MuxLab 500485 HDMI 2.0 Fiber Extender Kit Single Mode User Manual
- June 4, 2024
- MuxLab
Table of Contents
HDMI 2.0 Fiber Extender Kit Single Mode
User Manual
Safety Precautions
- Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.
- Do not dismantle the housing or modify the module. It may result in electrical shock or burns.
- Do not open or remove the housing of the device as you may be exposed to dangerous voltage or other hazards.
- To prevent fire or shock hazards, do not expose the unit to rain, or moisture and do not install this product near water. Keep the product away from liquids.
- Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on the housing, unplug the module immediately.
- Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
- Using supplies or parts not meeting the product specifications may cause damage, deterioration or malfunction.
- Refer all servicing to qualified service personnel.
- Install the device in a place with adequate ventilation to avoid damage caused by overheating.
- Unplug the power when left unused for a long period of time.
- Information on disposal of devices: do not burn or mix with general household waste, please treat them as normal electrical waste.
Copyright Notice
All contents in this manual are copyrighted, and cannot be cloned, copied, or
translated without the express permission of MuxLab Inc. Product
specifications and information n this document are for reference only, and the
content may be updated from time to time without prior notice.
Introduction
The HDMI 2.0 Fiber Extender Kit, Single Mode (model: 500485) allows one HDMI
2.0 and one USB.
1.1 channel to be transmitted up to 10km (6.25miles) at all resolutions up to
4K2K@60Hz over single mode fiber optic cable in a point-to-point
configuration. In addition, the HDMI 2.0 Fiber Extender Kit, Single Mode is
HDCP 2.2 compliant and supports IR and RS-232 pass-through and keyboard/mouse
USB signal transmission.
Features
- Supports HDMI 4K @ 60fps (4:4:4 8bits)
- Supports HDR, which is 4K @ 60fps (4:2:0 10bits)
- Supports HDCP 2.2
- Extends HDMI signals up to 10km over single mode fiber optic cable supports USB 1.1 for keyboard and mouse only
- Supports full frequency IR signal from 20KHz to 60KHz
- Bi-directional IR pass-through
- Link LED indicator light
- Wall mounting housing design for easy and robust installation
! The RS-232, IR and USB function cannot be used at the same time
Package Contents
- One (1) HDMI 2.0 Fiber Extender Kit, Single Mode [TX & RX]
- One (1) IR Blaster
- One (1) IR Receiver
- Two (2) PSU 12V DC
- Two (2) Single Mode Modules
- One (1) Wall bracket kit (with screws)
- One (1) User manual (available via download)
Notes: Confirm that the product and accessories are all included. If not, please contact the supplier from which you purchased the unit.
Specifications
Technical:
| HDMI compliance | HDMI 2.0a |
|---|---|
| HDCP compliance | HDCP 2.2 |
| Video bandwidth | Single-link 594MHz [18Gbps] |
| Video support | HDR 4K2K@60 (4:2:0 10bits) / 4K2K@60 (4:4:4 8bits) |
| Audio support | Surround sound [up to 7.1ch] or stereo digital audio |
| Input TMDS signal | 1.2 Volts [peak-to-peak] |
| Input DDC signal | 5 Volts [peak-to-peak, TTL] |
| ESD protection | Human body model |
±15kV [air-gap discharge] & ±8kV [contact discharge]
PCB stack-up| 4-layer board [impedance control — differential 100Ω;
single 50Ω]
IR pass-thru| Bi-directional
RS-232 support| Yes
Input Ports| Transmitter [TX] 1x HDMI, 1x 3.5mm
Receiver [RX] 1x Fiber, 1x 3.5mm
Output Ports| Transmitter [TX] 1x Fiber, 1x 3.5mm
Receiver [RX] 1x HDMI, 1x 3.5mm
In / Out Ports| Transmitter [TX] 1x RS-232, 1x USB
Receiver [RX] 1x RS-232, 2x USB
HDMI source control| Controllable via IR pass-through from RX to
TX with IR extenders
HDMI connector| Type A [19-pin female]
USB connector| Type A
3.5mm connector| Transmitter [TX] IR receiver / IR blaster
Receiver [RX] IR receiver / IR blaster
Mechanical:
| Housing | Metal enclosure |
|---|---|
| Unit Dimensions (DxWxH) | Transmitter [TX] 4.9″ x 4.4″ x 1.1″ |
