HUANANZHI X99-8D3 Motherboard User Manual

HUANANZHI X99-8D3 Motherboard

Product Information:

Product Name: X99-8D3
Manufacturer: SZ HUANAN SANXIAN TECHNOLOGY CO.,LTD.
Website: www.huananzhi.com

Product Usage Instructions

Installation and Settings:

1. Ensure all parts are firmly connected during the computer assembly.
2. If components are not recognized or the computer fails to start, check the connections.
3. To prevent ESD damage, discharge your body static by touching other metal objects before removing the motherboard from the box.

Drivers Installation:

Follow the instructions below to install the necessary drivers:

• X-D Chipset Driver: Install the Intel chipset driver for Windows operating systems.
• X-D Sound Card Driver: Install the Realtek sound card driver for Windows operating systems.
• X-D LAN Driver: Install the LAN driver for Windows operating systems.

BIOS Settings:

Access the BIOS settings by following the steps below:

1. Power on the computer and press the Delete key to enter the BIOS.
2. Navigate through the different sections to configure the desired settings.
3. Save the changes and exit the BIOS.

Safety Precautions:

Please follow these safety precautions to prevent damage to the product:

• Avoid electrostatic discharge (ESD) by discharging your body static before handling the motherboard.
• Ensure all parts are firmly connected to prevent component recognition failure or startup issues.
• Check the packaging for any damage or missing accessories upon purchase.
• Contact the manufacturer if there are any issues with the packaging or accessories.

SAFETY PRECAUTIONS

• Products could probably be damaged due to electrostatic discharge(ESD). Please follow these steps below for a successful computer assembly.
• Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.
• In order to prevent products from being damaged by ESD, please make sure to discharge your body static by touching other metal objects before taking the motherboard out of box.
• Hold the border of motherboard when taking it out. Do not touch the sensitive parts of motherboard.
• Please put the motherboard in an anti-static container or on anti-static pad if not needed.
• Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.
• Do not start the computer before installation finished, otherwise it might result in permanent damage to the computer parts or even injury to the user.
• If you need any assistance in the process of installationplease contact our after-sales customer service or reach us on HUANANZHI official E-mail:business@huananzhi.com for professional technical support.
• Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.
• Keep the motherboard away from moisture.
• Keep the user manual for future reference.
• Before plugging the power supply, please make sure the socket provides the corresponding voltage.
• In any of the following situations, please keep the motherboard and power cable in a safe place. Do not put anything onto the power cable.
• In the event of any of the following conditions, have the board checked by a service technician: Liquid penetrated into the computer. Motherboard is exposed to moisture. Motherboard does not work even if you follow the instructions on user manual. Motherboard fell off to the ground and got damaged. Motherboard has clear signs of damage.

PACKING

Please confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to packaging or lack of accessories, contact us as soon as possible.

1. HUANANZHI X-D DUAL Motherboard
2. SATA data cable
3. I/O shield back plat .
4. Warranty Card

BRIEF INTRODUCTION

Features

• CPU: Support LGA2011-3 Processor(Xeon™ E5 2629 v3/ E5-2649 v3/E5-2669 v3/E5-2673 V3/E5-2676 v3/E5-2678 V3/E5-2696 V3/E5-2666 V3/E5-2686v4/E5-2696V4)

• RAM: 8* DIMM supports up to 256GB DDR3 1866/1600/1333MHZ Non-ECC.ECC memory Ouad-Channel Memorv Architecture
  Actual memory data rate depends on CPU type and DRAM module

• 1/O effects: 6 × SATA3.0 (maximum transfer speed up to 6GB/s)
  4 x USB2.0 interface
  4 x USB3.0 ports
  1 x RJ45 Network card interface

• Audio: Realtek Audio Transcoder
  Realtek 5.1 Channel High Fidelity Audio
  Audio output:Front Out/Front Speaker Out
  Audio input:Microphone input, Audio input

• Ethernet: 1 x Realtek PCle Gigabit LAN

• Expansion slot: 2 x PCle 3.0 x16
  1 x PCle 3.0 x4
  2 x M.2 NVME PCIE X4 3.0 32Gb/s(2242/2260/2280)

