Chy Firemate VEABT008 Module User Manual
- June 5, 2024
- Chy Firemate
Table of Contents
Chy Firemate VEABT008 Module
Features
- On-chip low power microcontroller
- Up to 1024 kB flash program memory
- Up to 96 kB RAM data memory
- On board crystal and PCB Antenna
Application
- Mobile device accessories (Android/ iOS)
- Wireless data communication
- Remote sensors
Pin definition (from right to left)
| Pin No. | Description | Pin Type | Functions |
|---|---|---|---|
| 1 | BLE_RX | Digital I/O | UART RX |
| 2 | BLE_TX | Digital I/O | UART TX |
| 3 | WAKE_UP | Output | Digital I/O |
| 4 | STATUS | Input | Digital I/O |
| 5 | GND | Digital I/O | GND |
| 6 | V+ | Digital I/O | VDD |
| 7 | BLE_EN | Digital I/O | VDD Enable |
How to use
- Before sending any UART Command, “WAKE_UP 1 → 0” must be done by external MCU.
- If the RF module is connected to Smart Devices (Android/ iOS), the pin STATUS will be logic “1” to inform external MCU.
- Beacon
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).
End Product Labeling
This transmitter module is authorized only for use in devices where the
antenna may be installed such that 20 cm may be maintained between the antenna
and users. The final end product must be labeled in visible area with the
following: “Contains FCC ID: VEABT008”
End Product Manual Information
The user manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain
laptop configurations or colocation with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization. This device is intended only for OEM
integrators under the following conditions: The antenna must be
installed such that 20 cm is maintained between the antenna and users. As long
as the condition above is met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirements required with this module installed
(for example, digital device emissions, PC peripheral requirements, etc.).