NEUATION iSWIX FS Fixed Speed Vortex Mixer User Manual
- June 12, 2024
- NEUATION
Table of Contents
FS Fixed Speed Vortex Mixer
ISWIX FS
PRODUCT USER MANUAL
INTRODUCTION
This vortex mixer is designed for laboratory mixing. It assures the highest performance in terms of speed, reliability, precision and safety.
INTENDED USE
This vortex mixer is a general laboratory vortex mixer. It is indented for application where vortexing of single or multiple tubes is required.
FEATURES
- Continuous / touch operation
- Long life AC motor with ball bearing
- Inbuilt counter balance for steady and safe operation
- Orbital diameter of 4mm
- Robust construction for stable operation
- Silent operation
- Universal power supply
TECHNICAL SPECIFICATIONS
| Orbital Diameter | 4 mm |
|---|---|
| Maximum Speed | 2800 RPM |
| Speed Accuracy | ± 5% |
| Maximum Load Capacity | 500 gm |
| Different modes | Continuous & Touch mode |
| Protection Rating | IP 21 |
| Ambient Temperature | 5 to 40 °C |
| Permissible Relative Humidity | .AO% |
| Dimensions (W x D x H) | 205 x 138.5 x 136 mm |
| Weight | 2.8 Kg |
| Power Supply | 230VAC, 50Hz |
| Power Consumption | 70 W |
| Altitude | Use upto an altitude of 2000 m above MSL |
| Pollution Degree | 2 |
| Environment | For indoor use only |
| Safety Fuse | 1 Amp |
STANDARD ACCESSORIES
- Standard cup head (pre-installed) + round disk attachment
- Power cord, Product user manual & warranty card
SAFETY PRECAUTIONS
**** Read the following safety instructions before using LN the mini vortex mixer for your safety & the safety of the equipment.
- Do not use the unit if it shows any sign of electrical or mechanical damage.
- Do not use the vortex mixer in hazardous atmosphere or with hazardous material for which the unit is not designed.
- Always use the vortex mixer on a level & stable surface for best performance and maximum safety.
- Position the device appropriately to prevent the disconnection of the power supply.
- Do not the lift vortex mixer with the attachments, as every attachment including the cup head are designed to be pulled off for interchanging.
- Do not rotate or give full rotation to the attachments (cup head, universal attachment, etc) attached to the modified shaft body.
- Clean the unit with a damp cloth using a mild detergent only. Do not use chemical cleaning agents.
- If liquid is spilled on the unit, first disconnect unit from the external (main) power supply and then clean the unit with damp cloth.
- Do not use accessories which are not recommended by the manufacturer, as this may affect performance.
- The instrument is designed to be used in the laboratory environment.
- Liquid spillage may harm the unit. Do not fill microtubes, while they are attached to the vortex mixer.
- For Safety we have provided protective earthing with the power supply. Make sure the power supply is earthed.
- Safety Fuse is provided with a 1 Amp configuration which can be replaced by the operator. The same will protect the machine circuit during electrical faults or overloads.
STANDARD PART LISTING
INSTALLATION
Open the box, open the inner packaging and gently take the vortex mixer out of
the box. Before the first use ensure that all the packaging is removed and the
cup head is firmly tightened before using the product. The user manual and
accessories should be kept near the unit for warranty purposes.
Take the unit out and place it on the levelled & stable surface near the
grounded electrical outlet. Keep a clearance of 10 cm on all sides of the unit
for proper ventilation.
Connect one end of the power adaptor pin to the rear side of the unit and
another end to main supply. Make sure that the main switch is not switched
“ON” until the adaptor is connected to both the side.
USER INTERFACE & DISPLAY
| No. | Name/Symbol | Function |
|---|---|---|
| 1 | Power LED | Power Led showing the status of vortex action. Glowing – when |
vortex action is in process, Not Glowing – No Vortex action
2| 3 way switch (Mode selection)| Rocker switch is use to select different
mode in vortex mixer. OFF (stand by), Continuous & touch operation mode.
OPERATION
Always connect the plug to the power supply to start the unit
STANDBY, TOUCH & CONTINUOUS MODE
Placing the 3 way switch in the Standby position It will keep the vortex mixer
in an OFF state.|
---|---
Press the 3 way switch up towards the “Touch ” side to enable the Touch mode.
In Touch mode, vortex action will start only when the cup head Is press.|
Press the 3 way switch down towards the “ON” side to enable the Continuous
mode. In Continuous mode, the vortex action will start automatically (without
pressing cup head) at the set speed and time.|
MAINTENANCE & CLEANING
-
Always keep the vortex mixer & its accessories in a safe storage location and clean periodically with moist cloth. After cleaning, ensure that all parts are dry before reuse
-
Ensure that while cleaning the unit is not plugged in.
-
The brushless motor in the vortex mixer requires no routine maintenance. Any required service should be performed by authorized, qualified personnel only.
Repairs performed by unauthorized personnel may void the warranty. -
Do not try to pull the vortex mixer with attached accessories.
-
Do not try to rotate the attachments attached to modify the shaft body.
-
Do not use the vortex mixer & its accessories in direct sunlight or under water.
WARRANTY STATEMENT
This product is warranted to be free from defects in material and workmanship
for a period of two (2) years from date of purchase. Your product will be duly
repaired upon prompt notification in compliance with the following conditions
: This warranty is valid only if the product is used for its intended purpose
and within the guidelines specified in this instruction manual. This warranty
does not cover damage caused by accident, neglect, misuse, improper service,
natural forces or other causes not arising from defects in original material
or workmanship. This warranty does not cover any incidental or consequential
damages, commercial loss or any other damages from the use of this product.
All items returned for service should be set postage prepaid in the original
packaging or other suitable carton, added to avoid damage.
This warranty Is valid only if the warranty is registered with the supplier
within 30 days from the date of purchase.
For your reference, make a note of the serial number, date of purchase and
supplier here.
Serial No…………………………………
Purchase Date…………………………
Supplier…………………………………
PRODUCT DISPOSAL
In case the product is to be disposed of, the relevant legal regulations are
to be observed.
Information on the disposal of electrical and electronic devices in the
European Community The disposal of electrical devices is regulated within the
European Community by national regulations based on EU Directive 2012/19/EU on
waste electrical and electronic equipment (WEEE). According to these
regulations, any devices supplied after 13.06.05 in the business to business
sphere, to which this product is assigned, may no longer be disposed off in
municipal or domestic waste. They are marked with the following symbol to
indicate this.
As disposal regulations within the EU may vary from country to country, please
contact your supplier if necessary.
Accumax Lab Devices Private Ltd.
Plot No. 15, 16 & 32 GIDC Electronic Park SEZ, Sector 26, Gandhinagar,
Gujarat, India – 382026.
Website: www.neuation.com
0210-00-0000-02-003-RO
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>