onninen LEDVANCE T8 LED Tube Light Instruction Manual

June 13, 2024
onninen

onninen LEDVANCE T8 LED Tube Light

Product Information

Model Number Wattage Voltage Frequency Rated Current Length
4975000 CNI441 18W 220-240V~ 50/60Hz 80mA 1212mm
4975001 CNI440 24W 220-240V~ 50/60Hz 110mA 1513mm
4975002 CZC374 18W 220-240V~ 50/60Hz 80mA 1212mm
4975003 CZC375 24W 220-240V~ 50/60Hz 110mA 1513mm

Product Usage Instructions

To ensure proper and safe usage of the LED Tube T8, please follow the instructions below:

  1. Make sure to use the correct model number and wattage according to your needs.
  2. Connect the LED tube to the appropriate voltage of 220-240V~.
  3. Ensure the frequency is set to 50/60Hz.
  4. Take note of the rated current for the LED tube.
  5. Install the LED tube according to its specified length (1212mm or 1513mm).
  6. Refer to the wiring diagram for proper installation.
  7. Use the provided LED starter to prevent mixing up during future maintenance.
  8. Dispose of the product responsibly by recycling it at a collection point or contacting the seller for proper disposal.

Please consult the product manual for any additional information or troubleshooting steps.

Technical specification

Odel Number| 4975000 CNI441 T8G1-ML-18W 4000K| 4975001 CNI440 T8G1-ML-24W 4000K| 4975002 CZC374 T8G1-ML-18W 3000K| 4975003 CZC375 T8G1-ML-24W 3000K
---|---|---|---|---
Wattage| 18W| 24W| 18W| 24W
Voltage| 220-240V~| 220-240V~| 220-240V~| 220-240V~
Frequency| 50/60Hz| 50/60Hz| 50/60Hz| 50/60Hz
Rated Current| 80mA| 110mA| 80mA| 110mA
Length| 1212mm| 1513mm| 1212mm| 1513mm

Cautions

  • Read the entire manual carefully before installation and operation.
  • Only licensed and qualified electricians are allowed to perform the installation.
  • Before the installation or replacement of the lamp, turn it off and allow it to cool down. Heat-resistant gloves are mandatory when handling the tube.
  • The LED T8 tube can be used to replace the traditional fluorescent T8 tube with G13 lamp base and corresponding length mentioned in theabove table.
  • Onnline LED T8 tube cannot work with electronic ballast.
  • The LED starter should be used with the LED T8.
  • Lamp is suitable for 50Hz or 60Hz operation.
  • Dimming is not allowed.
  • To replace the fluorescent T8 tube, the existing starter has to be removed together with the tube. A LED starter is provided to work with LED tube.
  • The minimum safety distance from the illuminated object is 0.1m.
  • Any constructive change of the luminaire in case of applying retrofit LED lamp shall not be permitted.
  • The lamp should be used in dry conditions or in a luminaire that provides protection.
  • The lamp is not suitable to be used in emergency luminaires designed for the double-capped fluorescent lamp(s).
  • This lamp may not be suitable for use in all applications where a traditional fluorescent lamp has been used. The temperature range of this lamp is more restricted. In cases of doubt reqarding the suitability of the application the manufacturer of this lamp should be consulted.
  • No modifications of the luminaire which the LED lamp is to be used with are to be made.
  • The manufacturer accepts no liability for any damages resulting from the misuse of the lamp or when it is used with inappropriate equipment.
  • Consult your dealer for any enquiries.

Attentions

  • Instant start is allowed.
  • The LED T8 tube is designed for general lighting service (excluding for example explosive atmosphere).
  • The overall energy efficiency and light distribution are determined by the installation design.
  • The operating temperature of LED T8 tube is -20°C to +45°C.

Part list
LED tube x 1 and LED starter x 1

Installation

onninen LEDVANCE T8 LED Tube Light-fig1

Wiring diagram

onninen LEDVANCE T8 LED Tube Light-fig2

Correct Disposal of This Product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return vour used device.please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

The LED T8 tube is designed for general lighting service (excluding for example explosive atmosphere).

www.onninen.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals