ROCK SLIDE ENGINEERING AX-SP-300-BR4 Step-Slider Skid Plate Installation Guide
- June 13, 2024
- ROCK SLIDE ENGINEERING
Table of Contents
Made in the USA
INSTALLATION MANUAL
BRONCO 4 DOOR SKID PLATES
2021 – PRESENT
AX-SP-300-BR4
AX-SP-300-BR4 Step-Slider Skid Plate
NEW Skid Plates for the Ford Bronco Step Sliders!
HARDWARE
| Description | Quantity |
|---|---|
| Skid Plate (Pair) | 2 |
| Drive Rivet | 8 |
| 5/16” – 18 Carriage Bolt | 6 |
| 5/16” Washer | 6 |
| 5/16” – Nylock Nut | 6 |
Step 1 REMOVE STEP SLIDER RSE TAG
Using a size 7/64 drill bit, remove the two rivets on your step sliders Rock
Slide tag. It will be replaced by the tag pre-installed on the outside of your
skid plates. Repeat on both sides.
Step 2 PLACING YOUR SKID PLATE
The skid plate will layer on top of your step sliders, similar to a phone
case. There are three square holes near each bracket where your 5/16” carriage
bolts will be placed. Hold the bolt in place and secure with a washer and
Nylock nut. Repeat on both sides. 
Step 3 INSTALLING DRIVE RIVETS
Remove Step Slider Plugs if they are placed.
Pound the rivets by using a hammer.
Repeat on both sides
You are done!
Scan this code to leave us a review!
See our FAQ on the next page for any troubleshooting or give us a call! 
https://sotellus.com/r/rock-
slide-engineering/
WARRANTY POLICY
LIMITED TWELVE (12) MONTH WARRANTY FOR FINISH AND ELECTRICAL COMPONENTS
Rock-Slide Engineering, LLC (“RSE”) warrants to the original purchaser that
(a) the structural and mechanical components of the Step Sliders will be free
of defects in material and workmanship for the lifetime of the Step Sliders
(the “product”), and (b) the finish (powder coat) and the electrical
components (including the motor) will be free of defects in material and
workmanship for a period of twelve (12) months from the original date of
purchase. This warranty applies only to the original retail purchaser.
Warranty is void if product was not purchased directly from R- SE or from an
authorized RSE retailer or reseller. This warranty applies only with regard to
the product as originally installed to the original vehicle. This warranty
does not cover removal or reinstallation of the product.
To exercise this warranty and receive any warranty service, the original
purchaser must provide RSE with proof of purchase and date of purchase that is
acceptable to RSE, such as a copy of the original purchaser’s purchase
receipt. The original purchaser must return the defective product to RSE along
with a description of the problem, a copy of the original purchase receipt,
the original bill of sale and all contact information (name, address,
telephone number and email address). To begin the warranty process, the
original purchaser must email RSE’s warranty department. During this warranty
term, and upon the original purchaser’s valid exercise of this warranty, RSE
shall, at its option, repair or furnish the replacement product in the event
the original product is deemed by RSE to be defective. RSE’s sole liability
shall be for repairing or replacing the product, but RSE may refund the
purchase price at its sole discretion and option. The original purchaser is
responsible for prepayment of all shipping and/or transportation charges with
respect to the exercise of this warranty. The product may change without
notice. In the event of a product change, RSE has no obligation to upgrade or
modify any older generation product.
THE WARRANTY SET FORTH HEREIN IS THE ONLY WARRANTY COVERING THE PRODUCT. NO
OTHER WARRANTY EXISTS, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
No retailer, reseller, dealer, agent, or employee is authorized to make any
modifications, extensions, amendments, or additions to this warranty.
This warranty shall be void in its entirety if RSE determines that the product
installation was modified, changed, altered, customized or in any way used
other than as instructed. Installation of the product without strictly
adhering to the installation instructions shall void this warranty.
Installation must be on the proper vehicle or warranty is void.
RSE SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, UNDER ANY LEGAL THEORY AND/OR UNDER ANY CIRCUMSTANCE WHATSOEVER. IN
ANY EVENT, ANY DAMAGES IN ANY SITUATION SHALL BE LIQUIDATED DAMAGES AND MAY
NOT EXCEED THE RETAIL PRICE OF THE PRODUCT. RSE SHALL NOT BE LIABLE FOR ANY
LOSS, DAMAGE OR INJURY DIRECTLY OR INDIRECTLY ARISING FROM THE USE OF OR
INABILITY TO DETERMINE THE USE OF THE PRODUCT. THE ORIGINAL PURCHASER IS
RESPONSIBLE TO DETERMINE THE SUITABILITY OF THE PRODUCT FOR ITS INTENDED USE,
PRIOR TO USING THE PRODUCT, AND THE ORIGINAL PURCHASER ASSUMES ALL
RESPONSIBILITY AND RISK IN CONNECTION THEREWITH.
For questions or concerns: please contact our office at
435-752-4580 and ask for the warranty
department or email us at
warranty@rockslideengineering.com.
ROCKSLIDEENGINEERING.COM
NEED ASSISTANCE?
435.752.4580 – PAGE 4
REVISED 10/19/2021
Documents / Resources
| ROCK
SLIDE ENGINEERING AX-SP-300-BR4 Step-Slider Skid
Plate
[pdf] Installation Guide
AX-SP-300-BR4 Step-Slider Skid Plate, AX-SP-300-BR4, Step-Slider Skid Plate,
Skid Plate, Plate
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>