HEAT GLO PRIMO-II-60ST Direct Vent Gas Fireplace Installation Guide
- June 12, 2024
- HEAT GLO
Table of Contents
HEAT GLO PRIMO-II-60ST Direct Vent Gas Fireplace
Product Information
- Product Name: PRIMO-II-60ST
- Product Type: Double-Sided Direct Vent Gas Fireplace
- Actual Dimensions:
-
- Front Width: 76-3/8 [1940]
- Height : 40-13/16 [1037]
- Depth : 18-1/4 [464]
- Glass Size: 60 x 18 [1524 X 457]
- BTU/Hour Input:
-
- NG (Natural Gas): 39,500 – 57,000 BTUs
- LP (Liquid Propane): 36,500 – 50,000 BTUs
- Framing Dimensions:
-
- Front Width: 78-3/4 [2000]
- Height: 45 [1143]
- Depth: 17 [432]
- Weight: 423 lbs [192 kgs]
- Product Listing Codes:
-
- US: ANSI Z21.50-2019
- CAN: CSA 2.22-2019
Product Usage Instructions
- Before installation, refer to the installation manual by scanning the QR code provided for final dimensions and requirements.
- Ensure clearances to combustibles are maintained during installation.
- Construct a platform if installing the appliance off the floor, following local building codes.
- Adjust framing dimensions for interior sheathing (such as 1/2 drywall).
- Provide clearance from the top edge of the opening to the bottom of the appliance, which should be 33-15/16.
- Ensure the vent framing hole is not packed with insulation or other materials.
- Follow the instructions accompanying the product strictly to avoid the risk of fire and potential injury.
Note: Please refer to the complete user manual for detailed installation and usage instructions.
ACTUAL DIMENSIONS
- FRONT WIDTH: 76-3/8″ [1940]
- HEIGHT: 40-13/16″ [1037]
- DEPTH: 18-1/4″ [464]
- GLASS SIZE: 60″ x 18″ [1524 X 457]
- BTU/HOUR INPUT:
- 39,500 – 57,000 BTUs (NG)
- 36,500 – 50,000 BTUs (LP)
FRAMING DIMENSIONS
- FRONT WIDTH: 78-3/4″ [2000]
- HEIGHT: 45″ [1143]
- DEPTH: 17″ [432]
- WEIGHT: 423 LBS [192 KGS]
- Adjust framing dimensions for interior sheathing (such as 1/2″ drywall)
- Header depth not to exceed 5-1/2″. If header depth is greater than 3-1/2″, header must be notched in order to maintain clearance to pipe.
- If appliance is installed off of floor, maintain required clearances to combustibles. Construct platform in accordance to local building codes.
Specifications
COMBUSTIBLE OR NON-COMBUSTIBLE MANTELS
COMBUSTIBLE OR NON-COMBUSTIBLE MANTEL LEGS OR WALL PROJECTIONS
WALL PENETRATION
DO NOT PACK VENT FRAMING HOLE WITH INSULATION OR OTHER MATERIAL
Shows center of vent framing hole for top venting. The center of the hole is
one 1″ (25mm) above the center of the horizontal vent pipe.
Note: Center of the horizontal vent pipe to the vertical measuring
surface of a trap cap is 5″ (127mm).
Product information provided is not complete and is subject to change without
notice. Product installation must adhere strictly to instructions accompanying
product to avoid risk of fire and potential injury.
ABOUT COMPANY
- Heat & Glo — A Brand of Hearth & Home Technologies
- 7571 215th Street West
- Lakeville, MN 55044
- 877-486-9123
- heatnglo.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>