Claber 8425 Aquauno Pratico Plus Drip Line Instruction Manual
- June 12, 2024
- claber
Table of Contents
Pratico
8425
**TECHNICAL DATA
**
Power supply| 1x 6LR61
9 VOLT
alkaline
---|---
Average life of the
battery| 1 year
Degree of protection| IP 20
Operating temp.| 3 – 50 °C
Operating pressure| MIN: 0,5 bar
MAX: 10 bar
Plastic materials| >ABS<
PC<
POM<
TPE<
Water pressure table
| Bar | 0,5 | 1 | 2 | 2,5 | 3 | 4 | 5 |
|---|---|---|---|---|---|---|---|
| l/min | 14 | 19 | 27 | 30 | 33 | 38 | 42 |
GENERAL INFORMATION
Always keep the cover closed
FILTER WATER
Use water from the mains tap or filter the water before using it.
DESCRIPTION
- Inspectable and washable filter
- 3/4” F tap connector
- Ring nut
- Start of watering setting
- Led
- End of watering setting
- Protective cover
- 3/4″ threaded male connector
- Quick-Click male connector
BATTERY REPLACEMENT
| 
---|---
| 
When the LED flashes in red, this means the battery is low.
Replace the battery as soon as possible. When the battery is completely flat,
the water timer automatically stops its functions and closes the valve. Only
use new 9 V Alkaline 6LR61 batteries, with an expiry date exceeding one year
and that have never been used. Replace the battery at the beginning of each
season. Never replace the battery during irrigation, otherwise the water will
continue to flow at the end of the cycle.
After changing the battery, do I have to reprogramme the water timer? After
the battery has been replaced, repeat programming.
INSTALLATION
Do not install the water timer inside valve boxes, below ground level or indoors. Do not use the water timer with operating pressures lower than 0.5 bar (7.3 psi) or higher than 10 bar (145psi).
MAINTENANCE
https://www.claber.com/conformity/
WARNING
Read this instruction manual carefully and keep it handy for future
reference. This device has been designed and manufactured exclusively for the
setting of watering time by adults with experience and knowledge. Any use
other than that described in this manual is considered improper: the
manufacturer acknowledges no liability for damages arising from improper use,
which will also void the warranty.
Do not power the water timer with sources other than those specified. It is
good policy – when the water timer is used for the first time – to make
certain that the programmes run correctly. Do not use the water timer with
chemicals or liquids other than water.
At the end of the season, before the winter frosts, disconnect the timer from
the tap, remove the battery and store the timer in a sheltered place, away
from damp, where the temperature does not fall below 3°C.
The symbol in question applied to the product or the packaging indicates that
the product must not be considered as normal domestic waste, but must be taken
to a special centre for the collection and recycling of waste electrical and
electronic equipment. Take care to dispose of this product in the proper way;
this will help to avoid the negative consequences that could arise from
unsorted collection or dumping. For more detailed information on the recycling
of this product, contact the municipal authority, the local refuse collection
service or the dealer from whom the item was purchased.
CONDITIONS OF GUARANTEE
This device is guaranteed for 3 years from the date of purchase as indicated
by the invoice, bill or till receipt issued at the time of the transaction,
which must be kept. Claber guarantees that the product is free of material or
manufacturing defects. Within two years from the date of delivery to the
consumer, Claber shall repair or replace any parts of this product found to be
defective.
The warranty is void in the event of:
- Lack of proof of purchase (invoice, receipt or cash register receipt);
- Use or maintenance different from what is specified;
- Disassembly or tampering by unauthorised personnel;
- Faulty installation of the product;
- Damages from atmospheric agents or contact with chemical agents;
Claber accepts no liability for products that it has not manufactured, even if
used in combination with its own products.
The costs and the risks associated with shipment are met entirely by the
owner. Assistance is provided by Claber authorized service centres.
Declaration of Conformity
Claber S.P.A. Via Pontebbana, 22 – 33080 – Fiume Veneto – Pordenone – Italy
Assuming full responsibility, we declare that the product 8425 – Pratico
complies with the applicable European and British directives, as per the
Declarations of Conformity accessible via the following link:
www.claber.com/conformity/
Fiume Veneto, 11/2022
Il Presidente Claber S.P.A.
Ing. Gian Luigi Spadotto
USE
HOW MUCH TO WATER (watering run time)
Watering run time is set in one of the following ways: standard solution,
expert solution. The timer irrigates once a day every 24 hours. The run time
of the irrigation cycle can be set to between 1 and 60 minutes.