(125mm x 112mm x 28mm)
Receiver [RX] 4.9″ x 4.4″ x 1.1″ (125mm x 112mm x 28mm)
Unit Weight| Transmitter [TX] 1.02 lbs (0.46Kg) Receiver [RX]
1.00 lbs (0.45Kg)
---|---
Wall-Mounting Hardware| Wall-mount bracket kit, with screws
Power supply| 12V2A
Power consumption| Max 10W
Operation temperature| 0~40°C [32~104°F]
Storage temperature| -20~60°C [-4~140°F]
Relative humidity| 20~90% RH [no condensation]
Warranty| 2 years
Order Information| 500485 HDMI 2.0 Fiber Extender Kit, Single Mode
(UPC: 627699004852)
Panel Descriptions
6.1 Transmitter Unit
| No | Name | Function Description |
|---|---|---|
| 1 | USB [Host] | Connect to a USB port to the computer for keyboard & mouse |
control
2| RS-232| Connect to a serial port of the device with a DB-9 male-male or
male-female cable
3| Mini USB| For technical support only [firmware update]
4| Dip Switch| PIN # 1| ON []| For system firmware update
---|---|---|---|---
OFF []| Normal
PIN # 2| ON []| USB function ON
OFF []| RS-232/IR function ON
PIN # 3| ON []| Disable IR function
OFF []| Enable IR function
5| LED Indicator| [Red]: Power LED indicator [Green]: Link LED indicator
6| SFP OUT| Plug in single mode fiber optic cable that needs to be linked to
th receiver unit
7| HDMI IN| Connect to a HDMI source with a HDMI male-male cable
8| IR Receiver| 3.5mm IR socket to plug in the IR receiver extension cable
9| IR Blaster| 3.5mm IR socket to plug in the IR blaster extension cable
10| +12V DC| Connect to a 12V power supply unit
6.2 Receiver Unit
| No | Name | Function Description |
|---|---|---|
| 1 | USB [Device] | Connect to USB keyboard & mouse |
| 2 | RS-232 | Connect to serial port of the device with a DB-9 male-male or male- |
female cable
3| Mini USB| For technical support only [firmware update]
---|---|---
4| Dip Switch| PIN # 1| ON []| For system firmware update
OFF []| Normal
PIN # 2| ON []| USB function ON
OFF []| RS-232/IR function ON
PIN # 3| ON []| Disable IR function
OFF []| Enable IR function
5| LED Indicator| [Red]: Power LED indicator [Green]: Link LED indicator
6| SFP IN| Plug-in single mode fiber optic cable that needs to be linked to
the transmitter unit
7| HDMI OUT| Connect to an HDMI display with an HDMI male-male cable
8| IR Receiver| 3.5mm IR socket to plug in the IR receiver extension cable
9| IR Blaster| 3.5mm IR socket to plug in the IR blaster extension cable
10| +12V DC| Connect to a 12V power supply unit
Connection Diagram
(Note: IR sensor and emitter not shown in the above diagram.)
HDMI Pin Definition
| Pin 1 | TMDS Data2+ | Pin 11 | TMDS Clock Shield |
|---|---|---|---|
| Pin 2 | TMDS Data2 Shield | Pin 12 | TMDS Clock— |
| Pin 3 | TMDS Data2- | Pin 13 | CEC |
| Pin 4 | TMDS Datal+ | Pin 14 | Reserved (N.C. on device) |
| Pin 5 | TMDS Data1 Shield | Pin 15 | SCL |
| Pin 6 | TMDS Data- | Pin 16 | SDA |
| Pin 7 | TMDS Data0+ | Pin 17 | DDC/CEC Ground |
| Pin 8 | TMDS Data° Shield | Pin 18 | +SV Power |
| Pin 9 | TMDS Data0— | Pin 19 | Hot Plug Detect |
| Pin 10 | TMDS Clock+ |
Troubleshooting
The following table describes some of the symptoms and possible solutions regarding HDMI 2. Fiber Extender Kit, Single Mode
| Symptom | Probable Cause | Possible Solutions |
|---|---|---|
| No Image | No Power | Check power connections |
| No Image | Fiber optic cable | Check the fiber optic cable |
| No Image | HDMI Cable | Check the HDMI cable |
| No Image | Cable length | Check cable length, check with another monitor. |
| Flickering Image or bad sound | Cable length | Check cable length / Check the |
HDMI cable.
USB not working, but the audio/video OK| USB cable or too much power is
required for the USB peripherals.| Check USB cable or try another USB device.
If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at 877-6895228 (toll-free in North America) or (+1) 514-905-0588 (International).
MuxLab Inc.
2321 Rue Cohen
Montreal, Quebec
Canada H4R 2N7
Tel.: +1 514-905-0588 Fax: +1
514-905-0589
Toll-Free (North America): 877 689-5228
URL: www.muxlab.com
E-mail: info@muxlab.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>