not to get the materials snagged on the
product. Failure to follow this instruction may cause damage to the product.
Do not use this product near equipment that generates strong electrical
or magnetic fields (such as magnetic cards, medical equipment, electric
devices, speakers). Failure to follow this instruction could result in product
damage and product malfunctions such as data loss. Ensure that the product is
securely installed, making sure that the product does not lost balance or fall
over from the weight of the USB cable. Also, install so that there are no
risks of people tripping over the USB cable. Failure to follow these
instructions may result in injury or product damage. Install the product on a
stable, flat surface free from vibration or impact. Note that the sufficient
force to hold the product may not be obtained depending on the conditions of
the mounting surface (material, environment, steel plate thickness, coating
thickness, etc.). Before installing the product, clean any dust, stains, oil
or iron leavings off the mounting surface and the product’s bottom. Failure
to follow this instruction may scratch the mounting surface or lose the force
to hold the product.
When using a tripod with this product, do not try to move or transport
the product with the tripod attached.
Failure to follow this instruction could result in equipment damage if
the product falls over. When removing the product from a tripod, be sure to
unscrew from the screws of the tripod, instead of trying to unscrew the
product off directly from the tripod. Failure to follow this instruction may
result in injury or product damage.
Note
- Where the product is used for the primary purpose of safety maintenance, be sure to perform daily maintenance.
- Before handling the product, remove static buildup from your body to prevent damage by electrostatic discharge (To remove static charges, touch other grounded metallic area with your bare hands).
- For the handling of the parts of the product, follow the instructions below. Do not disassemble the parts that are not designed as removable. Do not add any modification to the product. For repair parts, be sure to use only those specified in the general instruction manual [web version].
Model Number Configuration
Package contents
NE-SN-USB
NE-WN-USB
*USB cable not included. Please prepare your own.
Names and dimensions of parts
NE-SN-USB
The diagram below shows the product with the slip-proof sheet
attached.
NE-WN-USB
The diagram below shows the product with the waterproof sheet
attached.
Device setup and installation
- Before mounting and cabling work, be sure to have a read through the general instruction manual [web version] (download from the PATLITE’s website).
- Provide a USB cable at the expense of the customer.
Warning
****Be sure to turn off the USB power supply before performing any
installation or maintenance work. Failure to follow this instruction may
result in electric shock or burning of the internal circuit.
Caution
Do not touch the connector of the USB and the internal LED. Failure to
follow this instruction may damage the product.
Do not apply excessive force on the connector while connected to a USB
cable. Doing so may damage the product.
Do not apply excessive force on the product. Doing so may damage the
product.
When connecting the product to a PC, be sure to connect the product
directly to the PC without the use of USB hubs. Using USB hubs may cause
unstable connection and improper operation of the product
Note
- Use a USB cable that is 3m or shorter.
- The Type-C Connector of the USB cable you are connecting should follow the specifications noted on the right diagram.
Mounting Directions
To mount the product, follow the procedures below.
NE-SN-USB
NE-WN-USB
The NE-SN-USB can be mounted in the following ways: direct mount, magnetic
mount, or tripod mounting. When mounting with a tripod, the screw of the
tripod should be no longer than 5.5mm.
Using tripods with screws that are longer than 5.5mm prevents the product from
being properly secured to the tripod, and may cause damage to the product. For
detailed mounting instructions, be sure to reference the instruction manual of
the tripod you are using. When mounting with magnets, a position lower than 2m
is recommended.
Mounting Surface Dimensions
If mounting the NE-WN-USB, prepare the mounting surface according to the
below diagram. If mounting the NE-SN-USB, this step does not need to be
followed.
USB Connection
Learn more about the product
For further product details not covered in this manual, see the web manual.
- The illustrations and photos in this manual may differ partially from how the real product appears.
- The dimensions, specifications and structures of the product are subject to change for improvement without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>