claber 87321 Turbina Medium Range Sprinkler User Manual
- June 3, 2024
- claber
Table of Contents
claber 87321 Turbina Medium Range Sprinkler
DESCRIPTION
- A Nozzle operating position
- B Jet adjustment screw
- C Slot to insert key or screwdriver to select the nozzle
- D Indicator of operating arc
- E Irrigation area adjustment
- F Hole for pulling up the turret
- G Key
For multi-jet turbine with long jet range (code)
DETERMINING THE OPERATING ARC
(pre-set at 180°). Setting the irrigation start point
- Pull the turret up and turn it anti-clockwise with your hands (1-2), without forcing it (3) until you reach the stop, then turn it clockwise (4) without forcing it, until it stops again.
- This is the adjustment starting point.
- The sprinkler will start operating from this point, turning anticlockwise.
Adjusting the operating arc before installation(pre-set at 180°)
- To increase the irrigation area: insert the key in slot “E” (1), hold the turret still with your hand and turn the key clockwise (2) until indicator “D” is pointing at the required irrigation angle.
- To decrease the irrigation area: hold the turret still and turn the key anticlockwise (3).
SELECTING THE NOZZLE
Nozzle | **Angle** |
---|---|
1 | 40° – 135° |
2 | 136° – 225° |
3 | 226° – 315° |
4 | 316° – 360° |
(pre-set with nozzle 2). In the pulled up position, insert the key supplied, or a flat screwdriver, in the hole to select the nozzle on the top of the turbine. Turn the key or screwdriver to choose the required nozzle according to the operating angle set.
INSTALLATION
- Install and bury. Screw the sprinkler onto the 3/4” threaded extension on the irrigation line (1), adjusting the height to be at ground level (2).
- Turn the central body of the sprinkler. In the pulled up position, hold the central body below the turret and, with the nozzle in the start position, turn it to the required start position (3).
- Important: never hold the sprinkler by the turret.
- Hold the sprinkler still only by grabbing the central body below the turret.
- Once the start position has been determined, follow the instructions to increase or decrease the irrigation area, as described above.
- The latter operation can be done to adjust the sprinkler also when operating or already underground.
FILTER
Unscrew the ring nut and pull out the complete sprinkler assembly. The filter is located on the botton of the sprinkler assembly and can be easily removed, cleaned and reinserted
TABLES INDICATING WATER USAGE OF SPRINKLERS
Turbina __**40°-360° __**
90480
bar
| |
l/min
| ****
m
| ****
m
1,0
| 1
2
3
4
| 3,5
5,6
9,3
12,6
| 7,5
8,4
7,8
6,5
| 10,7
11,9
11,1
9,2
2,0
| 1
2
3
4
| 4,8
7,9
13,3
18,5
| 10,0
11,0
11,8
11,4
| 14,2
15,5
16,7
16,2
3,0
| 1
2
3
4
| 5,9
9,8
16,5
22,4
| 10,5
12,0
13,0
13,6
| 14,9
17,0
18,5
19,3
Documents / Resources
|
claber 87321 Turbina Medium Range
Sprinkler
[pdf] User Manual
87321 Turbina Medium Range Sprinkler, 87321, Turbina Medium Range Sprinkler,
Medium Range Sprinkler, Sprinkler
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>