Teracom Product Name TSM400-1-TH Model Number TSM400-1-TH TSM400-1-TH 1 Wire Temperature and Humidity Sensor User Manual

June 9, 2024
Teracom Product Name TSM400-1-TH Model Number TSM400-1-TH

TSM400-1-TH 1-Wire temperature and humidity sensor Version 1.2 / March 2023

Teracom Product Name TSM400-1-TH Model Number TSM400-1-TH TSM400-1-TH 1 Wire
Temperature and Humidity Sensor USER MANUAL
www.teracomsystems.com

Short description

TSM400-1-TH is a temperature and humidity sensor that supports the 1-Wire protocol. A unique capacitive element is used for measuring relative humidity while the temperature is measured by a band gap sensor. Both sensors are seamlessly coupled to a 12-bit analog to digital converter. This results in superior signal quality.
The TSM400-4-TH sensor is housed in a slim plastic enclosure. The bottom part of the enclosure is suitable for installation on standard flush-mounted/cavity wall boxes ø68mm, with installation openings on 61 mm.

Features

  • LED indicator for status of communication
  • Excellent long-term stability
  • Firmware update with Teracom controller via the 1-Wire interface

Applications

  • Environmental quality monitoring and assessment for offices.
  • Humidity and temperature monitoring in building management systems.
  • Smart ventilation systems.

Specifications

  • Physical characteristics
    Dimensions: 81 x 81 x 30 mm
    Weight: 66 g

  • Environmental limits
    Operating temperature range: -20 to 60°C
    Operating relative humidity range: 10 to 90% (non-condensing) *
    Long term drift typical: ±0.25 %RH/year, ±0.05 °C /year **
    Storage temperature range: -20 to 60°C
    Storage relative humidity range: 10 to 90% (non-condensing)
    Ingress protection: IP20

  • Power requirements
    Operating voltage range (including -15/+20% according to IEC 62368-1): 4.5 to 26 VDC
    Current consumption: 10 mA@5VDC

  • Humidity measurements
    Accuracy (min): ±3.0 %RH (in 20 to 80 %RH range)
    Accuracy (max): ±5.0 %RH (in 10 to 90 %RH range) *
    Resolution: 0.1 %RH

  • Temperature measurements
    Accuracy (min): ±0.4 °C (in -10 to +60°C range)
    Accuracy (max): ±0.6 °C (in -20 to +60°C range)
    Resolution: 0.1 °C

  • Warranty
    Warranty period: 3 years

  • Recommended operating range is 20% to 80% RH (non-condensing) over –10 °C to 60 °C Prolonged operation beyond these ranges may result in a shift of sensor reading, with slow recovery time.
    ** Higher drift values might occur due to contaminant environments with vaporized solvents, out-gassing tapes, adhesives, packaging materials, etc.

Pinout

| Pin| Description| UTP wires color
---|---|---|---
1-W| 1-Wire data| Green
+5÷30V| Positive power supply| Orange
GND| Ground (negative) supply| Green/White tracer
Orange/White Tracer
A+| Not used|
B-| Not used|
TERM| Not used|

Installation

It is strongly recommended to use UTP/FTP cables and daisy-chained (linear) topology for multiple sensors and keep the total cable length up to 30 meters.

Teracom Product Name TSM400-1-TH Model Number TSM400-1-TH TSM400-1-TH 1 Wire
Temperature and Humidity Sensor - Fig 2

“Star” topology can be used only as a last resort for up to 4 sensors and a total cable length of up to 10 meters.

Teracom Product Name TSM400-1-TH Model Number TSM400-1-TH TSM400-1-TH 1 Wire
Temperature and Humidity Sensor - Fig 3

Status indicator

The status of the device is shown by a single LED, located inside the box:

  • If the LED blinks for a period of 1 second, the sensor works properly;
  • If the LED blinks for a period of 3 seconds, there isn‘t communication with the controller;
  • If the LED doesn’t blink, there isn’t a power supply.

Installation tips

The location and the mounting position of sensors have a direct effect on the accuracy of the
measurements. The tips below will ensure good measuring results:

  • The sensor shall be installed about 1.2-1.4 m above the floor;
  • To avoid solar radiation, the sensor should not be installed next to windows or directly in the sunlight;
  • The sensors shall be installed in a place with sufficient air circulation.

1-Wire is a registered trademark of Maxim Integrated Products, Inc. It is strongly recommended to read Maxim’s 1-Wire tips at https://teracomsystems.com/wp-content/uploads/AN148.pdf .
TSM400-1-TH sensor is intended for installation on a cavity wall box with 68mm diameter and 61 mm screw spacing.

Firmware update

The firmware of the sensor can be updated with any Teracom controller which supports a 1-Wire interface. For more details ask your dealer.

Recycling

Recycle all applicable material.
Do not dispose of regular household refuse.

TSM400-1-TH_R1.2 – March 2023

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals