genio I003972 4M Wi-Fi LED Pixel Strip Light Instruction Manual

genio I003972 4M Wi-Fi LED Pixel Strip Light Instruction Manual

WARNING:

•  LED STRIP LIGHT CAN BE USED INDOOR OR OUTDOOR UNDER THE SHADE ONLY
•  ADAPTOR/ TRANSFORMER AND Wi‐Fi CONTROLLER MUST REMAIN INDOOR AT ALL TIMES

TO ENSURE THE SAFE AND SATISFACTORY OPERATION OF THIS SET PLEASE READ

THESE INSTRUCTIONS CAREFULLY AND
RETAIN FOR FUTURE REFERENCE FOR ANY QUESTIONS OR TROUBLESHOOTING PLEASE VISIT www.mirabellagenio.com.au

We recommend that the set be tested prior to being set up in the desired location

SAFETY INFORMATION:

• Remove set from the packaging before connecting to the power supply.
• Before using or re‐using the set, inspect the set carefully
• Use only with the adaptor/transformer supplied
• Do not connect the set electrically to another set from a different manufacturer
• Ensure that the cable is completely uncoiled whilst set is in use. Failure to do so may cause overheating
• Avoid damage to wire insulation (cable), as this could cause a short‐circuit and damage the transformer
• Do not use any set which has been: cut, damaged, or has frayed wire insulation, loose connections or exposed wires

Note: When connecting, please ensure the arrows are aligned with one another, otherwise it will NOT light up

When cutting the strip light, please only cut along the cutline as outlined in the diagram

1. Connection Preparation

Your phone must be connected to 2.4Ghz Wi‐Fi and not the 5GHz, To verify your mobile phone is connected a 2.4Ghz Wi‐Fi network, Navigate to the Setting menu and click on Wi‐
Fi. In this menu you will see all detectable networks in your area. Locate the SSID for your network, select a Wi‐Fi SSID that doesn’t end with 5GHz.
Check you have a strong Wi‐Fi signal (at least two bars) in the location where the smart device is installed.
If you don’t have at least two bars signal on your phone, then you may need to reconsider the location or getting a Wi‐Fi extender to boost the Wi‐Fi signal strength.
If you have dual band router but you don’t see two Wi‐Fi name SSID’s, one with 5G and one without 5G, you MUST log into the router and manually disable the 5Ghz Wi‐Fi signal if you’re having connection issues. Please contact your internet provider on how to disable 5Ghz Wi‐
Fi for your router or check our website;s FAQ for some common router settings. Install the APP and register Account
For the best experience, download the “Mirabella Genio” APP to your smartphone from the App Store or Google Play, the APP icon will be displayed after it’s installed successfully

EZ method – when the light is fast blinking (2 blinks per second)

1.  Connect the light strip then switch on the power, wait a few seconds, strip light will be blinking fast

2. If it did not automatically start to blink fast when first powered on, press and hold the pairing button on the Wi‐Fi controller, until the light starts to blink rapidly (2 blinks per second)

3. Open Mirabella Genio APP, tap on +, add Manually then choose genio strip light from the list
   

4. Entre your 2.4Ghz Wi‐Fi name and password, (make sure Wi‐Fi name doesn’t end with ‐5G)
   Follow the APP instruction carefully to complete the network pairing process.

if the fast‐blinking method (EZ method, mentioned above) doesn’t work, please try the slow blinking (AP method) below.
While the strip light is rapidly blinking, press and hold the pairing button on the Wi‐Fi controller again and then wait for the light to start blinking slowly (1 blink per every 2 seconds)

1. open up the Mirabella genio APP, tap on + , add Manually then choose genio strip light from the list
   Entre your 2.4Ghz Wi‐Fi name and password, (make sure the Wi‐Fi name doesn’t end with ‐5G) then in reset the device first screen tap on EZ mode in the Top right hand corner just below the battery image , select AP Mode (refer to the 1st and 2nd image below) Now Confirm indicator slowly blinking (refer to image 3), hit Next, then Go to connect and connect to Wi‐Fi named SmartLife_XXXX
   

2. After connected to SmartLife_XXXX, return back to Mirabella Genio, APP will commence adding device
   

If you don’t have Wi‐Fi at home or cannot pair it but still want to use this light, simply wait for the light stopped blinking, then you can short press the pairing button to change different modes without the need of genio APP. Should the transformer, supply plug or supply flexible cord get damaged, do not attempt to repair.

TO BE REPAIRED BY AN AUTHORIZED PERSON ONLY

THIS IS AN AUSTRALIAN STANDARDS REQUIREMENT IN THE INTEREST OF YOUR SAFETY·

FAQ:

Q. I have internet/power outage and device went offline and doesn’t reconnect back online by itself?
A. Go the strip light co’ settings page (pencil icon), look for “remove device” Remove it and reset the device and pair it again

through the app.

Q. how do I control two or more strip lights at the same time?
A. Go the device’ settings page (pencil icon), look for the “create group” option,
If you are using Telstra/Optus NBN and you still having issue with pairing when use AP method, please call our tech support line or check our online FAQ pages on how to disable the 5Ghz WiFi on the router setting www.mirabellagenio.com.au/faqs

Mirabella International Pty Ltd
1 Mirabella Drive Tullamarine VIC. 3043 Australia
t: 1800 636 528
e: customerservice@mirabella.com.au

Read More About This Manual & Download PDF:

References

• Mirabella Genio - Smart Home
• FAQs - Mirabella Genio - Smart Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>