ROCK SLIDE AX-SP-300-JL4 Step Slider Skid Plate Instruction Manual
- June 12, 2024
- ROCK SLIDE
Table of Contents
ROCK SLIDE AX-SP-300-JL4 Step Slider Skid Plate
Product Information
- Made in the USA
- Product Name: 3.0 STEP SLIDER SKID PLATES – 4 DOOR
- Model Numbers: AX-SP-300-JL4, AX-SP-300-JK4
- Newest feature: Skid Plate (Pair) Drive Rivet 5/16 – 18 Carriage Bolt 5/16 Washer 5/16 – Nylock Nut
- Hardware Quantity: 2 Skid Plates, 8 Drive Rivets, 6 Carriage Bolts, 6 Washers, 6 Nylock Nuts
Product Usage Instructions
Step 1: REMOVE STEP SLIDER RSE TAG
- Using a size 7/64 drill bit, remove the two rivets on your step sliders Rock Slide tag.
- It will be replaced by the tag pre-installed on the outside of your skid plates.
- Repeat on both sides.
Step 2: PLACING YOUR SKID PLATE
- The skid plate will layer on top of your step sliders, similar to a phone case.
- There are three square holes near each bracket where your 5/16 carriage bolts will be placed.
- Hold the bolt in place and secure with a washer and Nylock nut.
- Repeat on both sides.
Step 3: INSTALLING DRIVE RIVETS
- Remove Step Slider Plugs if they are placed.
- Pound the rivets by using a hammer.
- Repeat on both sides.
You are done! Scan this code to leave us a review!
See our FAQ on the next page for any troubleshooting or give us a call!
Warranty Policy
- The warranty set forth herein is the only warranty covering the product. No other warranty exists, express or implied, including, without limitation, implied warranties of merchantability and/or fitness for a particular purpose.
- This warranty shall be void in its entirety if RSE determines that the product installation was modified, changed, altered, customized or in any way used other than as instructed. Installation of the product without strictly adhering to the installation instructions shall void this warranty. Installation must be on the proper vehicle or warranty is void.
- For questions or concerns, please contact our office at 435-752-4580 and ask for the warranty department or email us at warranty@rockslideengineering.com.
Newest feature
40% stronger with High Strength Low Alloy Steel (HSLA).
HARDWARE
Description| Quantity
Skid Plate (Pair)| 2
Drive Rivet| 8
5/16” – 18 Carriage Bolt| 6
5/16” Washer| 6
5/16” – Nylock Nut| 6
REMOVE STEP SLIDER RSE TAG
Using a size 7/64 drill bit, remove the two rivets on your step sliders Rock
Slide tag. It will be replaced by the tag pre-installed on the outside of your
skid plates. Repeat on both sides 
PLACING YOUR SKID PLATE
- The skid plate will layer on top of your step sliders, similar to a phone case. There are three square holes near each bracket where your 5/16” carriage bolts will be placed. Hold the bolt in place and secure with a washer and
- Nylock nut.
- Repeat on both sides.
INSTALLING DRIVE RIVETS
- Remove Step Slider Plugs if they are placed.
- Pound the rivets by using a hammer.
- Repeat on both sides
You are done!
Scan this code to leave us a review!
See our FAQ on the next page for any troubleshooting or give us a call!
WARRANTY POLICY
LIMITED TWELVE (12) MONTH WARRANTY FOR FINISH AND ELECTRICAL COMPONENTS
- Rock-Slide Engineering, LLC (“RSE”) warrants to the original purchaser that (a) the structural and mechanical com-ponents of the Step Sliders will be free of defects in material and workmanship for the lifetime of the Step Sliders (the “product”), and (b) the finish (powder coat) and the electrical components (including the motor) will be free of defects in material and workmanship for a period of twelve (12) months from the original date of purchase. This warranty applies only to the original retail pur-chaser. Warranty is void if product was not purchased directly from R- SE or from an authorized RSE retailer or reseller. This warranty applies only with regard to the product as originally installed to the original vehicle. This warranty does not cover removal or reinstallation of the product.
- To exercise this warranty and receive any warranty service, the original purchaser must provide RSE with proof of purchase and date of purchase that is acceptable to RSE, such as a copy of the original purchaser’s purchase receipt. The original purchaser must return the defective product to RSE along with a description of the problem, a copy of the original purchase receipt, the original bill of sale and all contact information (name, address, telephone number and email address). To begin the warranty process, the original purchaser must email RSE’s warranty department. During this warranty term, and upon the original purchaser’s valid exercise of this warranty, RSE shall, at its option, repair or furnish the replacement product in the event the original product is deemed by RSE to be defective. RSE’s sole liability shall be for repairing or replacing the product, but RSE may refund the purchase price at its sole discretion and option. The original purchaser is responsible for prepayment of all shipping and/or transportation charges with respect to the exercise of this warranty. The product may change without notice. In the event of a product change, RSE has no obligation to upgrade or modify any older generation product.
- THE WARRANTY SET FORTH HEREIN IS THE ONLY WARRANTY COVERING THE PRODUCT. NO OTH-ER WARRANTY EXISTS, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, IMPLIED WAR-RANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE. No retailer, reseller, dealer, agent, or employee is authorized to make any modifications, extensions, amendments, or additions to this war-ranty.
- This warranty shall be void in its entirety if RSE determines that the product installation was modified, changed, al-tered, customized or in any way used other than as instructed. Installation of the product without strictly adhering to the installation instructions shall void this warranty. Installation must be on the proper vehicle or warranty is void.
- RSE SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, UNDER ANY LEGAL THEORY AND/OR UNDER ANY CIRCUMSTANCE WHATSOEVER. IN ANY EVENT, ANY DAMAGES IN ANY SITUATION SHALL BE LIQUIDATED DAMAGES AND MAY NOT EXCEED THE RETAIL PRICE OF THE PRODUCT. RSE SHALL NOT BE LIABLE FOR ANY LOSS, DAMAGE OR INJURY DIRECTLY OR INDIRECTLY ARISING FROM THE USE OF OR INABILITY TO DETERMINE THE USE OF THE PRODUCT. THE ORIGINAL PURCHASER IS RESPONSIBLE TO DETERMINE THE SUITABILITY OF THE PRODUCT FOR ITS INTENDED USE, PRIOR TO USING THE PRODUCT, AND THE ORIGINAL PUR-CHASER ASSUMES ALL RESPONSIBILITY AND RISK IN CONNECTION THEREWITH.
- For questions or concerns: please contact our office at 435-752-4580 and ask for the warranty department or email us at warranty@rockslideengineering.com.
ROCKSLIDEENGINEERING.COM – NEED ASSISTANCE? 435.752.4580
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>