dewenwils HODT12D Outdoor Remote Control Timer Switch Instruction Manual
- June 12, 2024
- dewenwils
Table of Contents
dewenwils HODT12D Outdoor Remote Control Timer Switch
Product Information
The ZJ ZJ-3A Outdoor Remote Control Timer Switch is a device that allows you to control the power supply to your outdoor devices remotely. It comes with a transmitter and a receiver, which are already paired and ready to use. The transmitter uses 3×1.5V AA batteries, while the receiver is plugged into a powered outlet.
This timer switch has the following features:
- Waterproof design to prevent water immersion
- Maximum ratings for connected devices
- Child safety measures
- Environmentally-friendly disposal of used batteries
- Variable learning codes technology to eliminate interference
- Transmitter timing settings within a range of 100 feet
Product Usage Instructions
Installation
- Plug the receiver into a powered outlet.
- Plug your device into the socket of the receiver.
- Install 3×1.5V AA batteries in the transmitter.
- To test if your device is paired, press the ON/OFF button on the transmitter and check if the receiver turns ON/OFF. Note: If the receiver doesn’t respond, follow the pairing procedure in the Settings of Transmitter and Receiver section.
Settings of Transmitter and Receiver
Pairing Steps:
- Plug the receiver into an outlet.
- Press and hold the programming button on the receiver until the indicator light starts flashing slowly.
- Release the button and press the ON button, followed by the OFF button on your transmitter.
- The indicator light will stop flashing and remain on to indicate successful programming.
- Repeat steps 1-4 to pair multiple transmitters and receivers.
Cancel Pairing Steps:
- To cancel all programming, press and hold the programming button on the receiver until the indicator light starts flashing rapidly.
- Release the programming button and then press it again. The indicator light will turn off, indicating that all programming has been canceled.
Note : The transmitter and receiver have already been paired in advance and can be used directly. Only follow the pairing steps if the receiver doesn’t respond to the transmitter’s ON/OFF button.
Transmitter Timing Settings
Notes : The receiver must be located within 100 feet of the remote transmitter. The actual functional range may be affected by weather, radio frequency interference, low remote battery, and obstructions between the transmitter and receiver.
- Before setting the transmitter, place it indoors at the desired location.
- Press the ON/OFF button on the transmitter to test if it can successfully control the receiver.
Warning: To reduce the risk of fire, electric shock or personal injury, please strictly follow the instructions.
- To prevent water immersion, the outlet must be mounted in a vertical position with the outlets facing downward and at least 2ft above the ground level.
- Do not immerse in water.
- Do not connect any devices which may exceed the maximum ratings of this remote outlet.
- Do not disassemble or repair the product, but only by authorized service personnel.
- Children are not allowed to use the remote outlets without supervision.
- To prevent children’s suffocation and choking, keep them away from packaging materials.
- Used batteries should be disposed of safely and environmentally.
Product Layout
Installation Guiding
- Plug the receiver into a powered outlet, Plug your device into the socket of the receiver.
- Install 3×1.5V AA batteries for the transmitter.
- Test if your device is paired: Check if the receiver will turn ON/OFF by pressing the transmitter’s ON/OFF button.
NOTE : The transmitter and receiver have been paired in advance and can be used directly. If the receiver cannot be turned on/off by pressing the ON/OFF button of the transmitter, you need to pair it according to the “pairing procedure” in “Settings of Transmitter and Receiver”. Settings of Transmitter and Receiver
Pairing Steps
- Plug the receiver into an outlet.
- Press the programming button on the receiver until the indicator light begins to flash slowly.
- Release the button and press the ON button, then the OFF button on your transmitter.
- The indicator light stops flashing and keeps on indicating that the programming has already been set up successfully.
Repeat Steps 1-4 to pair multiple transmitters and receivers.
Cancel Pairing Steps
Cancel all programming so that no remote transmitter can control it:
-
Press the programming button on the receiver until the indicator light begins to flash rapidly
Note : The light flashes from slowly to rapidly. -
Release the programming button and then press it again. The indicator light will be off. All the programming has been canceled.
No Interference
Remote control outlets adopt variable learning codes technology. The codes
will be changed each time after re-programming. If this remote control outlet
happens to be in the same channels as other RF remote devices, just re-program
it and the interference will be eliminated.
Transmitter Timing Settings
Notes : The receiver must be located within 100 feet of the remote transmitter. The actual functional range may be affected by the following factors: weather, radio frequency interference, low remote battery, and obstructions between the transmitter and receiver.
- Transmitter test
- Before setting the transmitter, place the transmitter at the location you want indoors, and then press the ON/OFF button to test if the transmitter could successfully control the receiver.
- Reset
- Before programming, all settings should be reset. The reset hole which is identified by “R” is just located between the “ON” and“OFF” buttons. Use a paper clip or ballpoint pen to stick it.
- Set the Current Time
- Long press the “CLOCK” button for more than 3s until the number on the screen flashes to enter the current time setting interface.
- Press the “HOUR” button to set the hour
- Press the “MIN” button to set the minutes
- After the setting is completed, press the “CLOCK” button to complete the current time setting, and the screen stops flashing.
- ON/OFF Mode
- Press the “ON” button, the timer is always ON, and the screen displays shown in Figure 4-1.
- Press the “OFF” button, the timer is always OFF, and the screen is shown in Figure 4-2.
NOTE : When the ON/OFF mode is activated, the operation of P1, P2, P3, REP, and CTD mode will be automatically stopped
P1/P2/P3 Mode
- Press and hold the P1 button for 3s until the number on the screen flashes to enter the ON time setting interface in the P1 mode.
- Press the HOUR/MIN button to set the ON time in P1 mode.
- Press the P1 button again to enter the OFF time setting in the P1 mode.
- Press the HOUR/MIN button to set the OFF time in P1 mode.
- Press the clock button to complete the setting of P1 mode and return to the current time interface.
- After setting the P1 ON/OFF time,press the P1 button shortly to activate the P1 mode. At this time, the screen displays “P1”, and it will run daily as your settings until be turned off. Short press the P1 button again to end the P1 mode,and the “P1” will disappear
- Repeat the above settings to set P2 and P3 modes.
NOTE : The three modes of P1, P2 and P3 can run at the same time.
P1/P2/P3 Mode Operation Status:
- When the screen displays P1 ON, the current connected device is ON, as shown in Figure 5-1.
- When the screen displays P1 OFF, the current connected device is OFF, as shown in Figure 5-2.
- When the screen displays P1 P2 ON, the P1 P2 mode is running at the same time, and the current connected device is ON, as shown in Figure 5-3. When the screen displays P1 P2 OFF, the P1 P2 mode is running at the same time, and the current connected device is OFF, as shown in Figure 5-4.
REP Mode
REP : Repeat mode, Pre-set turn on or off in cycles within the set time period. For example: Between 8:00 AM – 6:00 PM,set PER ON 1h1min, REP OFF 2h 2min; that is to say, when you activate REP mode, during 8:00 am – 6:00 pm every day, the load will ON 1hour 1minute, OFF 2 hour 2minutes in cycle until you switch to another mode
- Press and hold the REP button for 3s until the number on the screen flashes to enter the ON duration setting, as shown in Figure 6-1.
- Press the HOUR/MIN button to set the ON time in the REP mode.
- Press the REP button to enter the OFF duration setting, as shown in Figure 6-2.
- Press the HOUR/MIN button to set the OFF time.
- Press the REP button to enter the REP mode start time setting, as shown in Figure 6-3.
- Press the HOUR/MIN button to set the start time
- Press the REP button to enter the setting of the end time, as shown in Figure 6-4.
- Press the HOUR/MIN button to set the end time
- Press the clock button to complete the REP mode setting and return to the current time interface.
- After setting the REP mode, Press the REP button shortly to start the REP mode. At this time, the screen displays the word “REP”, and it will run every day according to your settings until you turn it off; Short press the REP button again to cancel the REP mode. At this time, the screen does not display the word “REP”.
REP mode running status:
- When the screen displays REP ON, the current connected device is ON if the REP mode is running, as shown in Figure 6-5.
- When the screen displays REP OFF, the current connected device is OFF during REP mode , as shown in Figure 6-6.
CTD Mode
CTD : Count Down mode, countdown for a preset time once.
- Press and hold the CTD button for 3s until the number on the screen flashes to enter the time setting in the CTD mode.
- Press HOUR/MIN button to set the period of time you want to count down.
- Press the clock button to complete the setting of the CTD mode and return to the current time interface.
- After setting the CTD mode,short press the CTD button to start the CTD mode. At this time, the screen displays the CTD mode duration you have set and starts to count down. On the screen, “CTD OFF” changes to “CTD ON”, as shown in Figure 7-1.
- After the countdown is over, it will automatically return to the current time interface. When CTD is running, short press the CTD button to interrupt the countdown mode.
NOTE : The CTD mode will only run once after it is started, and will not run again the next day. CTD mode can run simultaneously with P1/P2/P3 mode. At this time,P1/P2/P3 mode will continue to run after CTD mode is over.
CTD mode running status:
- When the CTD mode and the P1/P2/P3 mode are running at the same time, the P1/P2/P3 mode will continue to run after the CTD mode ends, as shown in Figure 7-2 (during running) and 7-3 (after the end).
- When only the CTD mode is running, always keep OFF after the CTD mode ends, as shown in Figure 7-4 (during running) and 7-5 (after finishing).
DST Mode
DST : Daylight Saving Time
- Press the DST button, the current time will increase by 1 hour, and the screen will display “+1h”, as shown in Figure 8-1.
- Press the DST button again, the current time is subtracted by 1 hour, and the word “+1h” on the screen disappears, as shown in Figure 8-2.
Low battery reminder
When the screen displays the “ ” mark or the receiver does not work or the
screen characters display dim, you need to replace the battery in time,
otherwise, the product will not work normally, as shown in the figure.
Replace the battery
Open the battery compartment cover on the back of the transmitter, take out the old batteries, install 3×1.5V AA batteries, and close the battery compartment cover.
Specifications
- Input Voltage: 125VAC 60Hz
- Max. Current: 15A Resistive
- 8A tungsten lamp
- Transmission Frequency: 433.92MHz
- Remote Battery: 3×1.5V AA
FCC STATEMENT
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
One-Year Limited Warranty
Supported by our professional R&D team and QC team, we provide One Year Warranty for materials and workmanship from the purchase date. Please note that the warranty does not cover damage caused by personal misuse or improper installation. Please attatch your Order ID and Name so that our dedicated customer service team can help you better.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>