saxby lighting 10401 Mini Crescent Wall Light Instruction Manual

: June 13, 2024
: saxby lighting

Table of Contents

saxby lighting 10401 Mini Crescent Wall Light
Product Information
Product Usage Instructions
Specification
Layout
Installation
Wiring
Commissioning
Safety information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

saxby lighting 10401 Mini Crescent Wall Light

saxby-lighting-10401-Mini-Crescent-Wall-Light-PRODUCT

Product Information

Product Name: Mini Crescent Wall
Model Number: 10401
Manufacturer (UK): BH17 7BY
Manufacturer (EU): Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
Website: www.saxbylighting.com
Voltage: 220-240V 50Hz a.c.
IP Rating: 20
Maximum Bulb Wattage: 40W E27 GLS
Double Insulated: Yes

Product Usage Instructions

Commissioning:
- Position the product by fixing it to the wall using nuts and washers.
- Ensure that the terminal block is properly located in the recess in the wall back.
- The light is now ready for use.
Fitting/Replacing Bulbs:
- When changing a bulb, always switch off the mains power and allow the bulb to cool before handling.
- Do not dispose of used bulbs with household waste; please recycle them where facilities exist.
- Use the correct type and wattage bulb. The maximum recommended bulb wattage is 40W E27 GLS.
- To fit a new bulb, insert it into the fitting and twist it clockwise to secure.
Cleaning:
- We recommend cleaning the product with a soft dry cloth.
- Avoid using solvents, liquids, or abrasive cleaners as they may damage the finish and the product.
Recycling Advice:
- Do not dispose of waste electrical products with household waste; please recycle them where facilities exist.
- Check with your local authority or retailer for recyclingadvice.
Safety Information:
- Always switch off the power supply before changing lightbulbs or cleaning for your safety.
- If you are unsure, consult a qualified electrician.

Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and satisfactory operation of this product. Please retain these instruction for future reference.

Warning

This product is Double Insulated and does not require connection to an Earth circuit.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
If replacing an existing fitting, make a careful note of the connections.
Always use the correct type and wattage bulb.
Exceeding the bulb wattage will damage the product.
When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully and responsibly.
This product is suitable for dimming when used in conjunction with a dimmable lamp. Please ensure verification of dimming abilities with the lamp manufacture prior to use.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Specification

Voltage: 220-240V 50Hz a.c.
Lamp: 1 x Max. 40W E27 GLS
IP rating: 20

Layout

Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box and the light fitting
Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged Mount out of arms reach.
Cables in walls must be protected using suitable conduit or plastic trunking.
The mains supply cable must have a minimum cross sectional area of 1.0mm?

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.

Hold the product in place and mark the location of the fixing holes. Ensure that the product is level.
Ensure the wall is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
Using the supplied screws, screw into the wall until the collar just touches.
Wire as detailed below.

Wiring

This unit is double insulated and must not be earthed. If there are any incoming earth cables, they must be joined together and well insulated with good quality insulation tape. This is to ensure earth continuity throughout your property.
Having correctly identified the wiring from your existing light fitting and connect to the connection block inside the product in the following way:

Check that…

You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.

Commissioning

Ensure that the terminal block cover is clipped back into position.
Line the product up with the screws in the wall.
Ensure that the terminal block is properly located in the recess in the wall back.
Gently slide the product into position. Using the domenuts and washers fix to the wall.
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Fitting/replacing bulbs

When changing a bulb, always swith off at the mains and allow the bulb to cool before handling. Used bulbs should not be disposed of with household waste. Please recycle where facilities exist.
Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting.
Unscrew the bulb anti clockwise to remove.
Carefully locate the bulb in the lampholder and turn clockwise to secure.

We recommend cleaning with a soft dry cloth.
Do not use solvents, liquids or abrasive cleaners as these could damage the finish and the product.

Recycling advice
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.