Perlick HH24RO42L Residential Undercounter Refrigeration User Guide

Perlick HH24RO42L Residential Undercounter Refrigeration

Product Information

• Product Name: Perlick Residential Undercounter Refrigeration
• Model Number: [Model Number]
• Serial Number: [Serial Number]
• Manufacturer: Perlick
• Website:www.perlick.com

General Information

• Congratulations on your purchase of a Perlick Residential undercounter product. This manual has been prepared to assist you in the installation, operation, and maintenance of your undercounter refrigerator.
• If service is required, please contact your dealer for a list of qualified service agents. Do not return merchandise without prior approval.

Warranty

• To register your product, please visit the Perlick website and complete the Warranty Registration Form. Failure to register may result in the installation date reverting back to the ship date. Please record the purchase date and dealer information for future reference.

Safety

• Before installing or operating the unit, it is important to read and understand all instructions provided in this manual. Pay attention to the DANGER, WARNING, CAUTION, and NOTICE information, as they are crucial for the safe and efficient use of your Perlick unit.
• DANGER: Indicates a hazard that will result in serious injury or death if precautions are not followed.
• WARNING: Indicates a hazard that may cause serious injury or death if precautions are not followed.
• CAUTION: Indicates a hazard where minor or moderate injury may occur if precautions are not followed.
• NOTICE: Indicates that property damage may occur if warnings or instructions are not followed.

Refrigerant

• DANGER: Take caution when handling, moving, and using the product to avoid damaging the refrigerant tubing or increasing the risk of a leak.
• WARNING: All service work should be performed by factory-authorized service personnel. When replacing component parts, ensure that like components are used to minimize the risk of possible ignition due to incorrect parts or improper service.

PERLICK RESIDENTIAL UNDERCOUNTER REFRIGERATION
To prevent appliance damage and injury, read these instructions thoroughly prior to operation.

GENERAL INFORMATION

Introduction

• Congratulations on your purchase of a Perlick Residential undercounter product. This manual has been prepared to assist you in the installation of your cabinet and to acquaint you with its operation and maintenance.
• This manual has been prepared to assist you in the installation of your under-counter refrigerator and to acquaint you with its operation and maintenance.
• We dedicate considerable time to ensure that our products provide the highest level of customer satisfaction. If service is required, your dealer can provide you with a list of qualified service agents. For your own protection, never return merchandise for credit without our approval.
• We thank you for selecting a Perlick product and assure you of our continuing interest in your satisfaction.

Warranty

• To register your product, visit our web site at www.perlick.com. Click on “Residential”, then “Resources”. Click on the link “Warranty Registration Form”. You must complete and submit this form or the installation date will revert back to the ship date.
• Please record the purchase date and the dealer’s name, address, and telephone number below.
• Model Number: ____
• Serial Number: _____
• Purchase   Date: _____
• Dealer Name & Address ___
• Phone Number _____

SAFETY

PLEASE READ all instructions completely before attempting to install or operate the unit. Take particular note of the DANGER, WARNING and CAUTION information in the manual. The information is important for the safe and efficient installation, operation and care of your Perlick unit.

IMPORTANT!
Read and understand all information in this manual before attempting the installation. All plumbing and electrical work must be performed by a qualified technician and conform to all applicable state and local codes.

• DANGER Indicates a hazard that WILL result in serious injury or death if precautions are not followed.
• WARNING Indicates a hazard MAY cause serious injury or death if precautions are not followed.
• CAUTION Indicates a hazard where minor or moderate injury may occur if precautions are not followed.
• NOTICE Indicates that property damage may occur if warnings or instructions are not followed.

