dewenwils HOSL03B WiFi Low Voltage Transformer Instruction Manual

dewenwils HOSL03B WiFi Low Voltage Transformer Instruction Manual

READ ALL INSTRUCTIONS before using the Wi-Fi Low Voltage Transformer.

Mac address: If your router identifies by Mac address, please key in the code number shown in the code label of the unit. i.e., 3x:2x:7x:0x:Cx:Cx

Compatible with 2.4 GHz Wi-Fi networks.

If you have multiple routers in your home, especially under the same modem and using dynamic IP address mode, please notice the routers have same LAN IP address may cause IP address conflict and make the routers involved cannot access internet. Then make Wi-Fi Low Voltage Transformer cannot been discovered and controlled via internet (like user’s cellular data service).

IMPORTANT: Please refer to INSTALLATION INSTRUCTION before proceeding with Wi-Fi router connection. Wi-Fi Low Voltage Transformer must be installed before connecting to Wi-Fi router.

TO CONNECT THE Wi-Fi Low Voltage Transformer TO A WI-FI ROUTER

STEP 1: Scan the QR code to download the ECO app. You can also search “Eco Plug” and download it in the app store.

https://pre.eco-plugs.net/app/eco_plugs.apkhttps://apps.apple.com/cn/app /eco-plugs/id953073532

STEP 2: Reset the Wi-Fi Low Voltage Transformer.

If you decide to connect this device to a new router, or are having trouble setting up this device after multiple attempts, try resetting the Wi-Fi Low Voltage Transformer.

• Press and hold the Power button while pressing the Reset button with the tip of a toothpick or similar non-conductive item. Continue holding the Power button for 3-5 seconds until the Wi-Fi Status Indicator light turns off.
• When the Wi-Fi Status Indicator light turns off, release the Power button and the Wi-Fi Low Voltage Transformer has been reset.
• After a few seconds the Wi-Fi Status Indicator light will begin blinking and the Wi-Fi Low Voltage Transformer is ready to be reconnected to the Wi-Fi router via the app.

This process clears any programmed settings, disconnects the app connection to the Wi-Fi router, and restores the Wi-Fi Low Voltage Transformer to the factory default setting.

STEP 3: Open the Wi-Fi connection settings of the smartphone, select ECO- XXXXXXXX, and click to
connect

STEP 4: Open the ECO app, register an account as required and log in, then close the ECO app.

STEP 5: Open the ECO app, select the home Wi-Fi router that you want to link to the Wi-Fi Low Voltage Transformer.
NOTE: It may take a few seconds for network communication.

STEP 6: Fill in the information (Note: US residents enter your five-digit ZIP code, Canadian residents enter your three-digit telephone number area code). When finished filling in the information, click the SAVE SETTINGS or JOIN button. (In iOS: if you can’t find the JOIN button, click in the “Password” box).

STEP 7: Connection succeeded

The status indicator light will remain on continuously to indicate that Wi-Fi connection has been established and the Wi-Fi Low Voltage Transformer is accessible via the app.

To Add Multiple Users To The ECO APP
Link to the same home router as used by first smartphone or tablet, repeat steps 4 for each additional user.

To Add Additional Wi-Fi Low Voltage Transformers To The APP

Repeat steps 2-7 for each additional Wi-Fi Low Voltage Transformer. Remember to give each transformer a different name (for example, Transformer 1, Transformer 2, Transformer 3, etc.).

Note: You can connect to a maximum of twelve (12) Wi-Fi Low Voltage Transformers via the app.

Selecting Which Device To Control
If you have multiple Wi-Fi Low Voltage Transformers connected to the app, you can choose which device you want to access (such as Transformer 1, Transformer 2, Transformer 3, etc.). To select the device, slide the desired icon to the lower left position. The Wi-Fi Low Voltage Transformer’s name (such as “Transformer 1” below) will change color from white to yellow. Chosen device is now able to be programmed or edited, such as changing timer settings, updating cloud service, etc.

Programming The Timer

• Tap the (9 icon .
• Tap the (±) icon in the upper right corner .
• Select the timer function from the “Set Rules” list.
• Select on/off times for desired hours, minutes and days .
• Tap the checkmark to accept.

Editing The Timer Program

• Tap the  icon .
• 108: Tap the icon. Click the arrow that appears on the right of that setting to enter editing mode.

Android: Select the program to edit, tap and hold until the edit pop-up window appears.

INSTALLATION INSTRUCTIONS

Important safety information to reduce risk of fire injury.

1. Do not install within 10 feet (3 m) of a pool, spa or fountain.
2. There are no serviceable parts inside the power supply unit. DO NOT DISASSEMBLE.
3. Do not repair or tamper with cord or plug.
4. Do not submerge transformer in water.
5. Do not mount the transformer onto combustible material.
6. Do not connect two or more transformers in parallel.
7. Do not use the transformer with a dimmer switch.
8. Plug the power supply unit directly into a GFCI wet location outlet.
9. For use with low voltage outdoor landscape lighting system only.
10. The maximum output of this transformer is 120 watts. Do not overload the transformer. Be sure that the total cumulative wattage of all 12 volt fixtures connected to the transformer is equal to or less than 120 watts.

CAUTION: This landscape light system must be installed in accordance with all local codes and ordinances. If you are experiencing problems, contact a qualified electrician.

CALCULATION LIGHTING CAPACITY

The 120 Watt transformer has 120 watt circuits which will power up to 120 watts of light. To make sure the maximum number of fixtures can be safely connected to this transformer, add up the individual wattages of all the fixtures. The total wattage of your fixtures must not exceed output capacity of the 120 Watt transformer.

INSTALLATION

1. Preparing the Cable
   Being careful when splitting it. NOT to expose the copper cable. Remove the landscape cable insulation 1/2 inch from both cables and twist ends.

2. Connecting the cable to the Transformer
   Lay the transformer on a flat, stable surface and use screwdriver to connect the stripped ends of the cable under the terminal clamping plate.

3. Placing Your Fixtures and Routing the cable
   Lay your fixtures (not included) to your desired location. Be sure they do not exceed the 120-watt rating of the transformer. Coil the rest of the cable after the last fixture.

4. Attaching Your Fixtures
   Tum the transformer on. Use the cable connectors to attach your fixtures with the cable. Then it will light up.

5. Mounting the Transformer
   Use the screw to mount the transformer directly on a wall. 12 inch to 48 inch (0.3 m to 1.2 m) high from the ground would be suggested.

CABLE SELECTION CHART

AWG1 Not recommended for Halogen Landscape.
NOTE: This data is provided as a general guideline. Actual performance ail depend on the installation layout. the fixtures, and the condition of the cable. If the wire diameter you use is thinner than the wire diameter recommended in the table, it may cause the flickering of the end lamps.

SPECIFICATIONS

– Input Voltage: 120VAC, 60Hz
– Output: 12VAC
– Max Power Rating: 120W

Package List

– 1 x Low-Voltage Transformer
– 2 x Screws
– 2 x Wall Anchors
– 1 x Instruction Manual

One-year Limited Warranty
DEWENWILS warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase. Warranty will be void if damage is due to misuse or improper installation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>