DPR Label Accessories for OKI Pro1050 Label Printer User Manual

June 4, 2024
DPR

USER MANUAL
Label Accessories
for OKI Pro1050 Label Printer
LABEL REWINDER
INLINE MATRIX REMOVER
IRON TABLEDPR Label Accessories for OKI Pro1050 Label Printer -
icon

Please keep the original packaging in case you need to return the unit.
If we receive the system in non-original packaging, the warranty may be void.

INSTALLATION OF CORE HOLDER

DPR Label Accessories for OKI Pro1050 Label Printe

STEP 1
Install the outer disc (if necessary)DPR Label Accessories for OKI Pro1050
Label Printe - CORE HOLDER

STEP 3
Insert an outer disc.DPR Label Accessories for OKI Pro1050 Label Printe -
CORE HOLDER 1

STEP 4
Screw the knob in order to tighten the roll.
Then lay the core holder onto the core holder supports.
IMPORTANT:
The core holder must be positioned with the black matching handle and gray matching handle.DPR Label Accessories for OKI Pro1050 Label Printe - CORE
HOLDER 2

Label Rewinder
A switching power supply, input of 1,8A 100-240Vac, 50-60Hz output of 24V 2.5A, allows an electronic circuit to adjust the speed of rotation through the tension arm. A 2A fuse is used as system protection.
ATTENTION:
Due to the media cutting after each job printed by OKI printer, it is required first to “feed” enough media necessary to load the rewinder. Once the media is loaded properly, the system is ready to work.

HOW TO INSTALL THE PRINTER PLATE

DPR Label Accessories for OKI Pro1050 Label Printe - CORE HOLDER
13

STEP 1
To get the rewinder aligned with the printer, match the triangles on the second plate with the one on the label rewinder.DPR Label Accessories for
OKI Pro1050 Label Printe - CORE HOLDER 14

STEP 2
Lock the printer plate onto the printer and fix the knob on the rewinder.
PAPER PATHDPR Label Accessories for OKI Pro1050 Label Printe - CORE
HOLDER 5

STEP 1
Pull the media under the tension arm and attach it to the cardboard core. Switch on the unit. The label rewinder is ready.
WORKING CONDITIONS

  • When the printer forwards the media for printing, the tension arm goes down, the device rewinds the printed media.
  • When the unit is operating but the media is not loaded or it runs out, the tension arm reaches the lowest position and after a few seconds, the rewinder’s rotation will be stopped while both leds blink and it beeps.

CONTROL PANEL

DPR Label Accessories for OKI Pro1050 Label Printe - CORE HOLDER
6

ON-OFF
Push this button to turn On or Off the unit.
INCREASE SPEED
Push this button to increase the rotation speed.
DECREASE SPEED
Push this button to decrease the rotation speed.
LABEL FACE-OUT
Turn the unit off. Keep pushing the “FACE OUT” button, and push and release the “ON-OFF” button while the green led turns on and off. The unit is now ready to operate.
LABEL FACE-IN
Turn the unit off. Keep pushing the “FACE IN” button, and push and release “ON-OFF” button while the yellow led turns on and off. The unit is now ready to operate.

HOW TO INSTALL THE PRINTER AND THE LABEL REWINDER ONTO THE TABLE

ATTENTION: In this configuration, the printing plate is not required to be installed. DPR Label Accessories for OKI Pro1050 Label Printe - CORE
HOLDER 26

Install the rewinder and the printer onto the table. Thanks to its custom design, the correct alignments are guaranteed without the need for a second plate.
Inline Matrix Remover
A switching power supply, input of 1.8A 100-240Vac, 50-60Hz output of 24V 2.5A, allows an electronic circuit to adjust the speed of rotation through the tension arm. A 4A fuse is used as system protection.
ATTENTION:
Due to the media cutting after each job printed by OKI printer, it is required first to “feed” enough media necessary to load the matrix remover. Once the media is loaded properly, the system is ready to work.
WARNING:
Before starting a new job, always make sure the waste matrix from the previous job has been removed. Do not attach the matrix from a different size label to an existing roll. This will cause an uneven wrap which will cause the material to walk.
INSTALLATION OF CORE HOLDER

