Tripp Lite U457-025-G1-WPG USB-C to SATA SSD/HDD Enclosure Adapter Quick Start Guide

Tripp Lite U457-025-G1-WPG USB-C to SATA SSD/HDD Enclosure Adapter

Product Features

• Converts any 2.5 in. internal SATA SSD (solid state drive) or HDD (hard disk drive) into an external hard drive for storing data
• Designed for 2.5 in. SATA drive heights between 7 mm and 9.5 mm
• Supports SATA III (6 Gbps), II (3 Gbps) and I (1.5 Gbps) drives
• Backward compatible with USB 3.0, 2.0, and 1.1 devices
• Water-resistant and dust-tight to comply with IP66 standards
• UASP-compatible for enhanced performance
• Bus-powered plug-and-play operation with no software or external power required

Package Contents

• U457-025-G1-WPG (SuperSpeed USB 3.1 Gen 1, 5 Gbps) or U457-025-G2-WPB (SuperSpeed USB 3.1 Gen 2, 10 Gbps)
• Mini Screwdriver
• Screws (x10)
• Washers (x10)
• Quick Start Guide

System Requirements

• USB 3.1 Gen 1 (5 Gbps) port required to achieve maximum speeds for U457-025-G1-WPG
• USB 3.1 Gen 2 (10 Gbps) port required to achieve maximum speeds for U457-025-G2-WPB
• UASP-enabled host controller required to achieve UASP performance
• 2.5 in. SATA HDD or SSD with a maximum height of 9.5 mm

Installation

1. Remove the back cover (side with the screw holes) of the SSD/HDD enclosure.

2. Connect your 2.5 in. SATA SSD/HDD to the SATA connector.

3. Once the SATA SSD/HDD is securely in place, replace the back cover, ensuring the screw holes line up with one another.

4. Using the included screwdriver, screws, and washers, fasten the 10 screws and washers securely to the enclosure.
   Note: In order to comply with IP66 standards, screws need to be properly tightened to the enclosure.

5. Connect the built-in USB 3.1 Type-C cable to an available USB port on your computer.

Specifications

5 Gbps (U457-025-G1-WPG)

SSD/HDD Supported| 2.5 in. SATA I/II/III HDD/SSD
Operating Temperature| 50° to 122°F (10° to 50°C)
Relative Humidity| 10% to 80% RH, Non-Condensing
Dimensions| 0.94 x 3.7 x 5.8 in. (24 x 94 x 148 mm)

Warranty and Product Registration

1-Year Limited Warranty

TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty,

you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service

center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment, which has been damaged by accident, negligence, or misapplication or has been altered or modified in any way. EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Some states do not permit the limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF

ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

Product Registration

Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

• No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

WARNING

Use of this equipment in life support applications where the failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

FAQ’s

What is the Tripp Lite U457-025-G1-WPG USB-C to SATA SSD/HDD Enclosure Adapter?

The Tripp Lite U457-025-G1-WPG is a USB-C to SATA adapter designed to allow you to connect a SATA solid-state drive (SSD) or hard disk drive (HDD) to a computer or device using a USB-C port.

What types of drives are compatible with this adapter?

The adapter is compatible with both SATA SSDs (Solid-State Drives) and SATA HDDs (Hard Disk Drives) of various capacities.

What's the purpose of this adapter?

This adapter allows you to convert your SATA SSD or HDD into an external USB-C storage device. It's useful for data transfer, backup, and accessing data on a drive without installing it internally.

How do I connect my drive to the adapter?

Simply plug the SATA drive into the SATA connector on the adapter. Then, connect the USB-C end of the adapter to a USB-C port on your computer or device.

Is any software installation required for this adapter to work?

In most cases, no additional software installation is required. The adapter should be recognized by your operating system as an external storage device once connected.

Is the adapter bus-powered or does it require external power?

The adapter is typically bus-powered, meaning it draws power from the USB-C port it's connected to. No external power source is usually required.

What operating systems are compatible with this adapter?

The adapter is compatible with various operating systems, including Windows, macOS, and Linux, as it's recognized as a standard storage device.

Can I use this adapter for cloning or transferring data between drives?

Yes, this adapter is commonly used for cloning or transferring data between drives. You can connect the source drive and the target drive to your computer simultaneously and perform data transfer tasks.

Is this adapter suitable for both home users and professionals?

Yes, this adapter is suitable for a wide range of users, from casual home users who want to access or back up their data to professionals who need to troubleshoot, recover, or migrate data.

What are the data transfer speeds of this adapter?

The data transfer speeds are determined by the SATA interface and the quality of the connected drive. In general, you can expect USB 3.1 Gen 1 speeds (up to 5 Gbps), which is sufficient for most SATA drives.

Can I use this adapter to boot from an external drive?

Yes, you can typically use this adapter to boot from an external SSD or HDD, as long as your computer's BIOS or UEFI supports booting from USB devices.

Does the adapter support hot-swapping?

Yes, USB-C supports hot-swapping, allowing you to connect or disconnect the adapter while the computer is running. However, it's always a good practice to safely eject the drive before disconnecting to prevent data loss.

Download this PDF Link: Tripp Lite U457-025-G1-WPG USB-C to SATA SSD/HDD Enclosure Adapter Quick Start Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>