teesa TSA5051 Steam Mop Owner’s Manual
- June 13, 2024
- teesa
Table of Contents
teesa TSA5051 Steam Mop
Thank you for purchasing TEESA appliance. Read this instruction manual and keep it for future reference. Producer does not take responsibility for damages caused by inappropriate handling and use of the product
DESCRIPTION
- Handle
- Water tank cap
- Power cable
- Power mode button
- LED indicators
- Mop head
- Carpet attachment
- Hook
- Tube
- Steam leaner
- Release button
- Steam release button
- Adapter
- Crevice tool
- Round brush
- Scraper
- Crevice brush
- Cup
- Cloth
SAFETY INSTRUCTIONS
In order to reduce the risk of injuries or damages, follow basic safety precautions applied when using any electrical device, including the following:
- Read the entire instruction manual before you start installation and assembly and keep it for future reference. Keep the manual for future reference.
- Before connecting the device to power supply socket, make sure the voltage indicated on the device corresponds to the voltage in the power supply socket.
- Appliance for household use only.
- Clean and store this device in accordance to instructions listed in Cleaning and m section.
- ALWAYS turn off the device and disconnect it from the mains supply:
- if it’s not operating correctly
- if there’s an uncommon voice when using
- before cleaning
- when not in use
- before filling water tank
- When you disconnect the power cord of the device, grasp and pull the plug, not the cord/ cable.
- This device cannot be used by children below 12 and by people who cannot express their intentions.
- Keep the device out of the reach of children.
- Keep the device and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
- Make sure the power cord does not touch any hot or sharp elements.
- Do not use the product for purpose different from displayed in this operating manual.
- Do not place the appliance in water or any liquid, do not use it with wet hands.
- Do not use this device if the cord or the plug is damaged, or the appliance is broken..
- Do not attempt to repair this device yourself. Only authorized and qualified personnel may repair this device. Never disassemble this device.
- Use only authorized accessories.
- Do not add any detergents to water- this may damage the device.
- Do not cover the steam outlet during operation.
- It is forbidden to apply the device to the body during work – risk of burns.
- Some elements of the mop, such as the nozzle or attachments, heat up to very high temperatures. Do not touch them during operation – risk of burns.
MOUNTING THE DEVICE
- Insert the handle shaft into the opening at the top of the main body with the inset pointed towards the back. Push it in until you hear it click into place.
- To put the device in a standing position, lift up the main body into a vertical position until the inset on the tube inserts into the groove on the floor head and locks the mop in place
OPERATION
-
Attach a dedicated cloth to the bottom of the mop head. To do this, place the pad on the floor, white side up, fit the mop head to the edges of the pad and push down on it.
-
Unscrew the cap of the water tank and fill it using the included cup.
Note : It is recommended to use demineralized or distilled water – this will help keep the device working longer. -
Plug power cable to the main socket.
-
The LED indicators will flash until the mop motor reaches the temperature needed for operation. After about 25 sec. the device is ready to use.
-
To start steam generation, hold the mop head with your foot and tilt the device back. The operation of the engine will be audible. Steam will begin to come out of the nozzle at the bottom of the mop head.
-
To switch between power modes, press the power mode button until the desired mode is selected.
-
To stop steam generation, turn the device to the vertical position.
-
The device can also be used to freshen carpets. To do that, mount plastic carpet attachment on the mop head:
-
put the attachment on the floor, the side with latches up,
-
insert the floor head into the front part of the attachment, so the front edges of the floor head are neatly aligned with the edges of the attachment,
-
push the mop down until the plastic latches at the back of the attachment clamp down on the floor head.
-
Further steps are the same as for standard floor cleaning. Do not use carpet attachment to clean smooth surfaces.
STEAM CLEANER OPERATION
- To remove the steam cleaner from the mop body, press the two release buttons located at the bottom of the tube at the same time, and then the steam cleaner should be tilted slightly forward and pulled upward.
- Unscrew the cap of the water tank and fill it using the included cup.
- Attach the adapter to the steam outlet on the steam cleaner and then apply the nozzle so that the tabs slide into the grooves in the slot, then turn clockwise until the nozzle locks onto the adapter. To remove the adapter, press the buttonon it and slide it off the steam cleaner.
- To switch between power modes, press the power mode button until the desired mode is selected.
- Press and hold the steam release button to start dispensing steam.
CLEANING AND MAINTENANCE
IMPORTANT : Before cleaning, disconnect the device from main socket and wait for it to cool down.
- Clean this device with a soft, slightly damp cloth.
- Do not use any chemical agents to clean this device.
- Cloths can be washed in the washing machine
SPECIFICATION
MAIN FEATURES
- For multiple hard floor types
- Carpet refreshing function
- Steam cleaner function
- Large cloth
- Tilt and swivel arm
- Arm lock in an upright position
- 3 steam power levels
- Steam ready indicator
TECHNICAL DATA
- Power: 1500 W
- Pressure: 1 bar
- Water tank capacity: 380 ml
- Steam rate: 15 / 21 / 28 ml/min
- Heating up time: 25 sec.
- Noise level: 60 dB
- Power supply: 220 – 240 V AC, 50 Hz
PHYSICAL PARAMETERS
- Power cable length: 5 m
- Weight: 3,0 kg
- Dimensions: 30 x 25 x 110 cm
IN SET
Textile pad 2 pcs, carpet slider, water cup, conic tool, round brush, crevice
brush, curvednozzle, scraper
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or its literature,
indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400
Miętne
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>