Refrigerant

• DANGER Take caution when handling, moving, and using the product to avoid damaging the refrigerant tubing or increasing the risk of a leak.
• WARNING All service work shall be performed by factory-authorized service personnel and all component parts shall be replaced with like components to minimize the risk of possible ignition due to incorrect parts or improper service.
• CAUTION If service is necessary, repair work must be performed by a Perlick-authorized servicer. Work done by unqualified individuals could potentially be dangerous and will void the warranty.
• NOTICE This product contains blown foam insulation using blowing agent R-611 (Methyl Formate). The foam in this product does not contain HFCs, CFCs, or HCFCs.
• All models covered in this user manual are manufactured using refrigerant R600a (Isobutane). R600a is a hydrocarbon.
• This refrigerant is flammable and is only allowed for use in appliances with fulfill the requirements of UL/IEC 60335-1 and UL/IEC 60335-2-24. (To cover potential risk originated from the use of flammable refrigerants). Consequently,
• R600a is only allowed to be used in refrigerating appliances with are designed for this refrigerant and fulfill the abovementioned standard.
• R600a is heavier than air. The concentration will always be highest at the floor level.
• The explosion limits are as follows:
• Lower Limit: 1.8% by volume
• Upper Limit: 8.4% by volume
• Ignition Temperature: 460°C

Prior To Installation

• Carefully inspect cabinet for hidden damage. If damage is discovered, file your claim immediately with the transport company. Perlick is not responsible for damage in transit.
• CAUTION When moving the unit, be sure to protect finished flooring with appropriate material to avoid damage from moving the unit.
• CAUTION Do not lift unit by drawer, shelving or door handles, as damage to the unit could occur if not moved as instructed.
• WARNING To prevent personal injury, a minimum of two people are required to lift the unit. Larger units may require additional personnel. Before moving the unit, secure the door shut with tape to prevent door from swinging open while being moved.
• Carefully move unit to installation site and place in front of opening.
• CAUTION If unit has been laid on its back or sides, place unit upright and allow minimum of 24 hours before connecting power.

WARNING: California Prop 65 Notice

• These products may expose you to chemicals including Chromium, which are known to the state of California to cause cancer and birth defects or other reproductive harm. For more information on whether a product in this list contains these chemicals, please refer to the specific product page at perlick.com. Or to find out more about Prop 65, go to P65Warnings.ca.gov.

TOUCH-SCREEN CONTROL OPERATION

OPERATION

MASTER SWITCH
Signature Series products come equipped with a master power switch located behind the louvered toe kick. Remove the toe kick to turn power on or off to the unit.
ANTI-SWEAT HEATER SWITCH
Signature Series-Dual Zone Freezer Models (HP24Z) come equipped with an anti- sweat heater and switch to enable or disable the heater. The anti-sweat heater prevents condensation from forming on the front face of the cabinet between the top and bottom drawers. Remove the toe kick to access the switch to enable or disable the anti-sweat heater.
The anti-sweat heater switch is located below the master power switch (Figure 1).

INTERIOR LIGHT

• Door units are equipped with an interior light that illuminates when the door is opened. All models come standard with adjustable blue and white LED lighting. The cabinet also comes equipped with a manual light switch for displaying the products through a glass door.
• Always ensure that the manual light switch is in the OFF position before closing a solid wood or stainless steel door. If a manual light switch is left on for an extended period of time, it will increase energy usage and decrease LED life.

LOADING PRODUCT

• Before storing perishables, turn the unit on and allow it to operate for a minimum of 24 hours to allow temperatures to stabilize.
• When loading items into the unit, do not block internal louvers and fan guard openings or performance will be decreased.

CHECKING PRODUCT TEMPERATURE

1. To accurately check the temperature of the product stored in the refrigerated compartment, insert an accurate thermometer into a plastic unbreakable bottle, partially filled with water. Tighten bottle cap securely.
2. Place the bottle in the desired area for 24 hours. Refrain from opening the unit during the testing period. After 24 hours, check the temperature of the water. Adjust the temperature accordingly using the following procedures:

DIGITAL TEMPERATURE CONTROL

Programming Button Definitions:

• SET Button
• DEFROST button (melting snowflake)
• UP Arrow
• DOWN Arrow
• ON/OFF Button
• Signature Series Dual-Zone Control Instructions On/Off
• Press the ON/OFF button to turn the unit on or off.

Upper Compartment:

• To view the upper compartment temperature, press and release the DEFROST button (melting snowflake).

Lower Compartment (Must be the coldest zone):

• The display reading always shows the lower compartment temperature.

Changing the Lower Compartment Temperature:

1. Press and hold the SET button until the display shows St1 with” F” flashing.
2. Press SET again to display the lower compartment’s current temperature (“F” will continue to flash).
3. Use the UP or DOWN arrow key to scroll to the desired temperature. The controller will memorize the new temperature.

