BASS JAXX CIRCUIT True Wireless Earbuds Instruction Manual
- June 12, 2024
- BASS JAXX
Table of Contents
BASS JAXX CIRCUIT True Wireless Earbuds
Thank you for purchasing the Circuit True Wireless Earbuds. This manual provides more information about wireless earbuds, please read the instructions before using them.
Product Overview
Remove the protective stickers before using
- Touch Control On/Off Button/ Play/ Pause Music/ Answer/End Call
- LED Light-up
- Built-in Microphone
- IPX4 Water Protection Earbuds
- Charging Case Battery Level Indicator
- Earbuds Battery Level Indicator
- USB Type-C Charging Port
Package Contents
Includes
- 1(One) Pair Earbuds 1.7in. x 1.5in. x 1.0in. (4.4cm x 3.7cm x 2.6cm) each
- 1(One) Portable Charging Case 3.3in. × 2.3 in. x 1.3 in. (8.4cm x 5.8cm x 3.2cm)
- 1(0ne) USB-C Charging Cable 11.8in. (30cm)
- 1(One) Instruction Manual
Specifications
- Driver Diameter: 10 mm
- Impedance: 32 Ohms
- Frequency Response: 20 Hz – 20 kHz
- Sensitivity: 96 dB +/- 3 dB
- Power Supply: Li-ion Battery 3.7V 35 mAh Per Earbud
- Playtime: 10 Hours
- Charging Time: 2 Hours
- Bluetooth Range: 32.8 Feet
- Bluetooth Version: 5.3
- Charging Case Battery Capacity: 300 mAh
- USB Type-C Charging Cable Included
Power On/Off
Power On will flash.
Power Off will turn off.
Press and hold down the ON/OFF Button of the earbuds for 3 seconds and the LED Press and hold down the ON/OFF Button of the earbuds for 4 seconds and the LED Pair the wireless earbuds with your mobile device
- Keep the distance between the earbuds and mobile device within 32.8 feet.
- Deactivate the Bluetooth function on your mobile device.
- The protective stickers must be removed from the earbuds and put the earbuds back to the charging case before use. T
- ake both earbuds out of the charging case and wait for 3 to 5 seconds for auto pairing. The earbud has an indicator blinking in White. Another earbud will stop blinking when auto pairing is done successfully.
- Activate the Bluetooth function on your mobile device and select CIRCUIT TWS* from the list shown.
- After pairing is successful, both earbuds’ LEDs will stop blinking.
Attention
If the auto-pairing is not successful, manual pairing between earbuds is
essential by following below procedures:
- Make sure the earbuds are charged.
- Deactivate the Bluetooth function on your mobile device. (if you had paired the earbuds to some other mobile device(s) nearby, please be sure to de-activate those device(s) too).
- Power on both earbuds simultaneously by pressing the ON/OFF buttons for 3 seconds and wait for 3 to 5 seconds for auto pairing. (Keep the Bluetooth function off on your mobile device before this operation.)
- Activate the Bluetooth function on your mobile device and select CIRCUIT TWS” from the list shown.
- After pairing successfully, both earbuds’ LEDs will stop blinking.
Reconnect the wireless earbuds to your mobile device When powered on, the wireless earbuds will automatically connect with the last successfully paired device. Disconnect the wireless earbuds from your mobile device Power off the wireless earbuds, or Switch off the Bluetooth on your mobile phone, or Leave the earbuds 60ft away from your mobile phone or further.
Answer / Reject a call
When receiving a call, press the ON/OFF Button once ( on either earbud) to
accept the call, or answer the call normally via your mobile phone. Press and
hold 2 seconds to read it.
End a call
To end the call, just press the ON/OFF button at any side of the earbud with a
Beep sound to end it.
Functions
Pause / Play Music: Short Press on the ON/OFF Button Go back to the previous
song: Double click the left ON/OFF button. Advance to the next song: Double-
click the right ON/OFF button. Voice Assistant: Press and hold the ON/OFF
button for 2 seconds.
Charging your Earbuds
- Open the charging case cover.
- Remove the protective stickers between the earbuds and the charging case.
- Insert the Earbuds into the charging case.
- The earbuds will start the charge automatically.
- The LED indicator light of the Earbuds will be turned on when charging.
- Once fully charged, the LED will be off.
Note: If the charging is not started, take out both earbuds from the charging case and insert again after a few seconds.
Recharge Charging Case
For your safety, please always use the appropriate 5V output charger/Adapter
to charge the product. DO NOT USE Quick Charging USB Adapter to charge the
product, as it might damage the product.
-
Use the USB Type-C charging cable provided with the packaging.
-
Connect the USB plug to a USB port on a computer or wall adapter, then connect the USB Type-C plug to the USB Type-C charging port on the charging case to begin charging
-
The last digit of the Battery Level Indicator will be flashing during charging
-
Once fully charged, the Battery Level Indicator will stop flashing.
-
The Earbuds Battery Level Display will be flashing during the earbuds are charging and will be off after fully charged.
NOTE:- You must select a qualified charger from a regular manufacturer.
- You must charge the charging case and earbuds if it has been not used for more than 6 months.
CAUTION: The USB Type-C charging cable included with this item is intended for use with this product. Only use the included USB Type-C charging cable to charge this product.
FAQ
If the wireless earbuds cannot be paired with your device, please try the following: Ensure that your earbuds are in pairing mode or reconnection mode Ensure that the Bluetooth search function of your mobile device is activated. If the wireless earbuds will not turn on: Make sure the earbuds are fully charged. Make sure the protective stickers are removed from the Earbuds
Can I change the battery for the earbuds and the charging case?
The wireless earbuds and the charging case use a built-in non-detachable
battery which cannot be removed. If the charging case cannot be recharged: If
you use a power outlet, ensure that the power supply is connected securely and
the outlet works. If you use a computer, ensure that it is connected and the
USB port is powered. Safety instructions for the lithium battery and charging
the product The input voltage to the product is 5V 1A. In order to charge the
product in a safe manner and reliable conditions, please only adopt a
certified appropriate charger/ adapter for charging the product. Only charge
the product at ambient temperatures between 10 °C/ 50 °F and 40 °C/104 °F.
- Do not heat above 70 °C/158 °F, eg. Do not expose to sunlight or throw into fire.
- Switch off the product after use.
- Please note that we won’t take any responsibility for any wrong operation (eg.
- Voltage higher than 5) as this may result in severe injury or loss of property, and we cannot control the operating process during the time the user using this product.
- In extreme cases, abuse or misuse of Lithium battery packs can lead to an explosion, heat generation, fire development, or smoke development.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operations. Changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
FCC ID: 2ADM5-EP-0692
seep all relevant information for future reference
ITEMS EP-0692
Distributed by 1616 Holdings, Inc.
701 Market Street, Suite 200
Philadelphia, PA 19106
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>