onninen COW488 Onnline Modular Luminaire Onnpanel II Instruction Manual
- June 4, 2024
- onninen
Table of Contents
Modular Luminaire
Onnpanel II
Instruction manual
SPECIFICATION PARAMETER (GB)
Model number| COW488 / 4202513 IPL-FP122C40A1-34UL40W2| COW489 / 4202514 PL-
FP122C40A1-34UL40W2
---|---|---
Dimension(mm)| 595 x 595 x 11| 595 x 595 x 11
Wottage| 34W| 34W
Voltage| 220-240V| 220-240V
Frequency| 50/60Hz| 50/60Hz
Luminous flux| 4000 Im| 4100 Im
Control| DALI| On-Off
Color temperature| 4000K| 4000K
Ta| 25 °C| 40 °C
IP level| IP20| IP20
Important safety instruction
To ensure correct function and safety, please read and follow all instruction carefully before using the product, Basic safety precautions should always be followed when installing, including the following:
- Turn off power supply before installation or before doing any maintenance, cleaning, changing the globe or adjustment to the fitting.
- Do not install any luminaire near the heat source.
- IP grade please refer to product label, only IP54 can be used in wet or damp locations.
- Do not exceed the nominal supply voltage or amperage ratings.
- All wiring and installation of the light fitting must adhere to local and national wiring rules.
- Take care not to pull any electrical wires during unpacking as this may damage the connection.
- Lay out all the components on a smooth surface and make sure three are no components missing before assembling.
- To avoid injury or damage to the fitting, please ensure that power leads and screws are secure before connecting the power.
- If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
- Please keep instruction for future reference.
Warning :
- Only for indoor use, protecting from high magnetic, voltage and thunder surrounding.
- Correct wiring, and securely installed.
- Only use in rated voltage.
- Cut off the power source before connect the wires.
- Should not be installed without valid documents.
- Please ask for help from professional electrician when installation.
- Would not get the quality assurance if unauthorized dismantling of the product.
Installation Procedure
-
- Option 1:
Dali version
Option 2:
on/off version
6.
- Option 1:
-
Cut off the power source before installation.
Carefully unpack unit and properly inspect for defects before installing. -
Remove the ceiling tile from the location where you wish to install the LED PANEL.
-
Make electrical connections from power supply according the wire connection instruction.
-
/
-
Place the fixture in the appropriate T-bar ceiling structure.
-
Reconnect the main power supply.
Disposal
Do not dispose of the waste electric appliances together with household waste.
In conformity with the directive 2012/19/EN on waste electrical and electronic
equipment and its implementation in the national laws, waste electrical and
electronic equipment should be collected separately and transferred for
environmentally safe reuse.
Recycling as an alternative to the requirement of return: the owner of the
electrical and electronic equipment parting with the ownership is obliged to
return it or to co-operate in the appropriate utilization of the equipment.
For this purpose, the waste appliance may also be brought to a take-back
station for disposal in accordance with the national recycling requirements
and the legal acts concerning waste handling.This does not apply to the
accessory parts and auxiliaries of the waste appliances, except for the
electric components.
ADVICE ON DISPOSAL
In the interests of environmental protection, when you have no further use for
your product, do not dispose of it along with household waste, but take it to
a proper disposal facility. Information on waste disposal depots and their
opening times can be obtained from your local authority. Faulty or used
batteries must be recycled in accordance with Directive 2006/66/EC. Please
return batteries and/or device to the specified collection points.
| This symbol explains that the lamp is not suitable
for covering with thermal insulating material.
---|---
| Non-replaceable light source
| Replaceable control gear by a professional
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
This product contains light source which has energy efficiency class D.
Onninen Oy
Työpajankatu 12, FI- 00580 Helsinki
www.onninen.com
Manual instructions material
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>