Changing the Upper Compartment Temperature:

1. Press and hold the SET button until the display shows St1 with” F” flashing. Press the DOWN arrow once; the display will read St2.
2. Press SET again to display the upper compartment’s current temperature (“F” will continue to flash).
3. Use the UP or DOWN arrow key to scroll to the desired temperature. The controller will memorize the new temperature.

NOTE: Dependent on the model and configuration, the controllers have been programmed to only allow a lower compartment temperature adjustment range as specified within the chart below.
The upper compartment range is not limited, but should always be kept within the specified range shown in the table for the upper compartment. See the chart below for the specified range allowed for your unit.

Signature Series – Dual-Zone Units

Model| Range (F)
HP24Z| Upper 30° – 42°F / Lower -10° – 15°F
HP24C| Upper 45° – 65°F / Lower 33° – 42°F
HP24D| Upper 51° – 65°F / Lower 45° – 55°F

To Start A Manual Defrost (HP24Z Models Only)

• Press and hold the DEFROST button (melting snowflake) for 3-5 seconds. Melting snowflakes will illuminate. 15”, 24” Single Zone, 24” Shallow Depth, and ADA Controls

To Set Target Temperature

• Press and release the SET button. The display will show the current temperature setpoint.

To Change Setpoint Temperature

1. Press and hold the SET button until the display shows the current setpoint temperature with the “F” flashing.
2. Use the UP and DOWN arrow buttons to scroll to the desired temperature.

To Start A Manual Defrost (Freezer Models Only)

• Press the DEFROST button (melting snowflake).

To See the Maximum Stored Temperature

• Press the UP arrow button to see the maximum stored temperature.
• To reset the maximum stored temperature, while displayed, press and hold the SET button until ‘rst’ flashes in the display.

To See the Minimum Stored Temperature

• Press the DOWN arrow button to see the minimum stored temperature. To reset the minimum stored temperature, while displayed, press and hold the SET button until ‘rst’ flashes in the display.

On/Off

• Press the ON/OFF button to turn the unit on or off.
• NOTE: Dependent on the model and configuration, the controllers have been programmed to only allow a temperature adjustment within a specified range. See the chart to the right for the specified range allowed for your unit.

Signature Series – HP15 Models

Model| Min Temp Set| Max Temp Set
HP15R| 33° F| 42° F
HP15B| 33° F| 48° F
HP15W| 45° F| 65° F
HP15T| 33° F| 42° F
Signature Series – HP24 Models
Model| Min Temp Set| Max Temp Set
HP24R| 33° F| 42° F
HP24F| -10° F| 10° F
HP24B| 33° F| 48° F
HP24W| 45° F| 65° F
HP24T| 33° F| 42° F
Signature Series Shallow Depth
Model| Min Temp Set| Max Temp Set
HH24RS| 33°| 42°
HH24BS| 33°| 48°
HH24WS| 45°| 65°
C-Series Models
Model| Min Temp Set| Max Temp Set
HC24RB| 33°| 42°
HC24BB| 33°| 48°
HC24WB| 45°| 65°
ADA-Compliant Series
Model| Min Temp Set| Max Temp Set
HA24FB| -10°| 10
HA24RB| 33°| 42°
HA24BB| 33°| 48°
HA24WB| 45°| 65°

LED Functions

The following table describes LED functions.

• An audible alarm will sound if the door is left ajar for longer than one minute.
• Fully closing the door will clear the alarm condition, prolonged time spent with the door open can damage the equipment.

CARE & MAINTENANCE

MAINTENANCE SEASONAL MAINTENANCE FOR UL-APPROVED OUTDOOR MODELS Winterizing

• This process should occur when the daily low temperatures are at or below the temperatures stated below:
• Freezer models: 32° F
• Refrigerator models: 38° F
• Beverage Center: 42° F
• Wine Reserve: 45° F

It is best to winterize your unit before the low temperatures listed above.

1. Turn the unit to the OFF position by pressing the OFF button on the controller. The controller displays the word “OFF” and, for Signature Series models, turn the master switch located behind the grille off (if the power cord is accessible, unplug the power cord. If not, turn off the circuit breaker to the electrical receptacle the cabinet is plugged into).
2. Remove all contents from the unit.
3. Remove the front grille.
4. Clean the condenser by using a vacuum cleaner to remove loose debris (leaves, dirt, etc.) that may have accumulated inside the grille.
5. Reinstall the front grille.
6. Clean the interior of the unit using stainless steel cleaner and polish.
7. Clean the exterior of the unit using stainless steel cleaner and polish.

NOTE: Do not place a cover over the unit. While not required, you may choose to remove the unit from the outdoor location and store it indoors.

• CAUTION Operating the unit at temperatures lower than those recommended will void the warranty.

Spring Start-Up

• This process should occur after the daily low temperatures is above the temperatures stated below:
• Freezer models: 32° F
• Refrigerator models: 38° F
• Beverage Center: 42° F
• Wine Reserve: 45° F

1. Remove the grille.
2. Check the condensing unit to ensure it is clear of loose debris, and clean as necessary with a vacuum cleaner.
3. Reattach front grille to the unit.
4. Clean the interior of the unit using stainless steel cleaner and polish.
5. Clean the exterior of the unit using stainless steel cleaner and polish
6. Plug the unit into the electrical receptacle or turn on the circuit breaker.
7. Turn on the master switch located behind the grille if model is Signature Series. Press the OFF button one time to turn the unit on. The controller display will show the actual temperature inside the cabinet.
8. The cooling process will begin to bring the unit to the set temperature. It’s recommended you run the unit for 24 hours to stabilize the operating temperature before using it.

DANGER Never attempt to repair or perform maintenance on the unit until the main electrical power to the unit has been disconnected!

LED REPLACEMENT

• Call your Perlick Factory Authorized Service Center. For the location of the Service Center in your area, contact your selling dealer, inquire via the web at www.perlick.com, E-mail us at warrantyserv@perlick.com, or call 800-558-5592 during normal business hours.

DISPOSAL

• Risk of child entrapment. Before you throw away your old refrigerator or freezer:
• Take off the doors.
• Leave the shelves in place so that children may not easily climb inside.

STAINLESS STEEL CARE & CLEANING General

• Stainless steel is a “passive” metal because it contains other metals like chromium, nickel and manganese that stabilize the atoms. Chromium provides an invisible passive film that covers the steel surface, acting as a shield against corrosion. As long as the film is intact and not contaminated, the metal is passive and stainless. If the passive film of stainless steel has been broken, equipment can start to corrode and rust.
• Three materials or processes can break down stainless steel’s passive layer and allow corrosion to occur:
• Mechanical abrasion
• Deposits and water
• Chlorides
• Mechanical abrasion refers to items that will scratch a steel surface. Steel pads, wire brushes and scrapers are prime examples.
• Water comes out of the faucet in varying degrees of hardness.
• Hard water may leave spots. When allowed to sit, these deposits will break down the passive chromium layer and rust stainless steel. Other deposits from food preparation must be promptly removed with an appropriate cleaning agent.
• Chlorides are found nearly everywhere. They are in water, food, and table salt. Household and industrial cleaners are the worst offenders.

Preventing Stainless Steel Rust

• Use non-abrasive tools to clean stainless steel products. Soft cloths and plastic scouring pads will not harm the steel’s passive layer.
• Clean with polish lines. Some stainless steels have visible polishing lines or “grain”. When visible lines are present, always scrub in a motion parallel to the lines. When the grain cannot be seen, polish in a consistent straight pattern and not in a circular motion.
• Use alkaline, alkaline chlorinated, or non-chloride-containing cleaners. While many traditional cleaners are loaded with chlorides, the industry is providing an ever-increasing choice of non-chloride cleaners. If you are not sure of the chloride content in the cleaner being used, contact your cleaner supplier. If your present cleaner contains chlorides, ask your supplier for an alternative. Avoid cleaners containing quaternary salt; it also can attack stainless steel and cause pitting and rusting.
• Keep food equipment clean. Use alkaline, alkaline chlorinated or non-chloride cleaners at recommended strength. Clean frequently to avoid build-up of hard, stubborn stains. The single most likely cause of damage is chlorides in the water.
• Remember, adding heat to cleaners that contain chlorides dramatically increases their effect on stainless steel.
• If chlorinated cleaners are used, immediately rinse and wipe equipment and supplies dry. The sooner you wipe standing water, especially when it contains cleaning agents, the better.
• After wiping equipment down, allow it to air dry. Oxygen helps maintain the stainless steel passive film.

