saxby lighting 13758 Mareh Mirror Instruction Manual

: June 12, 2024
: saxby lighting

Table of Contents

saxby lighting 13758 Mareh Mirror
Installation
Technical Data
Care and Safety
Read User Manual Online (PDF format)
Download This Manual (PDF format)

saxby lighting 13758 Mareh Mirror

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning

This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Check the pack and make sure you have all the parts listed.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
This product is suitable for indoor use only, on normal flammable surfaces.
This product contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distance between the Junction box and the light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross sectional area of 1.Dmm2 Cables in wall must be protected using suitable conduit or plastic trunking.
This product has special protection against the ingress of moisture.
This product is suitable for use bathroom zone 2 and outside zones of a bathroom only. Please see diagram on the right.
If this unit is being fitted in zone 1 a room containing a bath or shower, a 30mA RCD must be used – in accordance with IEE regulations.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
Note that the switch is turned off before installation.
This product is suitable for installation on surfaces with normal flammability e.g. wood, plasterboard and masonry. It is not suitable for use on highly flammable surfaces (e.g. polystyrene, textiles).
If mounting, note the position of the “This Way Up” label on the back of the product and ensure it is correctly oriented.
An assistant may be required to aid installation of this product.
- Remove the wall back from the product by removing the side fixing screws and rubber washers.
- Hold the wall back in place and mark the position of the holes. Ensure that the product is level.
- Ensure the drain hole is at the base of the wall back, and that the product is correct orientated with the pull cord at the bottom. Thread the cable through the grommet.
- Ensure the wall is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
- Pierce grommet and pass the supply cable through the hole in the wall back.
- Fix the product into position. Take care not to trap the supply wire.

Wiring
Having correctly identified the wiring from your light fitting, Pull the wire through the hole and connect to the connection block inside the product in the following way:

saxby-lighting-13758-Mareh-Mirror-FIG-3

Check that…

You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.

Commissioning

Refit the mirror onto the wall back. Ensure that the seals are correctly located before securing.
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Technical Data

Supply Voltage: 220-240 V-, 50 Hz
Bulb Type: 7W LED module (SM□), 6500K This product contains a light source of energy efficiency class E.

Replaceable (LED only) light source by a professional
Replaceable control gear by a professional

Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
This product is Class 1, must be connected to earth.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
This product is not suitable for dimming.
This product is rated at IP44.

Care and Safety

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. Mirror-Use a damp cloth or a propriety glass cleaner. Do not use abrasive materials as these will damage the finish.

Live Voltages may be present in this unit even when turned of or when completely disconnected.
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.

****The mirror must be replaced immediately should it become cracked or damaged. This fitting must not be used without the mirror in place.

For further information, please visit https://www.lighting-info.eo.uk/31469