ROSWELL Cybox Bluetooth Interface Receiver Instruction Manual

June 4, 2024
ROSWELL

Cybox Bluetooth Interface Receiver

Cybox Parts & Hardware

Tools Required
===llCJ)
Phillips Screwdriver
Precision Screwdri·,;ar

‘ ‘
A

‘ ‘ ‘ ‘
3.SMMto

x4

RCA Cable

Electrical Tape Wire Strippers

PLEASE NOTE: The Cybox Bluetooth device utilizes a line driver that produces a high voltage output to provide a top quality listening experience. If you intend on using the Cybox as an auxiliary input, please be aware that is has an integrated switch that can be used to lower the output voltage of the Cybox if necessary. See page 4 for more information.
INSTALLING THE CYBOX AS A STANDALONE UNIT

Disconnect positive cable(s) from battery/batteries.

·

Find a suitable location to mount your Cybox. Ensure

Tape the end(s) with electrical tape to prevent an

·

that it is installed in an area that will stay dry and keep

accidental short circuit.

~ – · the wires from being snagged or pulled out

Install a switch or locate an existing one to power on
the Cybox. This 12V+ wire will run from the switch to . _ . . the “R” terminal on the Cybox.

I

Connect the power wires as shown below:

C)l’.box Port
B+ BR DR

Wire Colour
Yellow Black Red Blue

Function
Constant 12V + Ground Switched 12V+ Delayed remote to amplifier

Please Note: The 12V+ should come from a 3a inline fuse. Note: Roswell recommends using marine-quarrty 18AWG wire for connecting to your Cybox. Ensure all wires are secure by giving each one a gentle pull after tightening.

WWWuROSWEL,.L~WAKEAIRoCOITT
J you have any questions please call : 1-855-962-WAKE(9253)

Rev. ‘i!O-Jul-14 Pg. 1/4

Connect the Cybox to your amplifier supplied 3.5mm to RCA connector.

Verify that all wires are properly and securely connected. Reconnect the positive battery cable(s) .
Tum on the switch installed for your Cybox.

NOTE: If multiple amplifiers are being used you may purchase additional cables by calling your local Roswell Marine Audio Dealer and asking for part# C720-0003.

STANDALONE UNIT

NOTE: to reduce the risk of a ground loop, which can negatively affect sound quality, please ensure the Cybox and all audio
components share a common ground point.
e PAIRING: Open the Bluetooth settings on your device. Scan for Bluetooth devices. Choose “Roswell Cybox” on your device. (You may see a MAC address or “MISC” before Roswell Cybox appears)

IMPORTANT: Make sure the volume is down on your device before playing music. Give the Cybox a few seconds before pressing “PLAY” on your device in order for the output to sync with the new connection. If you press “PLAY” too early there may be no sound.

You are now ready to listen to your music wirelessly via the Roswell Marine Audio Cybox.

INSTALLING THE CYBOX AS AN AUXILIARY-INPUT DEVICE (Connected to a head unit or other receiver)

Disconnect positive cable(s) from battery or batteries. Tape the end(s) with electrical tape to prevent an accidental short circuit.

Find a suitable location to mount your Cybox. Ensure that it is installed in an area that will stay dry and keep the wires from being snagged or pulled out.

If you have any questions please call : ‘i-855-962-WAKE(9253) ( } Rev. 10-JuI-14 Pg. 2/4

Cybox Port
B+
8-
R DR

Wire Colour
Yellow Black Blue Empty

Function
Constant 12V + Ground Head Unit Remote

Please Note: The 12V+ should come from a 3a inline fuse. Note: Roswell recommends using marine-quality 18AWG wire for connecting to your Cybox. Ensure all wires are secure by giving each one a gentle pull after tightening.
Verify that all wires are properly and securely connected. Reconnect the positive battery cable(s).
Turn on the head unit and choose the correct source (auxiliary input) .

Connect the Cybox to the head unit’s auxiliary input RCAs using the supplied 3.5mm to RCA connector. Be sure the 3.5mm end is plugged into the correct leftmost output as shown below.
Note: If your audio device utilizes a 3.5mm auxiliary input please use a 3.5mm to 3.5mm cable (not included) to make the connection.

