HUANANZHI X79 Dual-4D Motherboard User Manual

HUANANZHI X79 Dual-4D Motherboard

Product Information

The X79 DUAL-4D motherboard is manufactured by SZ HUANAN SANXIAN TECHNOLOGY CO.,LTD. It supports Intel CPUs with LGA2011 socket and has four DDR3 DIMM slots with support for ECC memory. The motherboard has multiple expansion slots including two PCIe 3.0 x16, two PCIe 3.0 x8, one PCIe 2.0 x16, and one PCIe 2.0 x1. It also has two M.2 slots (one for NVME PCIe and one for key M) and eight SATA ports (four of which support speeds up to 6Gb/s). The motherboard supports USB 3.0 and has a Realtek LAN controller with speeds up to 1000Mbps.

Product Usage Instructions

Before assembling the computer, follow these safety precautions to prevent damage from electrostatic discharge (ESD):

1. Make sure all parts are firmly connected.
2. Discharge your body static by touching other metal objects before taking the motherboard out of the box.

If the product packaging is damaged or there are missing accessories, contact the manufacturer immediately. The package should include:

• HUANANZHI X-D DUAL LU Motherboard
• SATA data cable
• I/O shield back plate
• User manual
• Warranty card

For installation and settings, refer to the user manual. The manual includes instructions for:

• Drivers installation
• BIOS settings

SAFETY PRECAUTIONS

• Products could probably be damaged due to electrostatic discharge(ESD). Please follow these steps below for a success-ful computer assembly.

• Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.

• In order to prevent products from being damaged by ESD, please make sure to discharge your body static by touching other metal objects before taking the motherboard out of box.

• Hold the border of motherboard when taking it out. Do not touch the sensitive parts of motherboard.

• Please put the motherboard in an anti-static container or on anti-static pad if not needed.

• Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.

• Do not start the computer before installation finished, otherwise it might result in permanent damage to the computer parts or even injury to the user.

• If you need any assistance in the process of installation， please contact our after-sales customer service or reach us on HUANANZHI
  official E-mail:business@huananzhi.com for professional technical support.

• Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.

• Keep the motherboard away from moisture.

• Keep the user manual for future reference.

• Before plugging the power supply, please make sure the socket provides the corresponding voltage.

• In any of the following situations, please keep the motherboard and power cable in a safe place. Do not put anything onto the power cable.

• In the event of any of the following conditions, have the board checked by a service technician:

  • Liquid penetrated into the computer.
  • Motherboard is exposed to moisture.
  • Motherboard does not work even if you follow the instructions on user manual.
  • Motherboard fell off to the ground and got damaged.
  • Motherboard has clear signs of damage.

PACKING

• Please confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to packaging or lack of accessories, contact us as soon as possible.
• 1.1 HUANANZHI X-D DUAL LU Motherboard
• 2.2 SATA data cable
• 3.1 I/O shield back plat
• 4.1 User Manual
• 5.1 Warranty Card

BRIEF INTRODUCTION

Features

• CPU: Intel ® LGA2011 Processor Intel ® Xeon™
• RAM: 4* DIMM supports up to 128GB DDR3
• 1866/1600/1333MHZ Non-ECC.ECC memory
• Two-Channel Memory Architecture
• Actual memory data rate depends on CPU type and DRAM module
• 1/O effects: 2 x SATA3.0 (maximum transfer speed up to 6GB/s)
• 4 x SATA2.0 (maximum transfer speed up to 2GB/s)
• 6 x USB2.0 interface
• 2 x USB3.0 ports
• 1 x PS/2 Mouse and Keyboard port
• 2 x RJ45 Network card interface
• Audio: Realtek Audio Transcoder
• Realtek 5.1 Channel High Fidelity Audio
• Audio output: Front Out/Front Speaker Out
• Audio input: Microphone input, Audio input
• Ethernet: 2 x Realtek PCle Gigabit LAN
• Expansion slot: 2 x PCle 3.0 x16
• 2 x PCle x1
• 1 x M.2 NVME PCIe 3.0X4 (key M)2242/2260/2280

MOTHERBOARD DIAGRAM

X79-4D DUAL LU Motherboard

Rear I/O Panel

Overall Rear I/O Panel Display

LAN Port Status Table
Audio Port Configuration

Installation And Settings

NOTICE
please check the motherboard where all pins marked with number “1” or white bold line are position “1”

Clear CMOS Jumper CLR-CMOS

1| MIC+| 2| Ground
3| Vbias| 4| AuD_ Vcc(AVCC)
5| ROut| 6| R Out Back
7| N.C| 8| KEY
9| L_Out| 10| L_Out Back

