JOYROOM JR-CB6 Car-B Series Wireless Receiver User Manual
- June 12, 2024
- Joyroom
Table of Contents
JOYROOM JR-CB6 Car-B Series Wireless Receiver User Manual
I. Product picture
II. Basic parameters
Name: Car-B Series Wireless Receiver
Model: JR-CB6
BT version: V5.3
Audio decoding: AAC, SBC
Supported protocols: HFP, A2DP, AVRCP
Working frequency: 2400MHz-2483.5MHz
BT range: 10m (barrier-free open environment)
Frequency response range: 20Hz-20KHz
Microphone sensitivity: -38dB±2
Input port: USB+AUX
Cord length: 100cm
Power input: 5V 1A
Material: ABS+PC
Size: 57mm23mm8.8mm
Net weight: 15g
III. Pairing operation
IV. Operation instructions
V. Indicator light
Turn on The LED ring has constant ice-blue, purple and orange light for 1s Turn off: The LED ring turns off Ready for pairing: The LED ring slowly breathes ice-blue, purple and orange at the same time Connected to phone: The LED ring has constant ice-blue, purple and orange light Factory reset: The LED ring quickly flashes ice-blue, purple and orange at the same time for 5 times
VI. FAQ
Q: Why can’t the receiver be connected?
A: ① It may be that the receiver has been connected to another device (such as a computer or mobile phone). Please disconnect it from the device and make a reconnection. ② Since the iP phone’s BT has no automatic refresh function, you can click “JR-CB6” manually on the BT interface. ③ If above operations failed, you can restore the receiver to factory settings
Q: Why is the sound of the receiver too low?
A: ① If you are an Android user, it may be that the playback channel of the mobile phone is not turned on. Please turn your phone’s BT function on, click the icon on the right side of the connected earphones to turn on the “media channel and call channel”. ② If you are an iP user, please open your phone’s “Settings” interface, and check if there is a maximum volume limit on the phone. ③ Due to different operating systems of different phones, the volume of the receiver may not be synchronized with the volume of the phone/car audio. Please manually volume up the mobile phone, the receiver and the car audio respectively
Q: Why can’t the receiver be turned on when connected with power?
A: ① The USB charging port and cable may not be connected properly, please pull the cable out and plug it in again repeatedly to make sure it is well inserted. ② Please use adapters or car chargers that conform to national/regional safety standards to supply power for the product. Adapters with excessive power may be incompatible. ② The product does not support PD protocol, when using PD power adapters to supply power for the product, it may be incompatible.
VII. Safety Criterion
- Please follow the instructions, do not disassemble the product or refit it for any reason, otherwise it may break down or burn down.
- Do not immerse it in any liquid or wash it with water.
- Please use adapters that conform to national/regional safety standards together with the included charging cable to charge the product, otherwise its battery may be damaged or cause safety problems.
- Please use and store it in normal temperatures; too low or too high temperature (below 0¥ or above 35¥) is not permitted.
- Do not block the openings of the product, such as charging port, audio port and microphone, etc.
- Do not use it under thunderstorm which may lead to abnormal performance and signal interruption.
FCC NOTE:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
3.1101.618928.0000000
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>