saxby lighting 46395 Shale CCT Wall Light Instruction Manual
- June 13, 2024
- saxby lighting
Table of Contents
Shale CCT Wall
46395
Instruction manual
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Check the pack and make sure you have all the parts listed.
Install in accordance with the IEE Wiring regulations and current Building
Regulations.
To prevent electrocution switch off at mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge. If you are in any doubt, please consult a
qualified electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
These product should not be fitted to PIR circuits or short duration timed
switches.
If replacing an existing fitting, make a careful note of the connections.
This product contains non-replaceable parts and cannot be serviced. If damage
occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will
reach the distance between the junction box and the light fitting.
Avoid locating any cables in positions that would cause a hazard. Position
cables and junction boxes (not supplied) away from areas where they may be at
risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross sectional area of 1.0mm 2
Cables must be protected using suitable conduit or plastic trunking.
This product is not moisture proof, and should not be used in bathrooms.
Installation
Existing fittings must be completely removed before installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
Note that the switch is turned off before installation.
- Undo the side screws and remove the wall back from the product.
- Hold the wall back in position and mark the location of the fixing holes.
- Ensure the wall is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick or cavity walls. Ensure that the wall back is level.
- Fit the wall back in position.
- Wire as detailed wiring diagram.
- Lift the front part of the product into place and fix using the side screws.
- Replace fuse or circuit breaker and switch on. Your light is now ready for use.
**
**Wiring
Having correctly identified the wiring from your existing light fitting, pull
the wire through the hole and connect to the connection block inside the
product in the following way: 
Check that…
- You have correctly identified the wires.
- The connections are tight.
- No loose strands have been left out of the connection block.
Technical data
Supply Voltage: 220-240 V~, 50 Hz
Bulb Type: 9W LED module (SMD) CCT, 3500/5000K
This product contains a light source of energy efficiency class F.
Non-replaceable light source
Replaceable control gear by a professional
Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
This product is Class 1, must be connected to earth.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
local store for recycling advice.
This product is not suitable for dimming.
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish.
For your safety, always switch off the power supply before cleaning.
This LED’s are protected by a glass lens. The lens part must be replaced
immediately should it become cracked or damaged. This fitting must not be used
without the glass lens in place.
For further information, please visit https://www.lighting-info.co.uk/46395
www.saxbylighting.com
V4 20/06/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>