Cleaning the Cabinet Interior/Exterior

• CAUTION NEVER use hydrochloric acid (muriatic acid) on stainless steel. Do not use abrasive cleansers or cloths on any interior or exterior surfaces or removeable parts.
• Glass panels may be cleaned using any standard glass cleaner available on the market.
• To clean interior and exterior non-metallic surfaces and removable parts, wash with mild solution of soap and lukewarm water with a little baking soda. Rinse and dry thoroughly.
• Avoid getting water on the lights, controllers, fan motors and unfinished wood wine rack faces.

Cleaning the Condenser

• The condenser (located behind the front grille cover) should be cleaned every three (3) months. Use a soft bristle brush and vacuum to remove dust and lint.
• Flammable Refrigerant. Risk of fire or explosion. Do not damage refrigeration tubes.
• CAUTION Avoid damaging or crushing the condenser fins or tubing.

Provides barrier film to minimize fingerprints. Can be used on all finishes. Rub the surface with a cloth as directed on the package.
Stubborn stains and discolorations| AllChem Concentrated Cleaner, Samae, Twinkle, Cameo Copper Cleaners, Grade FFF Italian Pumice Whiting, Steel Bright, Lumin Cleaner, Zud Restoro, Sta-Clean, Highlite Cooper’s Stainless Steel Cleaner or Revere Stainless Steel Cleaner| Apply with a damp sponge or cloth, then rinse with clear water and wipe dry.
Old Dutch, Lighthouse Sunbrite, Wyandotte Bab-O, Gold Dust, Sapollo, Bon Ami or Comet| For these household cleaners, rub with a damp cloth. They may contain chlorine bleaches so rinse thoroughly after use and wipe dry.
Liquid NuSteel or Dubois Temp| For these products, rub the surface with a dry cloth using only a small amount of cleanser. Rinse with water and dry.
Heat tint or heavy discoloration| Penny-Brite, Copper Brite, Paste Nu-Steel, Dubois Temp or Tarnite| Rub onto surface with a dry cloth
 | Bar Keepers Friend, Revere Stainless Steel Cleaner, Allen Polish, Steel Bright Wyandotte Bab-O or Zud| When using these cleaners, apply with a damp sponge or cloth, rinse thoroughly and wipe dry.
Tenacious deposits, rust, discoloration, industrial atmospheric stains| Oakite No. 33 Dilac, Texo NY,  Flash-Klenz Caddy Cleaner, Turco Scale 4368 or Permag 57| Swab and soak with a clean cloth. Let stand for 15 minutes or more according to directions on package, then rinse and wipe dry.
Rust dicoloration or corrosion caused by cleaning agents containing hydrochloric (muriatic) acid or chlorine bleach| 3M Scotch Pad, type A, grade “fine”| Clean off the surface soil using cleaning methods above. Then rub discolored or corroded areas lightly with a dry pad.
Use of property names is intended only to indicate a type of cleaner and does not constitute an endorsement. Omission of any proprietary cleaner does not imply its inadequacy. All products should be used in strict accordance with instructions on the package.

_NOTE: Do NOT use steel wool or scouring pads to clean stainless steel._

For Product Information

• Contact your selling dealer
• Inquire via the web at perlick.com/residential-design-solutions
• Call 800-558-5592 for factory assistance on planning installation or product information
• Write to Perlick Corporation, Customer Service Department, 8300 West Good Hope Road, Milwaukee, WI 53223
• Email us at warrantyserv@perlick.com

For Product Service

• Check the model and serial number of your unit located on the label attached to the inside top of the cabinet.
• Inquire via the web at www.perlick.com, or call 800-558-5592.

For Replacement Parts and Accessories

• Use only genuine Perlick replacement parts and accessories. Genuine Perlick parts and accessories are designed to work correctly with Perlick products and offer superior service life. The use of non-Perlick parts can damage the unit and may void the warranty.
• Check the model and serial number of your unit located on the label attached to the inside top of the cabinet. Call your Perlick Factory Authorized Service Center.
• Inquire via the web at www.perlick.com, or call 800-558-5592.

