HUANANZHI B75 M.2 Motherboard User Manual

HUANANZHI B75 M.2 Motherboard

Product Information

• Brand: HUANANZHI
• Model: B Motherboard
• Memory: RAM*DIMM supports up to GB DDR /MHZ Non-ECC memory with Two-Channel Memory Architecture. The actual memory data rate depends on CPU type and DRAM module.
• I/O: 2 x SATA (maximum transfer speed up to GB/s), 2 x SATA (maximum transfer speed up to GB/s), 4 x USB interface, 2 x USB ports, 1 x PS/ Mouse and Keyboard port, 1 x RJ Network card interface, 1 x VGA, 1 x HDMI-Compatible, and 1 x DVI-I
• Chipset: Intel B Chipset Driver
• Audio: Realtek High Definition Audio Driver
• LAN: Intel LAN Driver
• BIOS: BIOSPOST (Power On Self Test) with AMI BIOS and CMOS SRAM. CMOS SETUP F is available.

Product Usage Instructions

Safety Precautions:

• Products could probably be damaged due to electrostatic discharge (ESD). To prevent this, discharge your body static by touching other metal objects before taking the motherboard out of the box.
• Make sure all parts are firmly connected to avoid failure of recognizing components or starting the computer.
• Confirm that the motherboard is properly packaged upon purchase of the product. Contact the seller if there is any damage to packaging or lack of accessories.

Installation:

• Refer to the motherboard diagram and rear I/O panel for installation and connection of components.
• Connect the SATA data cables, USB interfaces, PS/ Keyboard and
  Mouse port, RJ Network card interface, VGA, HDMI-Compatible, and DVI-I according to the I/O effects.

Drivers Installation:

• Install the Intel B Chipset Driver, Realtek High Definition Audio Driver, and Intel LAN Driver for proper functioning of the motherboard.
• Install DirectX tools for better graphics performance.

BIOS Settings:

• Access the BIOS by pressing Delete during BIOSPOST (Power On Self Test).
• Refer to the BIOS directory for Main, Advanced, Chipset, Boot, Security, Save, and Exit settings.

SAFETY PRECAUTIONS

• Products could probably be damaged due to electrostatic discharge(ESD). Please follow these steps below for a success-ful computer assembly.
• Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.
• In order to prevent products from being damaged by ESD, please make sure to discharge your body static by touching other metal objects before taking the motherboard out of box.
• Hold the border of motherboard when taking it out. Do not touch the sensitive parts of motherboard.
• Please put the motherboard in an anti-static container or on anti-static pad if not needed.
• Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.
• Do not start the computer before installation finished, otherwise it might result in permanent damage to the computer parts or even injury to the user.
• If you need any assistance in the process of installation，please contact our after-sales customer service or reach us on HUANANZHI official E-mail: business@huananzhi.com for professional technical support.
• Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.
• Keep the motherboard away from moisture.
• Keep the user manual for future reference.
• Before plugging the power supply, please make sure the socket provides the corresponding voltage.
• In any of the following situations, please keep the motherboard and power cable in a safe place. Do not put anything onto the power cable.
• In the event of any of the following conditions, have the board checked by a service technician:
• Liquid penetrated the computer.
• The motherboard is exposed to moisture.
• Motherboard does not work even if you follow the instructions on user manual.
• Motherboard fell off to the ground and got damaged. Motherboard has clear signs of damage.

PACKING

• Please confirm that the motherboard is properly packaged upon purchase of the product.
• If there is any damage to packaging or lack of accessories, contact us as soon as possible.
• HUANANZHI B motherboard
• ATA data cable
• User manual
• Warranty card

BRIEF INTRODUCTION

Features

• CPU: Intel © LGA 1155 13/15/17 2th 3th Intel ® Core ™
  • Intel LGA1155 processor 2th 3th Intel ® Celeron I
  • Intel LGA1155 Processor 2th 3th Intel ® Pentium ™
  • Intel LGA1155 Processor E3 V2 Series Intel ® Xeon™
• RAM: 2’DIMM supports up to 16GB DDR3
  • 1600/1333MHZ Non-ECC memory
  • Two-Channel Memory Architecture
  • Actual memory data rate depends on CPU type and DRAM module
• 1/O effects: 1 x SATA3.0 (maximum transfer speed up to 6GB/s)
  • 3 x SATA2.0 (maximum transfer speed up to 2GB/s)
  • 4 x USB2.0 interface
  • 2 x USB3.0 ports
  • 1 x PS/2 Mouse and Keyboard port
  • 1 x RJ45 Network card interface
  • 1 x VGA
  • 1 x HDMI-Compatible
  • 1 x DVI-
• Audio: Realtek Audio Transcoder
• Realtek 5.1 Channel High-Fidelity Audio
• Audio output: Front Out/Front Speaker Out
• Audio input: Microphone input, Audio input
• Ethernet: 1 × Realtek PCle 1000MB LAN
• Expansion slot: 1 x PCle 3.0 x16
  • 1 x PCle 2.0 x1
  • 1 x PCle x1

THE MOTHERBOARD DIAGRAM

Rear I/O Panel

1-3 LAN Port Status Table

Installation And Settings

NOTICE

please check the motherboard where all pins marked with number or white bold line are position

• To place the CPU properly on the motherboard, the SURFACE of the
• LGA1155 CPU has two pairs of starting points and a golden trian- gle. The golden triangle indicates Pin1

1. Pull the clips at both ends of the memory slot outwards, and the memory strip corresponds to the protruding position of the slot to determine the direction of installa- tion
2. Align the memory strip to the slot and press down
3. Make the clips on both ends of the slot spring up automatically

2-7 Memory Installation

1. Use a screwdriver to remove the bezel and screws on the main unit
2. Need to pick up the card slot of the card slot when installing the graphics card
3. Insert the graphics card into the card slot of the graphics card
4. After the installation is in place, the chuck will automatically return to its position.
5. Secure the graphics card to the chassis with screws
6. Install the power cord

2-8 Graphics Card Installation

Drivers Installation

Intel Chip Information Installation

• Run “Control Panel – System – Hardware – Device Manager” Click the right mouse button to change the driver’s hardware device and proceed with the installation below:
• Option: Propertyl – Update driverl – Not connect to Internet –
• Manually installation
• Find the corresponding directory
• Select “Next step”

Directx11 driver installation

• Run “driver installer” :/ Tools/ Direct×11/ DXSETUP
• Click “Setup.exe” file to continue
• Select “Next” to continue
• Select “Finish” and restart the computer. The system wil automatically find the devices. Installation finished.

Audio driver installation

• Before this installation, please check the model of the audio chip on the motherboard first(you may refer to this manual), Select the proper driver accordingly for installation.

Audio driver installation (take HD Audio series for example)

• Run “driver installer”: /B75 SOUND CARD DRIVER/VISTA-WIN7-R267, take WDW-267 if OS is XP
• Click on “next”to continue, and then”finished”
• The system will automatically restart itself to finish the installation

Driver installation of external video card

• Getting into Windows desktop, choose “setting”/ “control”, and then “add/remove programs”. Later, choose “Realtek High Definition Audio Driver” in the menu and click on add/remove”so that the driver will be automatically removed.

Driver installation of external video card

• Run “driver installer”, take Setup.exe,
• click on “next”-“yes”
• next”
• next”and”finished”
• The system will automatically search for devices to complete the installation

Driver installation of network

• Run “driver installer”: B75 LAN DRIVER/WIN7 XP click on next”-“installation”-“finished” and restart the computer, the system will automatically search for devices to complete the installation.

BIOS Settings

• In order to enable the computer to work well or execute specific
• functions, CMOS SETUP normally stores all kinds of data in CMOS SRAM of the motherboard. When the computer is shut down, motherboard’s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST(Power On Self Test), press “Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. Motherboard warm boot key is “FT”
• Menu: please pay attention to every option in the settings menu.
• When there is a triangle shaped symbol on the left side of menu, it means that you choose this sub-menu,so a pop-up sub-menu will be available.

Main Menu Function

• Main
• System Overview
• Date/Time settings, HDD specs/Monitor type settings.
• Advanced
• Advanced Settings
• Chipest
• Advanced Chipest Settings
• BIOS special function settings, such as virus alert, booting disk priority etc.
• Boot
• Boot Settings
• Security
• Security Settings
• Save
• Save Setting
• Exit
• Exit Options
• Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>