DEWENWILS 009 Remote Control Instruction Manual
- June 3, 2024
- dewenwils
Table of Contents
009 Remote Control
Instruction Manual
Operating Instructions
Notes: The receiver must be located within 100 feet of the remote transmitter. Actual functional range may be affected by the following factors: weather, radio frequency interference, low remote battery, and obstructions between the transmitter and receiver.
- Remove the isolation tap in the battery compartment on the transmitter.
- Plug the receiver into a powered outlet.
- Plug your device into the socket of the receiver.
- To control your matching devices:
- Press the ON/OFF button on the transmitter.
- Or press the programming button on the receiver.
- The indicator light of the receiver turns on when the unit is activated.
To program a remote transmitter and receiver
- Plug the receiver into the socket.
- Press and hold the program button on the receiver until the indicator light starts to blink slowly.
- Release the program button, then press the on/off button on the transmitter.
- When the indicator light stops flashing, the program is paired successfully.
Repeat Step 1-4 to pair multiple transmitters and receivers.
Cancel All Programming
Cancel all the programs so that no remote transmitter can control it.
-
Press and hold the program button on the receiver until the indicator light starts to blink rapidly.
Note: The indicator light blinks from slow to fast. -
Release the program button, then press it again, the indicator light will go off, which means cancel the program successfully.
No Interference
Remote control outlets adopt variable learning codes technology.The codes will
be changed each time after re-programming. If this remote control outlet
happens to be in the same channels with other RF remote devices, just re-
program it and the interference will be eliminated.
Battery Replacement
If you find the receivers works abnormally or the indicator on the remote
control becomes dim, please replace the battery.
- Open the battery compartment and remove the old battery.
- Install a new CR2032 battery, making sure the polarity +/- of the battery is correct.
- Close the battery compartment.
Specifications
- Transmission Frequency: 433.92 MHz
- Remote Control Range : 100 Feet (Free Area)
- Remote Battery: CR2032 3V
FCC STATEMENT
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does 03cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISEDC Warning:
This device complies with Innovation, Science, and Economic Development Canad
licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.
One Year Limited Warranty
Supported by our professional R&D team and QC team, we provide One Year
Warranty for materials and workmanship from the purchase date.
Please note that the warranty does not cover damage caused by personal misuse
or improper installation.
Please attatch your Order ID and Name so that our dedicated customer service
team can help you better.