Onninen CNH788 Universal Luminaire Base LED 300 mm IP44 User Manual
- June 10, 2024
- onninen
Table of Contents
- CNH788 Universal Luminaire Base LED 300 mm IP44
- Product Information: Universal Luminaire Base LED 300 mm IP44 CNH788
- Removal Of Light Source
- General Safety Information
- Disposal
- ADVICE ON DISPOSAL
- Advice on Disposal
- Product Usage Instructions
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CNH788 Universal Luminaire Base LED 300 mm IP44
Product Information: Universal Luminaire Base LED 300 mm IP44 CNH788
INSTALLATION INSTRUCTION
Removal Of Light Source
This product contains light source which has energy efficiency class E.
The Universal Luminaire Base LED 300 mm IP44 CNH788 is a lighting fixture that operates on 230V and is equipped with LED lights. It has a protection class 1 symbol, which indicates that it should be connected to the network side with the yellow/green protective earth to the protective earth terminal. The light source is replaceable by a professional, but the control gear is non- replaceable. It has an IP44 rating, making it suitable for use in damp environments.
General Safety Information
Electrical installations should only be carried out by qualified electricians. Before proceeding with installation, the mains connecting cable must be de- energized (fuse turned off). Do not make any changes to the lamp or its connecting cable. Do not operate the lamp if it or its connecting cable show visible signs of damage. Only clean lights when turned off, do not allow any moisture into connecting areas or on current-carrying parts. Cleaning agents can cause staining. Please note! Before proceeding with installation mains connecting cable must be de-energized (fuse turned off). Please note the following symbols and safety instructions, in order to avoid damage caused by incorrect assembly or use:
Protection class 1: Lamps with this symbol connect them on the network side with the yellow/green protective earth to the protective earth terminal
Changes: Do not make any changes to the lamp or its connecting cable.
Commissioning : Do not operate the lamp if it or its connecting cable
show visible signs of damage.
Care advice: Only clean lights when turned off, do not allow any moisture
into connecting areas or on current-carrying parts. Cleaning agents can cause
staining.
Disposal
Do not dispose of the waste electric appliances together with household waste. In conformity with the directive 2012/19/EN on waste electrical and electronic equipment and its implementation in the national laws, waste electrical and electronic equipment should be collected separately and transferred for environmentally safe reuse. Recycling as an alternative to the requirement of return: the owner of the electrical and electronic equipment parting with the ownership is obliged to return it or to co-operate in the appropriate utilization of the equipment. For this purpose, the waste appliance may also be brought to a take-back station for disposal in accordance with the national recycling requirements and the legal acts concerning waste handling.This does not apply to the accessory parts and auxiliaries of the waste appliances, except for the electric components.
ADVICE ON DISPOSAL
In the interests of environmental protection, when you have no further use for your product, do not dispose of it along with household waste, but take it to a proper disposal facility. Information on waste disposal depots and their opening times can be obtained from your local authority. Faulty or used batteries must be recycled in accordance with Directive 2006/66/EC. Please return batteries and/or device to the specified collection points.
Advice on Disposal
In the interests of environmental protection, when you have no further use for your product, do not dispose of it along with household waste, but take it to a proper disposal facility. Faulty or used batteries must be recycled in accordance with Directive 2006/66/EC. Please return batteries and/or device to the specified collection points.
Product Usage Instructions
- Ensure that the mains connecting cable is de-energized (fuse turned off) before proceeding with installation.
- Connect the luminaire to the network side with the yellow/green protective earth to the protective earth terminal.
- Insert the replaceable LED light source (by a professional) or turn the luminaire on if the LED light source is already installed.
- Use a 10mm cable gland to connect the luminaire to the mains supply. The cable should have a cross-sectional area of 1-1.5mm2.
- Turn the luminaire off before removing the light source.
Manufacturer
Onninen Oy,
Onninen 28, 02-295 Warszawa,
www.onninen.pl