DPR Label Accessories for OKI Pro1050 Label Printe - CORE
HOLDER9

Load a cardboard core onto the core holder to receive the waste.
Tighten using the tension knob.DPR Label Accessories for OKI Pro1050 Label
Printe - CORE HOLDER 10

Insert the empty cardboard core on the core holder to receive the new labels roll.
Load the outside disk making sure it adheres to the cardboard.
Tighten using the tension knob.
HOW TO INSTALL THE PRESSING ROLLERDPR Label Accessories for OKI Pro1050
Label Printe - CORE HOLDER 11

The pressing roller facilitates the matrix removal from the die-cut roll.
Remove it from the rewinder station (there are 4 knobs to unscrew).DPR Label
Accessories for OKI Pro1050 Label Printe - CORE HOLDER
12 How to install:

  1. Unscrew the 10 screws on the top of the matrix remover module.
  2. Position the matrix remover roller onto the matrix remover module and secure it properly with the 10 screws/knobs.

HOW TO INSTALL THE PRINTER PLATEDPR Label Accessories for OKI Pro1050
Label Printe - CORE HOLDER3

STEP 1
To get the inline matrix remover aligned to the printer, match the triangles on the second plate with the ones on the matrix remover.DPR Label
Accessories for OKI Pro1050 Label Printe - CORE HOLDER4

STEP 2
Lock the printer plate onto the printer and fix the knob on the matrix.

PAPER PATH

DPR Label Accessories for OKI Pro1050 Label Printe - CORE HOLDER
15

STEP 1
Pull the media under the tension arm.DPR Label Accessories for OKI Pro1050
Label Printe - CORE HOLDER 16

STEP 2
Paper path.

DPR Label Accessories for OKI Pro1050 Label Printe - CORE HOLDER
17DPR Label Accessories for OKI
Pro1050 Label Printe - CORE HOLDER 18

STEP 3
Pull the media underneath the last aluminum roller then separate the waste matrix from the liner.DPR Label Accessories for OKI Pro1050 Label Printe -
CORE HOLDER 20

STEP 4
Attach the waste matrix to the empty core on the wasted core. DPR Label
Accessories for OKI Pro1050 Label Printe - CORE HOLDER
19

STEP 5
Attach the finished printed media to the empty core on the rewinder core.DPR
Label Accessories for OKI Pro1050 Label Printe - CORE HOLDER
21

STEP 6
Loose media roll.

DPR Label Accessories for OKI Pro1050 Label Printe - CORE HOLDER
23DPR Label Accessories for OKI
Pro1050 Label Printe - CORE HOLDER 22

STEP 7
Release the pressing roller.
Switch on the unit. The matrix remover is ready.
ATTENTION: In this configuration, the printing plate is not required to be installed.

Insert the extension part (TBLEXT) in the slot of the table then fix it with the four screws.DPR Label Accessories for OKI Pro1050 Label Printe - CORE
HOLDER 25DPR Label
Accessories for OKI Pro1050 Label Printe - CORE HOLDER7

Install the matrix remover and the printer onto the table. Thanks to its custom design, the correct alignments are guaranteed without the need for a second plate.

SENSOR CALIBRATION (INLINE MATRIX REMOVER)
STEP 1. UNIT OFF. Insert a small needle into the hole present on the cover and keep pushing the button while switching on the device; the yellow led is flashing.
STEP 2. Keep the tension arm in the low position and push again the button, both leds are flashing.
STEP 3. Move the tension arm at the maximum high position and press the button 2 times, the core holder starts to rotate. the first time the green led flashes, and the second time the led are both ON.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals