saxby lighting 72369 Linear Pro 6ft Twin Light Instruction Manual
- June 13, 2024
- saxby lighting
Table of Contents
72369 Linear Pro 6ft Twin Light
Instruction Manual
Instruction leaflet
Linear Pro
72364, 72365, 72366, 72367, 72368, 72369
72369 Linear Pro 6ft Twin Light
Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and satisfactory operation of this product. Please retain these instruction for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building
Regulations.
To prevent electrocution switch off at mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge. If you are in any doubt, please consult a
qualified electrician .
If replacing an existing fitting, make a careful note of the connections.
This product is rated at IP20.
This light fitting contains non-replaceable parts and cannot be serviced.
If damage occurs the part should be discarded.
This product is not dimmable.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Specification
| Voltage: | 240V 50Hz a.c. |
|---|---|
| Lamp: | 72364 : 31.5W LED module – 41 0Olm |
72365 : 47.5W LED module – 6200Im
72366 : 54.5W LED module – 71 0Olm
72367 : 57W LED module – 7 400lm
72368 : 77W LED module – 9900Im
72369 : 90W LED module- 11500Im
IP rating:| 20
Layout
- This product can be installed on the ceiling or wall.
- Ensure the ceiling or wall is capable of holding the weight of the product
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires
-
Remove both end caps by pushing in the clips with a small screwdriver or similar tool.
-
Starting from one end and working along, remove the LED panel and diffuser unit by gently squeezing the sides of the metal body and lifting off the diffuser unit to one side.
-
Hold the product in place and mark the position of the fixing holes. This may require the help of an assistant.
If wall mounting, ensure that the product is level. -
Ensure the ceiling or wall is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
-
Feed the supply cable through the centre hole and fix the light fitting into position.
-
Connect the supply cable to the quick fit terminal block as below
Wiring
Having correctly identified the wiring from your existing light fitting,
connect to the connection block inside the product in the following way:
Check that …
- You have correctly identified the wires
- The connections are tight
- No loose strands have been left out of the connection block.
Commissioning
- Connect the LED driver output cable to the LED panel, ensuring it is securely clipped together.
- Refit the LED panel and diffuser unit by clipping it into place ensuring the sides are aligned with the body. Take care not to trap any cables.
- Refit the end caps ensuring they are clipped into position.
- Replace fuse or circuit breaker and switch on. Your light is now ready for use..
Fitting/replacing bulbs
- The LEDs in this fitting are non-replaceable.
- If any damage occurs this fitting should be discarded.
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
Recycling advice
waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Safety information
Live Voltages may be present in this unit even when turned off or when
completely disconnected.
For your safety, always switch off the power supply before cleaning.