ROPOX TF 200.0059 4Single Table Frame User Manual

4SingleManual
User Manual
Mounting Instructions

Keep this folder with product at all times!
TF 200.0059_uk / 09-03-2023 / Rev 01

Introduction

4Single is a multi-function table, which may be adjusted to suit seated or standing activities.
Owing to the unique design there are a variety of applications and the table is therefore also ideal for wheelchair users.
This document must ALWAYS accompany the product and be read by and available to users.
All users must follow these instructions. It is very important that the instructions have been read and understood prior to operation of the product.
These instructions must always be available to the user and must accompany the product in case of relocation.
Correct use, operation and inspection are decisive factors for efficient and safe performance.
The operation must be made or supervised by an experienced adult, who has read and understood the importance of section 8 ”Safety in use”

Application

4Single is designed to obtain optimum working height for the user. It is an activity table and not for use as a lifting table or person lifter.
The product must be used indoor, under room temperatures and humidity as stated in section 3. 4Single is not designed for use in damp rooms.

Conformity with EU Directive and UK Directive

This product has CE marking and is thus in accordance with the basic requirements concerning functionality and safety of the current EU Directive. See separate CE declaration.
This product has UKCA marking. See separate Declaration of Conformity

Technical data

Height 55-85cm / 21,6 – 33,4in H1
50-41110
Height 65-95cm / 25,6 – 37,4 in H2
50-41210
Front fascia’s for frame L = xxx cm
50-42xxx
From 60-300cm in increments of 1cm
From 23,6-118,1in in increments of 0,4in
Side fascia’s for frame W = xxx cm
50-44xxx
From 60-200cm in increments of 1cm
From 23,6-78,7in in increments of 0,4in
Options:| Wheels:
Increase the table height by 6.5cm / 2.5in
Material:| Welded steel tubes St. 37 and various plastic components
Surface treatment:| Blue chromate, powder coating: Standard CWS 81283 RAL 7021 mat
Max. load of frame:| 150kg / 330lb evenly distributed
Temperature:| 5-45° C
Air humidity:| 5-85% (non-condensing)
Complaints:| See page 12
Producer:| Roopa A/S, DK-4700 Nested, Tel.: +45 55 75 05 00
E-mail: info@ropox.dk – www.ropox.com

Schematic diagram of frame

All connections to the table must be flexible to ensure that the table moves freely within the range of adjustment.

Component

1. Gearbox
2. Shaft adapter, outside Hex7, inside Hex6
3. Side fascia shaft, Hex6. Length = frame width – 13.8cm/5,4in
4. Gearbox for crank handle, Fixture & Bushing
5. Front fascia shaft, Hex7. Length = frame length – 16.7cm/6,5in
6. Leg 1
7. Leg 2
8. Handle
9. Allen screw M8x16
10. Side fascia profile, Length = frame width – 12.4cm/4,9in
11. Front fascia profile, Length = frame length – 12.4cm/4,9in
12. Stop ring incl. screw
13. Screw ø4.8×13, Torx
14. Cover plate

Item No.
96000656
3012999-047
3012999-148
2060320-297
95010003
98000-555
95091012
5040000-025| Pcs.
2
4
2
1
1
2
2
1
16
2
2
2
2
4
---|---

Mounting instructions, illustrations

Mounting must always be carried out by competent personnel.
Prior to mounting, check that all parts have been provided. See list of components, section 6.
5.1 Assembly of frame

6.1.1 Check that the height (L) of all four legs is identical. May be adjusted on hexagonal shaft by means of the open-end wrench provided. Place side fascia’s on a plane surface and mount legs. See label on legs.

6.1.2 At the opposite end of the handle fit a stop ring on either side of the angular gear. Do not tighten the stop rings till the frame has been assembled.

6.1.3 Now mount the two front fascia’s.
Tighten the bolts securely by means of the wrench provided.

6.1.4 Place the frame on the table top and push the cover plates between legs and table top. Centre the frame in relation to the table top.

6.1.5 Fix the table top with screws through the holes of the fascia’s.
5.2 Mounting of wheels (option)

6.2.1 Mount the wheels. Do not forget to fit three washers on each wheel.

List of components

Set of legs H1, 50-41110:
Set of legs H2, 50-41210:
Front fascias for L=xxx cm, 50-42xxx:
Shaft Hex7 (fascia length – approx. 5cm/2in)
Side fascias for W=xxx cm, 50-44xxx:
Shaft Hex6 (fascia width + ca.2.5cm/1in)
Handle for 4Single 50-47010-9:
Gearbox 96000656:
Shaft adapter 3012999-047:
Gearbox for handle 3012999-148:
The Gearbox contains:
Gearbox 96000688
Fixture for shaft extension 3012999-051
Bushing 3012999-052
Allen screw M8x16 95010003:
Screw ø4.8×13 95091012:
Stop ring incl. screw 30*65500-084:|
---|---

Options

Brake wheels, black (4 wheels) 50-41600:
Increase the table height by 6.5 cm2,5in incl. 12 washers (95170510)

Safety in use

➢ 4Single must only be used by persons, who have read and understood these instructions.
➢ 4Single is an activity table and should not be used as a lifting table or person lifter,
➢ Always use the table in a manner excluding the risk of damage to persons or property. The person operating the table is responsible for avoiding damage or injury.
➢ Children or persons with reduced observation capability should only operate the table when supervised.
➢ If the table is used in publicly accessible locations where children or persons with reduced observation capability may get near the table, the person operating the table must pay attention to those present in order to prevent dangerous situations.
➢ Make sure that there is free space above and below the table to allow height adjustment.
➢ Do not operate the table in case of defects or damage.
➢ Do not overload the table and make sure that the load distribution is correct.
➢ Do not use the table in an explosive environment.
➢ In connection with inspections, service or repairs always remove weight from the table.
➢ Modifications, which may influence the operation or construction of the table, are not allowed.
➢ Installation, service and repairs must be carried out by competent personnel.
➢ If the table has not been assembled according to these mounting instructions the right to complain may become void.
➢ Only use Roopa original spare parts as replacement parts. If other spare parts are used, the right to complain may become void.

Cleaning/ maintenance

9.1 Cleaning of frame
Clean the frame with a wrung cloth with lukewarm water and a mild detergent. Do not use enchants or abrasives or grinding cloths, brushes or sponges.
Dry the frame after cleaning.
9.2 Maintenance
Inspections, service and repairs must be carried out by competent personnel.
The frame is maintenance-free and the moving parts have been lubricated for life. For reasons of safety and reliability we recommend inspection of the frame once a year:
➢ Check that all bolts have been securely tightened.
➢ Check that the table moves freely from bottom to top position.
After each inspection, fill in the service schedule.
Only use Ropox original spare parts for replacement of parts. If other spare parts are used, the right to complain may become void.
9.3 Service schedule, operation and maintenance

Service and maintenance Serial No.
Date:
Signature:
Remarks:| Service and maintenance Serial No.
Date:
Signature:
Remarks:
---|---
Service and maintenance Serial No.
Date:
Signature:
Remarks:| Service and maintenance Serial No.
Date:
Signature:
Remarks:
Service and maintenance Serial No.
Date:
Signature:
Remarks:| Service and maintenance Serial No.
Date:
Signature:
Remarks:
Service and maintenance Serial No.
Date:
Signature:
Remarks:| Service and maintenance Serial No.
Date:
Signature:
Remarks:

Complaints

See General Terms of Sale and Delivery on www.ropox.com

ROPOX A/S
Ringstedgade 221
DK – 4700 Nested
Tel.: +45 55 75 05 00 Fax.: +45 55 75 05 50
E-mail: info@ropox.dk
www.ropox.com
TF 200.0059_uk

References

• Ropox - World's leading disability friendly solutions
• Ropox - World's leading disability friendly solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>