MOTHERBOARD DIAGRAM

X99-8D3 DUAL Motherboard

Rear I/O Panel

LAN Port Status Table

Installation And Settings

NOTICE
please check the motherboard where all pins marked with number “1” or white bold line are position “1′

In order to properly place the CPU in the motherboard, the surface of the LGA 2011-3 CPU has two pairs of starting points and a golden triangle. Golden triangle indicates Pin1

M.2 Interface Installation

1. Remove the screw from the screw base
2. Remove the screw base
3. Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole
4. Insert your M.2 module into the M.2 interface at a 30 degree angle
5. Place the screw on the trailing edge notch of your M.2 module and tighten to the screw base

Memory Installation

1. Pull the clips on both ends of the memory slot outward, and the memory strip corresponds to the protruding position of the slot to determine the direction of installation.
2. Align the memory module into the slot and press
3. Let the snaps on both ends of the slot automatically bounce

Graphics Card Installation

1. Use a screwdriver to remove the bezel and screws on the main unit
2. Need to pick up the card slot of the card slot when installing the graphics card
3. Insert the graphics card into the card slot of the graphics card
4. After the installation is in place, the chuck will automati- cally return to its position.
5. Secure the graphics card to the chassis with screws
6. Install the power cord

SATA Interface

Drivers installation

1. Drivers listing:

2. Intel Chip Information Installation Run “Control Panel – System – Hardware – Device Manager” Click the right mouse button to change the driver’s hardware device and proceed with the installation below:
   Option: Propertyl – Update driverl – Not connect to Internet –
   Manually installation
   Find the corresponding directory
   Select “Next step”

3. Audio driver installation
   Before this installation, please check the model of the audio chip on the motherboard first(you may refer to this manual), Select the proper driver accordingly for installation.

4. Audio driver installation (take HD Audio series for example)
   Run “driver installer”: X99-8D3 Audio.rar/9239_FF00_PG478_Win 10_RS4_RS5_19H1_20H1_Win7_WHQL/Setup.exe
   Click on the file “WDW-267”
   Click on “next”to continue,and then”finished”
   The system will automatically restart itself to finish the installation

5. Uninstallation of audio driver(take HD Audio series for example)
   Boot to the Windows desktop, choose “setting” / “control”, and then “add/remove programs”. Later,choose “Realtek High Definition Audio Driver” in the menu and click on “add/remove”so that the driver will be automatically removed.

6. Driver installation of external video card Run “driver installer”, take Setup.exe,Click on “next” – “yes” -“next” “next” and “finished”h
   The system will automatically search for devices to complete the installation

7. Driver installation of network
   Run “driver installer”: X99-8D3 LAN/setup.exe click on “next”-“installation”- “finished” and restart the computer,and restart the computer, The system will automatically search for devices to complete the installation.

BIOS Settings

In order to enable the computer to work well or execute specific functions, CMOS SETUP normally stores all kinds of data in CMOS SRAM of the motherboard. When the computer is shut down, motherboard’ s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST (Power On Self Test), press “Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. Motherboard warm boot key is “F7”.

Menu: please pay attention to every option in the settings menu. When there is a triangle shaped symbol on the left side of menu, it means that you choose this sub-menu,so a pop-up sub-menu will be available.

Main Menu Function

• Main
• System Overview
• Date/Time settings, HDD specs/Monitor type settings.
• Advanced
• Advanced Settings
• BIOS special function settings, such as virus alert, booting disk priority etc.
• Chipest
• Advanced Chipest Settings
• Boot
• Boot Settings
• Security
• Security Settings
• Save
• Save Setting
• Exit
• Exit Options

Exit settings include loading of optimized defaults value/ loading of fail- safe defaults / discarding changes/ exiting without saving.Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding chang-es/ exiting without saving.

SZ HUANAN SANXIAN TECHNOLOGY CO.,LTD.
WWW.HUANANZHI.COM

References

• 华南金牌官网

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>