HUANANZHI X99-F8D Motherboard User Manual

HUANANZHI X99-F8D Motherboard

Product Information

The product is a motherboard manufactured by SZ HUANAN SANXIAN TECHNOLOGY CO.,LTD. It supports DDR RAM with a maximum capacity of GB and a frequency of //MHZ ECC.ECC. The motherboard has various I/O ports including SATA, SSATA, USB, and RJ45. It also has Realtek audio and LAN controllers. The motherboard supports PCIe, M. NVME PCIe, and M. NGFF(SATA.) expansion cards. It has a CPU socket for LGA-CPU with pins. The motherboard comes with chipset drivers and Realtek sound card driver on X-FD.

Product Usage Instructions

Before starting the installation process, ensure that you follow the safety precautions mentioned in the user manual. To prevent electrostatic discharge (ESD) damage, discharge your body static by touching other metal objects before taking the motherboard out of the box. Switch off the power and disconnect the power cable from the  socket before starting the installation or disassembly process. Refer to the motherboard diagram and rear I/O panel for proper installation and connection of components. Make sure all parts are firmly connected to avoid recognition failure or startup issues. For expansion cards, the motherboard supports PCIe, M. NVME PCIe, and M. NGFF(SATA.) types. Install the cards properly in their respective slots. Download and install the chipset drivers, Realtek sound card driver, and LAN driver from the X-FD before starting to use the motherboard. Refer to the BIOS settings section of the user manual for configuring BIOS settings.

SAFETY PRECAUTIONS

• Products could probably be damaged due to electrostatic discharge(ESD). Please follow these steps below for a success-ful computer assembly.

• Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.

• In order to prevent products from being damaged by ESD, please make sure to discharge your body static by touching other metal objects before taking the motherboard out of box.

• Hold the border of motherboard when taking it out. Do not touch the sensitive parts of motherboard.

• Please put the motherboard in an anti-static container or on anti-static pad if not needed.

• Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.

• Do not start the computer before installation finished, otherwise it might result in permanent damage to the computer parts or even injury to the user.

• If you need any assistance in the process of installation，please contact our after-sales customer service or reach us on HUANANZHI official
  E-mail:business@huananzhi.com for professional technical support.

• Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.

• Keep the motherboard away from moisture.

• Keep the user manual for future reference.

• Before plugging the power supply, please make sure the socket provides the corresponding voltage.

• In any of the following situations, please keep the motherboard and power cable in a safe place. Do not put anything onto the power cable.

• In the event of any of the following conditions, have the board checked by a service technician:

  • Liquid penetrated into the computer.
  • Motherboard is exposed to moisture.
  • Motherboard does not work even if you follow the instructions on user manual.
  • Motherboard fell off to the ground and got damaged.
  • Motherboard has clear signs of damage.

PACKING

• Please confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to packaging or lack of accessories, contact us as soon as possible.
• 1.1 HUANANZHI X99-F8D DUAL motherboard
• 2.2  SATA data cable
• 3.1 I/O shield back plat
• 4.1  User Manual
• 5.1 Warranty Card

BRIEF INTRODUCTION

Features

CPU: Intel® LGA2011-3 Processor Intel® Xeon™
Intel® LGA2011-3 5th/6th Generation Intel® Core™
RAM: 8* DIMM supports up to 256GB DDR4
2400/2133/1866MHZ Non-ECC.ECC memory
Quad-Channel Memory Architecture
Actual memory data rate depends on CPU type and DRAM module
1/O effects: 6 x SATA 3.0 (maximum transfer speed up to 6GB/s)
4 x SSATA3.0
4 x USB2.0 interface
4 x USB3.0 ports
1 x RJ45 Network card interface
Audio: Realtek Audio Transcoder
Realtek 7.1 Surround Sound High Definition Audio Codec
Audio output: Front Out/Front Speaker Out, Rear Speaker output, Center/Subwoofer output, Optical audio output
Audio input: Microphone input, Audio input
Ethernet: 1 x Realtek PCle Gigabit LAN
Expansion slot: 3 x PCle 3.0 x16
1 x M.2 NVME PCle 3.0X4 (key M) 2242/2260/2280
1 x M.2 NVME PCle 3.0 X4(key M)/M.2 NGFF(SATA 3.0)
2242/2260/2280