TROUBLESHOOTING

• If the unit appears to be malfunctioning, read through the OPERATION section of this manual first. If the problem persists, check this troubleshooting section to see if you can refer to the cause and remedy of the problem and resolve it without a service call.
• DANGER Never attempt to repair or perform maintenance on the unit until the main electrical power to the unit has been disconnected!

Technical Service at 800-558-5592
Light stays on when door switch is closed| Manual switch is on| •         Turn manual switch off
 | Door is not making contact with the door switch| •         Makre sure the door closes tightly
Noisy operation| Soft sounds from compressor, fan motor and valves heard| • Normal operation
“Crackling” sound during defrost| •         Normal operation
LED Controller display is flashing ”P1”| Thermostat probe has failed| • Contact Perlick Technical Service at 800-558-5592
LED Controller display is flashing “P2”| Evaporator probe has failed| • Contact Perlick Technical Service at 800-558-5592
LED Controller display is flashing “HA”*| Internal compartment has exceeded the high temperature alarm preset value for over 30 minutes.| •         Make sure the door is completely closed.

•         Check the door gasket seal. Replace if necessary.

•         Check the condenser and clean it if necessary.

•         Make sure the louvered plate is unobstructed. If surrounding ambient temperature has recently changed dramatically, the compartment may be affected.

•         Make sure the interior light is off.

•         Warm product was recently placed in the cabinet. Wait 24 hours for the product to chill and then recheck the temperature.

LED Controller display is flashing “LA”| Internal compartment has exceeded the low temperature alarm preset value for over 30 minutes.| •         Make sure the door is completely closed.

•         Check the door gasket seal. Replace if necessary.

•         If the surrounding ambient temperature has recently changed dramatically, the compartment temperature may be affected.

LED Controller display is flashing “dA”| Door is open.| •         Make sure the door is completely closed.
Unit is not running| No power is going to the unit.| •         Home circuit breaker was tripped. Reset the circuit breaker.

•         ON/OFF keypad is turned off. Turn it on.

•         If it is a Dual-Zone model, check the Dual- Zone power switch (see page 4).

Condenser is dirty.| •         Clean the condenser
Problem| Cause| Solution
---|---|---
Compartments are warmer than usual| Control preset is set to warm| • Lower the setpoint temperature. Refer to changing the set point for the specific model
Light is staying on| •         Turn the manual light switch off.
Condenser is dirty or obstructed| •         Clean the condenser and clear obstruction.
The door is open or has been opened more frequently lately.| •         Wait 24 hours and recheck the temperature.
Internal louvers and/or the fan guard is obstructed.| •         Reset the preset temperature if necessary

– refer to page 5 and 6 of this guide.

•         Make sure the louvers and/or the fan are not obstructed.

Warm product product was recently placed in the cabinet.| •         Wait 24 hours for product to chill, then recheck the temperature.
System runs for a long period of time.| Condenser is dirty or obstructed.| • Clean the condenser and clear the obstruction.
Door was kept open for a long time or was opened more frequently, or warm product was recently placed in the cabinet.| •         Wait 24 hours and recheck temperature.
Hot day and warm room temperature| •         Normal for the system to run more frequently.
Condensation forms outside of the unit| High humidity and/or frequent door opening| •         Normal Operation
Condensation forms inside the compartments| High humidity and/or frequent door opening| •         Normal operation
 | The door is not closing and sealing properly| •         Make sure the door is closing properly. Check the door seal and replace if necessary.

•         If condensation persists, contact Perlick Technical Service at 800-558-5592

• © 2023 Perlick Corporation
• perlick customer service (800)558-5592
• www.perlick.com

Documents / Resources

| Perlick HH24RO42L Residential Undercounter Refrigeration [pdf] User Guide
HH24RO42L, HH24RO-4-2L, HH24RO42L Residential Undercounter Refrigeration, Residential Undercounter Refrigeration, Undercounter Refrigeration, Refrigeration
---|---

References

• P65Warnings.ca.gov
• Perlick Corporation - Commercial Refrigerator and Bar Equipment Supplier - Perlick Corporation
• Residential Design Solutions - Perlick Corporation
• Perlick Corporation - Commercial Refrigerator and Bar Equipment Supplier - Perlick Corporation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>