saxby lighting 39168 Knight Spotlight Instruction Manual

Saxby lighting 39168 Knight Spotlight

Product Information

• Product Name: Knight Spotlight

• Model Number: 39168

• Manufacturer: Saxby Lighting

• Manufacturer Address: BH17 7BY (UK), Brilliant AG,
  Brilliantstrasse 1, D-27442 Gnarrenburg (EU)

• Website: www.saxbylighting.com

• Voltage: 220-240V

• Lamp: 3 x Max. 35W GU10 Mains Halogen

• IP Rating: 44

Product Usage Instructions

1. Commissioning:
   • Align the holes on the bracket and secure the light fitting. Take care not to trap any wiring.
   • The light fitting is now ready for use.
2. Fitting/Replacing Bulbs:
   • Ensure the power supply is switched off before changing lightbulbs or cleaning.
   • Use the correct type and wattage bulb. Never exceed the stated wattage.
   • To remove a bulb, turn it a quarter turn anticlockwise and pull it out.
   • To replace a bulb, push it gently into the lampholder and twist it a quarter turn clockwise to engage the pins. Replace the shade by gently screwing it on.
3. Cleaning:
   • Use a soft dry cloth to clean the light fitting.
   • Avoid using solvents or abrasive cleaners as they could damage the finish.
4. Recycling Advice:
   • Waste electrical products should not be disposed of with household waste.
   • Recycle the product where facilities exist.
   • Check with your Local Authority or retailer for recycling advice.
5. Safety Information:
   • Always switch off the power supply before changing lightbulbs or cleaning for your safety.
   • If the glass shade becomes cracked or damaged, replace it immediately before using the fitting.
   • This fitting must not be used without the glass shade in place.
6. Installation:
   • This unit must be fitted by a competent and qualified electrician.
   • Install the light fitting in accordance with IEE Wiring regulations and current Building Regulations.
   • To prevent electrocution, switch off the mains supply before installing or maintaining the fitting. Ensure others cannot restore the electrical supply without your knowledge.
   • The light fitting should be connected to a fused circuit.
   • When changing a bulb, switch off the mains and allow the old bulb to cool down before handling. Dispose of used bulbs carefully and responsibly.
   • This product is suitable for dimming when used with a dimmable lamp. Verify dimming abilities with the lamp manufacturer before use.
7. Layout:
   • Ensure the cables will reach the distance between the junction box and the light fitting.
   • Position cables and junction boxes (not supplied) away from areas where they may be at risk of being cut, trapped, or damaged.
   • Zone 1: 2.25m
   • Zone 2: 0.6m
   • Outside zones

Commissioning

• Replace the cover on tne terminal block.
• Lift the product into place and align the screw holes with the holes on the bracket.
• Using the supplied Allen key, tighten the screws to secure. Take care not to trap any wiring.
• Replace the fuse or circuit breaker and switch on. Your light is now ready for use.

Fitting/replacing bulbs

• When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Used bulbs should not be disposed of with household waste. Please recycle where facilities exist.
• Always use the correct type and wattage bulb. Using the incorrect wattage bulb will damage the product.
• Use a soft cloth to handle bulbs, avoid directly touching the bulbs as this will shorten their life.
• Unscrew the shades anticlockwise. Remove bulb by turning a quarter turn anticlockwise and pulling out.
• Push the bulb gently into the lampholder and twist a quarter turn clockwise to engage pins. Replace the shade by gently screwing on.

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
Glass parts – Wipe clean with a damp cloth. Do not use abrasive materials as these will damage the finish.

Recycling advice

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

Safety information

For your safety, always switch off the power supply before changing lightbulbs, or cleaning.

This bulb is protected by a glass shade. This part must be replaced immediately should the glass shade become cracked or damaged. This fitting must not be used without the glass shade in place.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning

• This light fitting is double insulated (class 2) and does not require connection to an Earth circuit Please read these instructions carefully before commencing any work.
• This unit must be fitted by a competent and qualified electrician.
• Install in accordance with IEE Wiring regulations and current Building Regulations.
• To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
• This light fitting should be connected to a fused circuit.
• If replacing an existing fitting, make a careful note of the connections.
• Always use the correct type and wattage bulb. Never exceed the wattage stated.
• When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling.
• Dispose of used bulbs carefully and responsibly.
• This product is suitable for dimming when used in conjunction with a dimmable lamp. Please ensure verification of dimming abilities with the lamp manufacture prior to use.
• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
• Check with your local authority or retailer for recycling advice.

Specification.

Voltage: 220-240V 50Hz a.c.

Lamp: 3 x Max. 35W GU10

IP rating: 44

Layout

• Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box and the light fitting
• Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged
• The mains supply cable must have a minimum cross-sectional area of 1.0mm2
• This product must be mounted out of arms reach.
• This product has special protection against the ingress of moisture and is IP44 rated.

This product is suitable for use in Zone 2 and outside Zones of a bathroom. See diagram. If this unit is being fitted in a room containing a bath or shower, a 30mA RCD must be used, in accordance with IEE regulations.

Spotlights give a concentrated beam of light and must not be positioned any closer than 0.2M (20cm) to the illuminated surface.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.

• Undo the screws holding the fixing bracket in place and set aside

• Hold the product in place and mark the position of the holes.

• Ensure the ceiling is capable of holding the weight of
  the product. Take care to avoid damaging any concealed
  wiring and pipes.The correct fixings should be used.

• Ensure there is a joist at the point of fixing to support the
  weight of the product.

• Fix the ceiling bracket into position.

Wiring

Having correctly identified the wiring from your existing light fitting, pull the wire through the hole and connect to the connection block inside the product in the following way: This unit is double insulated and must not be earthed. If there are any incoming earth cables, they must be joined together and well-insulated with good quality insulation tape. This is to ensure earth continuity throughout your property.

Check that.

• You have correctly identified the wires

• The connections are tight
  No loose strands have been left out of the connection block

• UK Manufacturer: BH17 7BY

• EU Manufacturer: Brilliant AG,
  Brilliantstrasse 1, D-27442 Gnarrenburg

• www.saxbylighting.com.

References

• Saxby Lighting - Commercial and Domestic Lighting Supplier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>