Front Audio Output Ports

1| VCC| 2| VCC
3| D-| 4| D-
5| D+| 6| D+
7| GND| 8| GND
9| KEY| 10| N.C

USB Extension Interface PCI Expansion Slot

1| PWR LED+| 2| HDD LED+
3| PWR LED-| 4| HDD LED-
5| PWR_SW| 6| RESET_SW
7| PWR_SW| 8| RESET_SW
9| KEY| 10| N.C

F_PANEL1 Boot Interface

1| Power| 2| USB3_RX_DN
3| USB3_RX_DP| 4| Ground
5| USB3_TX_C_DN| 6| USB3_TX_C_DP
7| Ground| 8| USB2.0-
9| USB2.0+| 10| GND
11| USB2.0+| 12| USB2.0-
13| Ground| 14| USB3_TX_C_DP
15| USB3_TX_C_DN| 16| Ground
17| USB3_RX_DP| 18| USB3_RX_DN
19| Power| 20| N.C

USB3.0 Interface

• In order to properly place the CPU in the motherboard, the surface of the LGA 2011 CPU has two pairs of start-ing points and a golden triangle. Golden triangle indicates Pin1

CPU Installation

1. Remove the screw from the screw base

2. Remove the screw base

3. Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole

4. Insert your M.2 module into the M.2interface at a 30 degree angle

5. Place the screw on the trailing edge notch of your M.2 module and tighten to the screw base

M.2 Interface Installation

1. Pull the clips on both ends of the memory slot outward, and the memory strip corresponds to the protruding position of the slot to determine the direction of installation.
2. Align the memory module into the slot and press
3. Let the snaps on both ends of the slot automatically bounce

Memory Installation

1. Use a screwdriver to remove the bezel and screws on the main unit

2. Need to pick up the card slot of the card slot when installing the graphics card

3. Insert the graphics card into the card slot of the graphics card
   

4. After the installation is in place, the chuck will automati-cally return to its position.

5. Secure the graphics card to the chassis with screws

6. Install the power cord

Graphics Card Installation

SATA Interface

Drivers installation

Drivers listing:

win7/win10
X79-4D LAN Driver| Intel chip NIC installation| win7/win10

Intel Chip Information Installation
Run “Control Panel – System – Hardware – Device Manager” Click the right mouse button to change the driver’s hardware device and proceed with the installation below：
Option: Propertyl – Update driverl – Not connect to Internet – Manually installation
Find the corresponding directory
Select “Next step”

Audio driver installation
Before this installation, please check the model of the audio chip on the motherboard first(you may refer to this manual), Select the proper driver accordingly for installation.

• Audio driver installation (take HD Audio series for example)
  Run “driver installer”: /X79-4D SOUND CARD DRIVER/VISTA-WIN7-R267, take WDW-267 if OS is XP Click on “next” to continue, and then” finished” The system will automatically restart itself to finish the installation

•  Uninstallation of audio driver(take HD Audio series for example)
  Setting into Windows desktop, choose “setting”/ “control”, and then “add/remove programs”. Later, choose “Realtek High Definition Audio Driver” in the menu and click on ” add/remove” so that the driver will be automatically removed.。

Driver installation of external video card

Run “driver installer”, take Setup.exe,
Click on “next”- “yes”
-“next”
-“next”and”finished”h
The system will automatically search for devices to complete the installation

Driver installation of network

Run “driver installer”: X-D LAN DRIVER/WIN XP click on “next”-
“installation”- “finished”and restart the computer， and restart the computer，The system will automatically search for devices to complete the installation.

BIOS Settings

In order to enable the computer to work well or execute specific functions, CMOS SETUP normally stores all kinds of data in CMOS SRAM of the motherboard. When the computer is shut down, motherboard’s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST(Power On Self Test), press “Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. Motherboard warm boot key is “F”.
Menu: please pay attention to every option in the settings menu. When there is a triangle shaped symbol on the left side of menu, it means that you choose this sub-menu,so a pop-up sub-menu will be available.
Main Menu Function

• Main
• System Overview
• Date/Time settings, HDD specs/Monitor type settings.
• Advanced
• Advanced Settings
• BIOS special function settings, such as virus alert, booting disk priority etc.
• Chipest
• Advanced Chipest Settings
• Boot
• Boot Settings
• Security
• Security Settings
• Save
• Save Setting
• Exit
• Exit Options

Exit settings include loading of optimized defaults value/ loading of fail- safe defaults / discarding changes/ exiting without saving.Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding chang-es/ exiting without saving.

References

• 华南金牌官网

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>