MOTHERBOARD DIAGRAM

X99-F8D motherboard illustration

Rear I/O Panel

Overall Rear I/O Panel Display
LAN Port Status Table
Audio Port Configuration

Installation And Settings

NOTICE
please check the motherboard where all pins marked with number “‘” or white bold line are position

Clear CMOS Jumper CLR-CMOS

Front Audio Output Ports

USB Extension Interface
PCI Expansion Slot

F_PANEL1 Boot Interface

USB3.0 Interface

• In order to properly place the CPU in the motherboard, the surface of the LGA2011-3 CPU has two pairs of starting points and a golden
  triangle. Golden triangle indicates Pin1
  

CPU Installation

1. Remove the screw from the screw base

2. Remove the screw base
   

3. Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole

4. Insert your M.2 module into the M.2 interface at a 30 degree angle

5. Place the screw on the trailing edge notch of your M.2 module and tighten to the screw base

M.2 Interface Installation

1. Pull the clips on both ends of the memory slot outward, and the memory strip corresponds to the protruding position of the slot to determine the direction of installation.
2. Align the memory module into the slot and press
3. Let the snaps on both ends of the slot automatically bounce

Memory Installation

1. Use a screwdriver to remove the bezel and screws on the main unit

2. Need to pick up the card slot of the card slot when installing the graphics card

3. Insert the graphics card into the card slot of the graphics card
   

4. After the installation is in place, the chuck will automatically return to its position.

5. Secure the graphics card to the chassis with screws

6. Install the power cord

Graphics Card Installation

SATA Interface

Drivers installation

Drivers listing: Intel Chip Information Installation
Run “Control Panel – System – Hardware – Device Manager” Click the right mouse button to change the driver’s hardware device and proceed with the installation below：
Option: Propertyl – Update driverl – Not connect to Internet – Manually installation
Find the corresponding directory
Select “Next step”

Audio driver installation
Before this installation, please check the model of the audio chip on the motherboard first(you may refer to this manual), Select the proper driver accordingly for installation.

• Audio driver installation (take HD Audio series for example)
  Run “driver installer: /X99-F8DAudio/ALC662-32bit_Win?_Win8_Win81 Win10 R279/ALC662-64bit Win7 Win8 Win81 Win10 R279.exeClick on “next” to continue, and then “finishedThe system will automatically restart itself to finish the installation

•  Uninstallation of audio driver(take HD Audio series for example)
  Setting into Windows desktop, choose “setting”/ “control”, and then “add/remove programs”. Later, choose “Realtek High Definition Audio Driver” in the menu and click on “add/remove” so that the driver will be automatically removed.

Driver installation of external video card
Run “driver installer”, take Setup.exe, Click on “next”- “yes”
-“next”
-“next” and” finished “h
The system will automatically search for devices to complete the installation

Driver installation of network
Run “driver installer”: X99-F8DLAN/setup.exe
click on “next”-
“installation”- “finished” and restart the computer， and restart the computer， The system will automatically search for devices to complete the installation.

BIOS Settings

In order to enable the computer to work well or execute specific functions, CMOS SETUP normally stores all kinds of data in CMOS SRAM of the motherboard. When the computer is shut down, motherboard’s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST(Power On Self Test), press “Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. Motherboard warm boot key is “F7”.
Menu: please pay attention to every option in the settings menu. When there is a triangle shaped symbol on the left side of menu, it means that you choose this sub-menu, so a pop-up sub-menu will be available.

Main Menu Function

• Main

• System Overview
  Date/Time settings, HDD specs/Monitor type settings.

• Advanced
  Advanced Settings
  BIOS special function settings, such as virus alert, booting disk priority etc.

• Chipest
  Advanced Chipest Settings

• Boot
  Boot Settings

• Security
  Security Settings

• Save
  Save Setting

• Exit
  Exit Options
  Exit settings include loading of optimized defaults value/ loading of fail- safe defaults / discarding changes/ exiting without saving. Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.

References

• 华南金牌官网

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>