StarTech.com VS321HDBTK Multi-Input HDMI Over HDBaseT Extender User Manual

StarTech.com VS321HDBTK Multi-Input HDMI Over HDBaseT Extender

Compliance Statements

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other

Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgment elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Safety Statements

Safety Measures

• Wiring terminations should not be made with the product and/or electric lines under power.
• Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.

Product Diagram

Transmitter Front View

Port
2| Infrared Sensor| •           Receives infrared signals for remote control of the Extender
3| Status LED Indicator| •           Indicates the status of the Transmitter
4| Input Selection Buttons| •           Select an active HDMI Input Port
5| Standby Button| •           Enter or exit Standby Mode**

Transmitter Rear View

RJ11 to RS232 Adapter for Serial Control
8| EDID Copy Button| •           Copy EDID Settings from the HDMI Source Device
9| Mode Switch| •           Switch between Manual , Automatic and

Priority HDMI Source selection

10| HDMI Input Ports| •           Connect HDMI Source Devices
11| System Ground| •           Connect a Grounding Wire to prevent a ground loop.
12| Video Link Output Port| •           Connect the Receiver via CAT5e/6 Cable
13| EDID LED Indicator| •           Indicates the EDID Copy status

Receiver Front View

Receiver Rear View

Receiver

(located on the top of the Receiver )

17| System Ground| •           Connect a Grounding Wire to prevent a ground loop.
18| Video Link Input Port| •           Connect the Transmitter via CAT5e/6 Cable

Requirements

• HDMI Source Devices (up to 4K @ 30 Hz) x 3
• HDMI M/M Cables (sold separately) x 4
• HDMI Display Device x 1
• CAT5e/6 Cable x 1
• (Optional) Grounding Wires x 2
• (Optional) Hex Tool x 1

For the latest requirements and to view the full User Manual, please visit www.startech.com/VS321HDBTK.

Installation

Note: Ensure the HDMI Display Device and the HDMI Source Devices are powered off before you begin the installation.

1. Peel and stick the Rubber Feet onto the bottom of the Transmitter and Receiver.

2. (Optional – grounding) Turn the Screws of the System Grounds counterclockwise using a Phillips Head Screwdriver.

   • For applications using loose Electrical Cable:
   • Do not loosen the Screw(s) all the way. Wrap the Electrical Cable around the Screw(s) before retightening the Screw(s).
   • For applications using specialized Grounding Wires:
   • Loosen the Screw(s) all the way and insert the Screw(s) through the Grounding Wire ends before retightening into the Transmitter and Receiver.

3. (Optional – grounding) Connect one end of your Grounding Wires to the System Ground on the Transmitter and Receiver and the other end to the Earth Grounds in your Building.

4. Connect an HDMI Cable (sold separately) to an Output Port on the HDMI Source Device and to one of the HDMI IN Ports on the Transmitter.

5. Repeat step #4 for each of your remaining HDMI Source Devices.
   Note: Each HDMI Input Port is numbered, please take note of which number is assigned to each HDMI Source Device.

6. Connect a CAT5e/6 Cable to the Video Link Output Port on the Transmitter and to the Video Link Input Port on the Receiver.

7. Connect an HDMI Cable to the HDMI Output Port on the Receiver and to an HDMI Input Port on the HDMI Display Device.

8. Connect the Universal Power Adapter to an available Power Source and to the Power Adapter Port on either the Transmitter or the Receiver.
   Note: VS321HDBTK uses Power over Cable (PoC) to provide power to both units when the Universal Power Adapter is connected to either the Transmitter or Receiver.

9. Power on your HDMI Display, followed by each of your HDMI Source Devices.

10. (Optional – for Serial Control) Connect the RJ11 to RS232 Adapter to the Serial Control Port on the Transmitter and to a Serial Port on your Computer.

(Optional) Mounting

Mounting the Transmitter

1. Determine the Mounting Surface for the Transmitter.
2. Place the Mounting Brackets on either side of the Transmitter. Align the Holes in the Mounting Brackets with the Holes in the Transmitter.
3. Insert two Screws through each Mounting Bracket and into the Transmitter. Tighten each Screw using a Phillips Head Screwdriver.
4. Mount the Transmitter to the desired Mounting Surface using the appropriate Mounting Hardware (e.g. Wood Screws).