STANDARD SOLUTION
3. Interrupt watering cycle when sufficient (e.g. after 15 minutes)
The saved run time (15 minutes) is repeated every 24 hours.
Not able to count the flashes in time? The procedure can be repeated any time
starting from point (1).
EXPERT SOLUTION
3. Within 1 minute of watering, press and hold STOP without releasing it
Then, count the flashes (1 flash = 1 minute of irrigation)
When the required run time has been reached (e.g. 15 flashes = 15 minutes), release the key button the stored run time (15 minutes) will be repeated at each watering cycle
2. WHEN TO WATER (watering start time)
Irrigation always takes place at the time the timer was set. For example,
if you start irrigation for 15 minutes at 20:00, irrigation will start at
20:00 on the following days and will last for the same time (15 minutes),
until a new programme is set. If you forget to press STOP the first time the
timer is programmed, it will irrigate for an hour on that day and then for 5
minutes only on the following days.
3. WATERING FREQUENCY (how often to water )
The frequency is daily (every 24 hours) and cannot be modified by the user
(for example, every day at 20:00).
LED INDICATIONS
| (flashing quickly) watering in progress
---|---
| (flashing slowly) no watering in progress
| (red flash) battery flat. Replace as soon as possible
| (led off ) the battery is completely flat or the water timer is set to OFF
and will not water automatically until new setting is carried out
5. STOPPING WATERING IN ADVANCE WHEN ALREADY UNDER WAY
Press the red STOP button to stop the irrigation cycle in progress. It will
not start again until the next day. Pressing the green START button will NOT
restart the irrigation cycle.
6. SET TO OFF
By pressing the RED and GREEN key buttons at the same time, all settings are
reset and the timer goes to OFF.
DISPLAY OF SET RUN TIME
Key
| 4 short, quick consecutive flashes indicate that the tens are set to zero
(e.g. 01 minute) or the units are set to zero (e.g. 10 minutes).
---|---
| 1 flashing slowly
| The set watering run time can be viewed at any moment, for example, during
the wait time between one watering cycle and the next one. Press the GREEN
key: the LED light activates. Release the GREEN key. The LED remains off for 3
seconds, then starts flashing according to the number of minutes set.
Es. 03 min.
| The LED remains off for 3 seconds
---|---
| 4 short, quick flashes indicate tens = 0
| The LED remains off for 3 seconds
| 3 slow flashes indicate 3 minutes
Es. 10 min.
| The LED remains off for 3 seconds
---|---
| 1 slow flash indicates 10 minutes (1 ten)
| The LED remains off for 3 seconds
| 4 short, quick flashes indicates units = 0
Es. 23 min.
| The LED remains off for 3 seconds
---|---
| 2 slow flashes indicate 20 minutes (2 tens)
| The LED remains off for 3 seconds
| 3 slow flashes indicate 3 minutes (3 units)
If the timer does not start the water flow and the LED is flashing red,
replace the battery.
If I accidentally touch the RED key, will setting be cancelled? No,
programming is saved but if there is an irrigation cycle running it will be
stopped and the programme will run the next day.
I want to change the watering run time. Reset the water timer by pressing the
GREEN and RED keys at the same time and repeat setting entering the new run
time value
I want to change watering frequency (i.e. the number of daily watering
cycles). The water times ONLY carries out one watering cycle per day (every 24
hours).
This setting cannot be changed.
I want to change the daily watering start time. Watering cycles start every
day at the time set in the water timer. The only way to change this time is to
reset the water timer by pressing the GREEN and RED keys at the same time and
repeat setting to the time required
Follow us onwww.claber.com
Represented by:
Authorised Rep Compliance Ltd., ARC House, Thurnham,
Lancaster, LA2 0DT, UK.
http://claber.it/q.asp?q=84250000
CLABER SPA – Via Pontebbana, 22 – 33080 Fiume Veneto PN – Italy
Tel. +39 0434 958836 – Fax +39 0434 957193
[email protected] –
www.claber.com
Documents / Resources
|
Claber 8425 Aquauno Pratico Plus Drip
Line
[pdf] Instruction Manual
8425 Aquauno Pratico Plus Drip Line, 8425, Aquauno Pratico Plus Drip Line,
Pratico Plus Drip Line, Plus Drip Line, Drip Line
---|---