EnGenius DuraFon SIP System with ONSIP Sip Service User Guide

June 7, 2024
EnGenius


How to Configure an EnGenius DuraFon
SIP System with ONSIP Sip Service.

EnGenius DuraFon SIP System with ONSIP Sip -

First, you will need the following Hardware Equipment.

  1. EnGenius DuraFon SIP SystemEnGenius DuraFon SIP System with ONSIP Sip - 1
  2. Broadband Router with Internet Access
    Once everything is set up and connected, you are ready to set up the SIP Service.

Logging into SIP Base unit Gui

FIRST, you will need to change the LAN settings on the computer that is going to be used to set up the SIP Base Station.

  1.  Go to the Network and Sharing Center and click on “Change adapter settings”EnGenius DuraFon SIP System with ONSIP Sip - Network and sharing
  2.  Right-click on Local Area Connection and go to PropertiesEnGenius DuraFon SIP System with ONSIP Sip - Right click
  3. Select the internet protocol version 4 (TCP/IPv4)EnGenius DuraFon SIP System with ONSIP Sip - internet protocol.
  4.  Select: Use the following IP address (also known as a static IP address)EnGenius DuraFon SIP System with ONSIP Sip - IP address

Input: 192.168.1.15 for the IP address and  255.255.255.0 for the subnet mask and press OK.

You are now ready to configure the EnGenius DuraFon SIP System.

Registration of Handsets

Before setting the SIP configuration, the available handset(s) of the DuraFon- SIP must register to the base.

Register Handset:

  1. Press and hold the register key on the base until the “INTERCOM” LED changes to a flashing status. The base can perform the handset registration while the LED is flashing.
  2. On the handset, enter “MENU, 7,1” to enter the registration.
  3. The assigned ID (from 10 to 19) will be displayed on the handset LCD, indicating successful registration.
  4. Repeat the above steps for all additional handsets.

Once you have successfully registered your handsets to the base unit, you can now go ahead and log in to the SIP Base Unit Go to any of your preferred Internet Browser  (Internet Explorer/Firefox/Safari/Chrome) and enter the IP Address: 192.168.1.156

Once prompted to the EnGenius DuraFon SIP Log in page type:
Username: admin
Password: admin

EnGenius DuraFon SIP System with ONSIP Sip - adminOnce you have entered the correct username and password, click the Login button to open the web-based configuration page.

Go to the LAN Tab settings
EnGenius DuraFon SIP System with ONSIP Sip - LAN Tab
settingsAs shown, its default setting is on the Static IP address.
It is recommended to set the LAN in DHCP mode
EnGenius DuraFon SIP System with ONSIP Sip - 2Once you click apply, it will reboot the device for 39 seconds
EnGenius DuraFon SIP System with ONSIP Sip - 39
seconds Note: When you change the LAN IP to DHCP, once you click Apply, the change will take effect. You will need to revise your new IP Address from the DHCP Clients on your network.
Go back to the TCP/IP properties tab and select
– Obtain an IP address automatically
– Obtain DNS server address automatically

EnGenius DuraFon SIP System with ONSIP Sip - IP
properties

With this step, you will be able to log in to your EnGenius DuraFon SIP base through DHCP.
For demonstration purposes, we have used an example of an EnGenius Router, where it showed us the DHCP Client list and our new DHCP IP address to access the Durafon SIP base unit.

EnGenius DuraFon SIP System with ONSIP Sip - SIP base
unit Once obtained the new IP address, we can log in and continue with our setup.

EnGenius DuraFon SIP System with ONSIP Sip - new IP
address

Once you are on the main menu, click on the VoIP Tab and click on the Basic Tab.

EnGenius DuraFon SIP System with ONSIP Sip - configuration
pageIn this section, is where you will need to set up your SIP Account Service information, in this case, we will be using our ONSIP Service.
*The key information needed to establish a connection with the OnSip Service are the following:

VoIP Server IP: engenius.onsip.com
VoIP Server Port: 5060
Local Sip Port: 5060
SIP Outbound Proxy: sip.onsip.com
SIP Outbound Proxy Port: 5060EnGenius DuraFon SIP System with ONSIP Sip -
SIP Outbound

*Everything else stays default, unless requires by the VoIP service provider
Once you have entered the correct information, you can press APPLY.

  • Please note that the information used in this section is for demonstration purposes, you will need to have a SIP Account Service Provider (In this case we used OnSIP Hosted  PBX) or a SIP server to set this up.

Now Go to the Account Setting Tab.

EnGenius DuraFon SIP System with ONSIP Sip - SIP Account Users
\(

In this section, is where your SIP Account Users (Extensions) will need to be registered.
Up to 10 Sip Accounts can be registered on an EnGenius DuraFon SIP Base Unit.
*By default, all accounts are disabled, as you add accounts, you will need to enable them as you go.

Please follow the following steps to add SIP Accounts.

  1. Press the edit tab under the “Action menu”.
  2. Once you are in the user information settings, the fields that need to be filled are the following”

.

  1. SIP Number : In this field, you will type in your “Username” given by the On Sip service provider.
  2. Display Name: In this field, you can input any name you wish; this will be like the caller id name it will show on the recipient’s phone screen.
  3. Auth Name: In this field, is where you input the Auth Username given by the SIP Provider.
  4.   Password: In this field, you will input the password supplied by the SIP Service, In this case the SIP PASSWORD on your OnSIP Account.

EnGenius DuraFon SIP System with ONSIP Sip - SIP
PASSWORD

I the window below, it shows the OnSIP account information setting.

EnGenius DuraFon SIP System with ONSIP Sip - SIP- Reg
Status

Once you have inputted the correct Login information press Apply If you successfully inputted the information, you should get a green light on “ SIP- Reg Status ”. This indicates that the account is active.

EnGenius DuraFon SIP System with ONSIP Sip - Apply 2Scroll Down and Press “APPLY” to save all changes.
EnGenius DuraFon SIP System with ONSIP Sip - APPLY

You have successfully registered a SIP account, if you need to add more Sip Accounts extensions, follow the steps.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals