WINEGARD LNA-200 Boost XT Digital HDTV Preamplifier User Guide
- June 12, 2024
- WINEGARD
Table of Contents
WINEGARD LNA-200 Boost XT Digital HDTV Preamplifier
Product Information
The Smart Preamplifier is a device designed to enhance the performance of your TV antenna. It allows you to maximize the number of free channels you can receive and provides a signal meter for fine-tuning the antenna position. The preamplifier is compatible with the Winegard App, which can be downloaded by scanning the QR codes provided.
Please note that the preamplifier does not come with coax cables or a mast. You will need to provide these items separately. The preamplifier can be secured to the mast using the provided cable ties.
For more information about the product, you can scan the QR codes or contact Winegard directly through the provided phone number or email address. The product is backed by a warranty, and you can register your product on the Winegard website for additional support.
Product Usage Instructions
-
Work with a buddy: It is recommended to have one person adjusting the antenna while another person relays the results.
-
Download Winegard App: Scan the QR codes below to download the Winegard App from either the App Store (for Apple devices) or Google Play (for Android devices).
-
Connect the preamplifier:
- Use coax cables (not included) to connect the preamplifier to both the antenna and signal meter.
- Turn on the signal meter by connecting it to an outdoor power outlet or a power bank (not included).
- Note: The TV does not need to be connected to the signal meter during initial antenna setup.
-
Position the antenna:
- Scan the QR code on the signal meter using the Winegard App.
- Position the antenna to receive the maximum number of free channels.
- Allow six to twelve seconds between each re-positioning.
- HINT: The Winegard App provides different views to help with
positioning, including a top-down view of broadcast towers, a list of detected channels, and a signal strength view for fine-tuning specific channels if necessary.
-
Tighten the antenna and connect the signal meter to the TV:
- Once the antenna is positioned for best reception, tighten its position.
- Move the signal meter inside and connect it to the TV using a coax cable (not included).
- Provide power to the signal meter by connecting it to an indoor outlet, a power bank (not included), or an extension cord if the signal meter and smartphone/app are more than 30 ft apart.
- Run a channel scan on the TV to detect available channels.
Product Troubleshooting
If you encounter any issues with the Smart Preamplifier, refer to the following troubleshooting steps:
-
Problem: SUMMARY SCREEN Total Channels shows all zeros.
Possible Cause: App connection to database lost. Possible Solution: Close the app and reopen it. Also, ensure that the antenna is placed in the correct location and allow the timer to cycle twice while repositioning the antenna. -
Problem: Total Channels shows all dashes. Antenna has encountered a problem.
Possible Cause: Not all channels are GREEN. Antenna position, distance, terrain, weather, network power, or band may affect signal strength. Possible Solution: Reboot the signal meter by unplugging it for 3 seconds and restoring power. Reposition the antenna to get as many channels as possible in GREEN and YELLOW (channels with these colors should be viewable). Zoom in on the map in the Winegard App to see if the network tower appears. -
Problem: The network that I want remains RED.
Possible Cause: Antenna position, distance, terrain, weather, network power, or band may affect signal strength. Possible Solution: Reposition the antenna and ensure that as many channels as possible are in GREEN and YELLOW (viewable channels with these colors). Zoom in on the map in the Winegard App to see if the network tower appears.
INSTALLATION
IMPORTANT: Work with a buddy! One person adjusts antenna, second person relays results.
CONTENTS
- USB cable
- preamplifier
- 110V power adapter
- signal meter (power inserter)
Not provided: coax cables, mast
- SCAN QR Codes below to download the Winegard App.
- SELECT “Don’t have an account?” Fill out info and CLOSE the app. An email confirmation will be sent. Confirm the email (required). Open app and log in.
- CONNECT the preamplifier to the antenna and signal meter using coax cables (not included). Turn on the signal meter by connecting it to an outdoor power outlet or power bank. The TV doesn’t need to be connected to the signal meter during initial antenna setup.
- SCAN the QR code on the signal meter. Position antenna to receive the maximum number of free channels. Allow six to twelve seconds between each re-positioning. HINT: Different views are available: a top-down view of broadcast towers in your area, a full list of actual channels your antenna detects, and a signal strength view to help fine-tune a specific channel if necessary.
- POSITION and tighten the antenna for best reception. Move signal meter inside and connect to the TV. Provide power to the signal meter (a). Run a channel scan on the TV.
TROUBLESHOOTING
| Problem | Possible Cause | Possible Solution |
|---|
SUMMARY SCREEN
Total Channels show all zeros.| App connection to database lost.| Close the
app and reopen.
The antenna was placed in the wrong location.| Allow the timer to cycle twice
while repositioning the antenna.
Total Channels show all dashes.| The antenna has encountered a problem.|
Reboot by unplugging the signal meter, waiting 3 seconds, and restoring power.
Not all channels are GREEN.| Antenna position, distance, terrain, weather,
network power, or band may affect signal strength.| Reposition the antenna to
get as many channels as possible in GREEN and YELLOW (channels with these
colors should be viewable).
MAP SCREEN
The network does not appear.| Networks may be on the same tower, or very close
and hidden.| Zoom in on the map to see if the network tower appears.
The network that I want remains RED.| Antenna position, distance, terrain,
weather, network power, or band may affect signal strength.
| Click/hover over the network and verify the network distance is within the
antenna range.
Click/hover over the network you are looking for. Verify the antenna covers
the required band (UHF, VHF High; VHF Low).
Try turning off the amplifier. Go to Settings, disable Distribution Amplifier, and click OK. Or click Dist. Amp on the Success screen.
Important: This option may only work on individual channels when the signal tower is close by—the amplifier may be overpowering the signal.
LIST VIEW
Channel data refreshes before I find the channel.| Channel data refreshes
every 6 to 12 seconds and moves to the top of the screen.| Press the Pause
button at the bottom of the screen so that you can see the channels you have.
Restart whenever you are ready.
DEVICE CONNECTION
I can’t scan the barcode.| The camera won’t focus, or you’re not signed in to
your account.| Ensure you are signed in to your Winegard account. Adjust the
distance from your camera to the QR code. If this doesn’t help, tap the
Continue without scanning button, then tap Scan for Bluetooth® Devices to
manually find and connect to your antenna.
Cannot connect to the device.| The signal meter is not powered on.| Ensure the
signal meter is powered on and try again.
The scan code is not recognized.| Scanned the wrong QR code, or there is a
decoding error.| Check that the QR code is not damaged, then center the camera
on only the Winegard scan code.
A message appears that the device is disconnected.| Out of range of the signal
meter, or power to the signal meter was lost.| Make sure your signal meter is
powered on; stay within 30 feet of the signal meter to ensure the Bluetooth
connection is not lost.
ACCOUNT SIGN IN
My account needs to be verified.| Email verification is needed.| Check for
account verification email messages from Winegard. Follow the instructions.
Check your spam filter.
Invalid password.| Incorrect password.| Re-enter your password or reset your
password and follow the instructions.
BLUE LED
LED is no longer solid or flashing.| Sleeps after 15 minutes of inactivity.|
This is normal operation when the unit goes to sleep. A connection to the
antenna may still be made when the blue LED is off.
The LED light is no longer on.| Bluetooth connection is in sleep mode.| The
antenna/Amplifier is still working with the LED off, the Bluetooth connection
is in sleep mode.
The signal meter is not powered on.| Ensure the signal meter is powered on and
try again.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and devices.
- Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
- Only channels 1–11 can be operated. Selection of other channels is not possible.
- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 25 cm between the radiator and your body. This device
and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter except in accordance with FCC multi-transmitter
product procedures. This device complies with FCC and Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of
the device.
SCAN FOR
- MORE PRODUCT INFORMATION
WARRANTY
- WARRANTY OR CALL 800-288-8094
For help, email help@winegard.com or call 1-800-288-8094 Register your product at: www.winegard.com/support.
Winegard Company 2736 Mt. Pleasant St. | Burlington, IA 52601. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Google Play and the Google Play logo are trademarks of Google LLC. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Winegard is under license. Winegard is a registered trademark of Winegard Company.
Printed in U.S.A. © 2022 Winegard Company Rev 2-23 2452453.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>