saxby lighting 54479 Noble Bathroom Flush Ceiling Light Instruction Manual
- June 12, 2024
- saxby lighting
Table of Contents
Instruction manual
Noble Bathroom Flush
54479, 54487
54479 Noble Bathroom Flush Ceiling Light
Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and satisfactory operation of this product. Please retain these instruction for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building
Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge. If you are in any doubt, please consult a
qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
This system contains non-replaceable parts and cannot be serviced. If damage
occurs the part should be scrapped.
Take care not to drill into any pipes or mains cables beneath the surface
during mounting holes preparation.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will
reach the distances between the junction box and the light fitting.
Avoid locating any cables in positions that would cause a hazard. Position
cables and junction boxes (not supplied) away from areas where they may be at
risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross section area of 1.0mm 2 .
Cables must be protected using suitable conduit or plastic trunking.
This product can be ceiling or wall mounted.
This product has special protection against the ingress of moisture and is
IP44 rated
This product is suitable for use zones 2 and outside zones in a bathroom only.
Please see diagram.
If this unit is being fitted in a room containing a bath or shower, a 30mA RCD
must be used – in accordance with IEE regulations.
Installation
Existing fittings must be completely removed before installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
Note that the power needs to be isolated/switched off at the fuse board.
Ensure that the screws and cable entry points are sealed to maintain the IP
rating of the product.
- Detach the fixing bracket from the product by removing the side fixing screws.
- Using the fixing bracket as template, mark the position of the mounting holes. Drill holes and fit supplied wall plugs (suitable for masonry only – for other surfaces use appropriate fixings). Attach fixing bracket to ceiling.
- Wire product as detailed wiring diagram.
- Refit the shade to the product with the screws set aside earlier.
- Replace fuse or circuit breaker and switch on. Your light is now ready for use.
Wiring
Having correctly identified the wiring from your existing light fitting, Pull the mains wire through the hole and connect to the connection block inside in the following way:
Check that…
- You have correctly identified the wires.
- The connections are tight.
- No loose strands have been left out of the connection block.
- When completed, ensure that there are no bare or loose strands of wire exposed, and cover all exposed areas of the connection block with 2 layers of insulation tape.
Technical data
| Supply Voltage: | 220-240 V~, 50 Hz |
|---|---|
| Bulb Type: | 22W LED module (SMD), 4000K |
This product contains a light source of energy efficiency class E.
| Replaceable (LED only) light source by a professional
---|---
| Replaceable control gear by a professional
| Conformity with all relevant UKCA Directive requirements.
---|---
| Conformity with all relevant EC Directive requirements.
| This product is Class 1, must be connected to earth.
| Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
local store for recycling advice.
| This product is not suitable for dimming.
| This product is rated at IP44.
Care and Safety
Live Voltages may be present in this unit even when turned off or when
completely disconnected.
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish.
For your safety, always switch off the power supply before changing
lightbulbs, or cleaning.
This bulb is protected by a shade. This part must be replaced immediately
should the shade become cracked or damaged. This fitting must not be used
without the shade in place.
For further information, please visit https://www.lighting-info.co.uk/54479
V3 23/06/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>