Mounting the Receiver

1. Determine the Mounting Surface for the Receiver.
2. Remove the Rubber Feet on the bottom of the Receiver.
3. Flip the Receiver upside down and place it on a clean and flat Surface.
4. Place one Mounting Bracket on the bottom of the Receiver. Align the Holes in the Mounting Bracket with the Holes in the bottom of the Receiver.
5. Insert two Screws through the Mounting Bracket and into the Receiver.
6. Mount the Receiver to the desired Mounting Surface using the appropriate Mounting Hardware (ex. Wood Screws).

Operation

LED Indicators

Port LED Indicators

LED Behavior| Status
Solid blue| Non-HDCP HDMI Source selected
Flashing blue| Non-HDCP HDMI Source not selected
Solid purple| HDCP HDMI Source selected
Flashing purple| HDCP HDMI Source not selected
Solid red| No HDMI Source selected
Status LED Indicator

LED Behavior| Status
Solid green| The device is powered & HDBaseT is not linked
Solid blue| HDBaseT is linked
EDID LED Indicator

LED Behavior| Status
Flashing two times| EDID copy
Flashing three times (long flash – short flash – short flash)| Auto EDID

Mode Switch

The Mode Switch, located on the rear of the Transmitter, is used to determine how the current Source is selected. Toggle the Mode Switch to one of the following three settings.

( HDMI Input 1 , 2 , then 3 )

Auto| Auto-select the last connected

HDMI Source

Switch| Select the HDMI Source using the

Input Selection Buttons

EDID Settings

Function

|

Action

| Status LED Indicator (While Holding Button)| Status LED Indicator (During Playback)
---|---|---|---

Copy and store

| Press and Hold EDID Copy Button for 3 Seconds|

Flashing green rapidly

|

Flashes twice

Auto migration

| Press and Hold EDID Copy Button for 6 Seconds|

Flashing green slowly

|

Flashes three times

Restore the 1080p preset EDID setting and enable auto migration| Press and Hold EDID Copy Button for 12 Seconds|

Flashing green rapidly

|

Flashes three times

Standby Mode

In Standby Mode the video transmission is disabled and the Transmitter and Receiver go into a low power mode.

• To enter Standby Mode: Press and Hold the Standby Button for 3 seconds.
• To exit Standby Mode: Press and Release the Standby Button.

Remote Control

Remote Control can be used to remotely select your HDMI Source Device and to change the Standby Mode settings. The Remote Control operates through line-of- sight. Always point the Remote Control directly at the infrared sensor on the Transmitter, with no objects obstructing the signal path.

• To enter or exit Standby Mode: Click the x10 Button once.
• To select an HDMI Source Device: Click M1, M2, or M3 for HMDI Sources 1 to 3.

Note: All other buttons are not functional.

Input Selection Buttons

Press and release the Input Selection Button, located on the front of the Transmitter, to select the desired HDMI Source Device. The LED Indicator for the selected HDMI Input Port will light up and the selected HDMI Source Signal will display on the HDMI Display Device.

Manual Operation with Serial Control Port

1. Configure the settings using the Serial Control Port with the values shown below.
   • Baud Rate: 38400 bps
   • Data Bits: 8
   • Parity: None
   • Stop Bits: 1
   • Flow control: None
2. Open a third-party Terminal Software to communicate through the Serial Control Port and use the on-screen commands, displayed on the next page, to operate and configure the Transmitter and Receiver.

On-Screen Commands

Options

1.  Copy from specified monitor a1

2.  Copy from corresponding monitor (1 on 1)

3.  Make 1024 x 768 EDID

4.  Make 1280 x 800 EDID

5.  Make 1280 x 1024 EDID

6.  Make 1360 x 768 EDID

7.  Make 1400 x 1050 EDID

8.  Make 1440 x 900 EDID

9.  Make 1600 x 900 EDID

10.  Make 1600 x 1200 EDID

11.  Make 1680 x 1050 EDID

12.  Make 1920 x 1080 EDID

13.  Make 1920 x 1200 EDID

14.  Make 1920 x 1440 EDID 15 Make 2048 x 1152 EDID

when n= 1: a1: monitor index (1~2). a2: not required when n = 2: a1.a2: not required

when n = 3~15: a1: video options

1.  DVI

2.  HDMI(2D)

3.  HDMI(3D) a2: audio options

1.  LPCM 2 ch

2.  LPCM 5.1 ch

3.  LPCM 7.1 ch

4.  Dolby AC3 5.1 ch

5.  Dolby TrueHD 5.1 ch

6.  Dolby TrueHD 7.1 ch

7.  Dolby E-AC3 7.1 ch

8.  DTS 5.1 ch

9.  DTS HD 5.1 ch

10.  DTS HD 7.1 ch

11.  MPEG4 AAC 5.1 ch

12.  5.1 ch combination

13.  7.1 ch combination

n : 1~max – output port n.- All ports

VS| View current settings
Eq=n| Set EQ level as n (1~8)
FACTORY| Reset as factory default setting
REBOOT| Reboot the device
RCID=n| Set Remote Control ID as n

n: 0- Reset as null(Always on) 1~16 – Valid ID

IT=n| Set terminal interface n: 0 – Human

167 – Machine

LCK=n| Lock / Unlock device n: 0 – Unlock

167 – Lock

Warranty Information

This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees, or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you. Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.

StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.

Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools. StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom, and Taiwan servicing a worldwide market.

Reviews

Share your experiences using StarTech.com products, including product applications and setup, what you love about the products and areas for improvement.

StarTech.com Ltd. 45 Artisans Cres. London, Ontario N5V 5E9 Canada

• FR: startech.com/fr
• DE: startech.com/de

StarTech.com LLP 2500 Creekside Pkwy. Lockbourne, Ohio 43137 U.S.A.

• ES: startech.com/es
• NL: startech.com/nl

StarTech.com Ltd. Unit B, Pinnacle 15 Gowerton Rd., Brackmills Northampton NN4 7BW United Kingdom

• IT: startech.com/it
• JP: startech.com/jp

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

FREQUENTLY ASKED QUESTIONS

What is the StarTech.com VS321HDBTK Multi-Input HDMI Over HDBaseT Extender?

The StarTech.com VS321HDBTK is a multi-input HDMI over HDBaseT extender that allows you to extend HDMI signals over long distances using HDBaseT technology.

What is the maximum transmission distance supported by the extender?

The extender can transmit HDMI signals up to a maximum distance of 70 meters (230 feet) over a single Cat5e or Cat6 Ethernet cable.

How many HDMI inputs does the extender have?

The StarTech.com VS321HDBTK extender has three HDMI inputs, allowing you to connect multiple HDMI sources.

Can I switch between different HDMI inputs using the extender?

Yes, the extender features a switch that allows you to select between the three HDMI inputs and transmit the selected input over the HDBaseT link.

What is HDBaseT technology?

HDBaseT is a technology that enables the transmission of uncompressed high- definition video, audio, and control signals over long distances using standard Ethernet cables.

What is the maximum supported resolution for video transmission?

The extender supports video resolutions up to 1080p (1920x1080) at 60Hz, providing high-quality video output.

Can the extender transmit audio signals as well?

Yes, the StarTech.com VS321HDBTK extender can transmit both video and audio signals over the HDBaseT link.

What type of Ethernet cable is required for the HDBaseT link?

The extender requires a Cat5e or Cat6 Ethernet cable for the HDBaseT transmission. Cat6 cables are recommended for longer distances and better performance.

Does the extender support IR (infrared) control?

Yes, the extender supports IR control, allowing you to control the HDMI source devices remotely from the display location.

Can I use this extender with a network switch or router?

No, the VS321HDBTK extender is designed for point-to-point connections and does not work with standard network switches or routers.

Does the extender support RS-232 control?

Yes, the extender supports RS-232 control, providing a convenient way to control devices over the extended distance.

Can I use this extender for 4K video transmission?

No, the StarTech.com VS321HDBTK extender supports video resolutions up to 1080p and does not support 4K video transmission.

Does the package include both the transmitter and receiver units?

Yes, the package includes both the transmitter and receiver units required for the HDMI over HDBaseT extension.

Is the extender compatible with HDCP (High-bandwidth Digital Content Protection)?

Yes, the extender is HDCP compliant, allowing you to transmit protected content from HDMI sources to the display.

Can I use this extender for long-distance installations in commercial settings?

Yes, the extender is suitable for long-distance installations in commercial settings, such as conference rooms, classrooms, and digital signage applications.

Download the PDF Link:StarTech.com VS321HDBTK Multi-Input HDMI Over HDBaseT Extender User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>