saxby lighting 101336 DualLED 4ft 20W/38W Tri Colour Batten Instruction Manual
- June 12, 2024
- saxby lighting
Table of Contents
Instruction Manual
DualLED
**101336 , 101338
**
Than you for purchasing this light fitting.
Please lead the instructions carefully before use to ensure sale and
satisfactory operation of this product. Please retain these instructions for
future reference.
Warning
This is a Class 1 product and must be earthed. Please read these instructions
carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Check the pack and make sure you have all the parts listed. Install in
accordance with Me IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch oil at mains supply before installing or
maintaining this fitting. Ensure other persons camel restore the electrical
supply without your knowledge.
II you are in any doubt, please consult a qualified electrician.
This light lilting should be connected to a fused circuit. It replacing an
existing fitting, make a careful note of the connections. This product
contains non-replaceable parts and cannot be serviced.
II damage occurs the part should be scrapped. Waste electrical products should
not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Layout
Plan the desired layout of these finings carefully. ensuring the cables will reach the distances between the junction box and the each light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boas (not supplied) may from areas where they may be at risk from being cut. trapped or damaged. The mains supply cable must have a minimum cross section area of Cables must be protected using suitable conduit or plastic bunking. Take care not to drill into any pipes cc mains cables beneath the surface during mowiting holes preparation. This product can be installed on the ceiling or wall.
Installation
Existing linings must be completely removed before installation of a new
product. Before removing the existing fitting, carefulty note the position of
each set of wires.
Note that the switch is turned off belore installation. The mounting surlace
must be flat and smooth to ensue a good fit.
- Undo two screws at the end of the product to separate the diffuser cover from the rear panel, the diffuser has a lip so working from one end compress the diffuser to release the lip. Put the diffuser and screws in sate place for refitting later.
- This unit can be mounted on the wall or ceiling. Alter deciding the mounted way accordingly, Using the rear panel as a template mark the position to drill out the fixing holes. Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used, depending upon the surface to be mounted.
- This product is colur changing and can be either warm while (3000K) or cool white (4000K) or daylight white (6000K). And can be changed the wattage 38W/20W for 101336. can be changed the wattage 581N/30W for 101338. Choose your preferred colour / wattage before installing by sliding the CCT switch /Wave switch inside the product. Note: Befeore you change the colour and wattage, please tum off the power switch for safety.
- Choose the cable entry holes on the rear panel and dell out the conduit knockouts accordingly it necessary. Then pull the cable through the cable entry hole
- Fix the rear panel into the position with the installation plugs and screws (supplied).
- Connect the supply cable to the quick lit terminal block as detailed wiring diagram.
- Reid the diffuser cover by clipping back into place (you may find il easier to insert one side first like a hinge then clip the remaining side into place) Ensuring you secure by tightening the screws each end
- Replace fuse or circuit breaker and switch on. Your light is now ready for use.
Wiring
This product is Class I product must be earthed. They must be joined together
and well insulated with good quality insulation tape. This is to ensure earth
continuity throughout you property. Having correctly identified the wiring
from you existing light fitting and connect to the quick lit connection block
inside the product in the following way
Technical data
Supply 220-240 V—, 50 Hz
Voltage: Bulb 101336: 38/20W LED module (SMD), CCT 3000/4000/6000K
Type: 101338 : 58/30W LED module (SMD), CCT 3000/4000/6000K
This product contains a light source of energy efficiency class D.
| Non-replaceable light source
---|---
| Replaceable control gear by a professional
| Conformity with all relevant UKCA Directive requirements.
| Conformity with all relevant EC Directive requirements.
****| This product is Class 1, must be connected to earth.
| Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
local store for recycling advice.
| This product is not suitable for dimming.
Care and Safety
Live Voltages may be present in this unit even when turned off or when completely disconnected. We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch oft the power supply before cleaning.
For further information, please visit https://Avww.lighting-
info.co.uk/101336
V1 17/08/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Briliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>