AUXILIARY-INPUT DEVICE
NOTE: to reduce the risk of a ground loop, which can negatively affect sound quality, please ensure the Cybox and all audio
components share a common ground point.
PAIRING: Open the Bluetooth settings on your device. Scan for Bluetooth devices. Choose “Roswell Cybox” on your device. (You may see a MAC address or “MISC” before Roswell Cybox appears)
IMPORTANT: Make sure the volume is down on your device before playing music. Give the Cybox a few seconds before pressing “PLAY” on your device in order for the output to sync with the new connection. If you press “PLAY” too early there may be no sound.
You are now ready to listen to your music wirelessly via the Roswell Marine Audio Cybox.

lf you have any questions please call : 1-855-962-WAKE(9253)

Rev. 10-Jul-14

Pg. 3/4

TROUBLESHOOTING: I cannot pair my Cybox.
1. Check to make sure the power wires are fully connected. 2. Check to make sure Bluetooth connectivity is turned-on in your device. 3. Make sure you have paired the Roswell Cybox. 4. Make sure the distance between your device and the Cybox is not greater than 20 feet (6 M). 5. Check to make sure that the Cybox is connected to your audio system.
I get a loud hissing noise from the auxiliary input setting on my head unit.

  1. Make sure the output switch is in the correct position. (See below) 2. Make sure you are connected to the proper output on your Cybox. (See below)
    There is no sound coming from my Audio System. 1. Make sure the 3.5mm plug is fully inserted into to the jack on the Cybox. 2. Confirm the device is paired with the “Roswell Cybox” 3. Make sure you have selected the correct output on your device. 4. Make sure you have the volume control at a suitable listening level.
    Why can’t I control the volume of the Cybox from my iPhone” 3G or 3GS using Bluetooth? Make sure you have downloaded Apple” iOS4 software or later to your iPhone” 3G, 3GS and iPhone” 4.
    For other inquiries please email Roswell Technical support at info@roswellwakeair.com

SWITCHING OUTPUT VOLTAGE
Open the housing of the Cybox by carefully squeezing the lower portion only on the sides and pulling the top portion up.

Switch the output voltage switch to the down position. (This lowers the output voltage from your Cybox to the head unit to a usable level). Replace cover by snapping into place.

I I I
~

Note: The switch’s default position is in the up position.
Note: Only the Stereo 3.5 mm output directly next to this switch is affected. USE THIS OUTPUT ONLY

SPECIFICATIONS · Bluetooth 3.0 · Profiles Supported: aptX®, A2DP and AVRCP · Operates up to 33 feet (10 meters) from your portable device · Output #1: Stereo 3.5MM Jack for Analog Audio Out · Output #2: Stereo 3.5MM Jack for Analog Audio Out · Output #3: Stereo 3.5MM Jack for Analog Audio Out (Switchable for use as an auxiliary input device) · Dimensions of Cybox: 3.5″ x 2.75″ x 7/8″

SAIFETY WARNINGS 0 Do not expose the components of this product to direct moisture. 0 Do not expose the components of this product to excessively high temperatures. 0 Please keep out of reach of children. 0 Please consult your owner’s manual and/or local dealer if issues arise. 0 This product must only be serviced by a qualified technician. 0 Any improper use, alteration, and/or attempt to repair this product will void any e1tpressad limited warranty.

· j ,f you have any questions please call : 1-855-962-WAKE(9253)

Rev. 10-Jul-14

Pg. 4/4

ROSWELL

C920-0300

( FUN ) – CTION
we design it. we build it. you enjoy it.

i-<OSWf L.L.
www.roswellmarine.com
SPEAKER SERIES

REV 29-AUG-16

6.5″/8″ Speaker Assembly Instructions
C920-1600 / C920-1601 / C920-1610 / C920-1611

R1 6.5″ / 8″ Speaker Installation Instructions

www.roswellmarine.com

RO· ,WEL.L.
Welcome to the family.
Thank you for purchasing the best marine speakers in the world. After years of development and testing, we are proud to introduce the R1 Series marine speakers, built to outlast – and outperform every other marine speaker on the market. We at Roswell started a revolution in the wakeboard industry back in 1998, and have since expanded into marine audio and other branches of the marine industry. Even now, nearly 20 years later, we continue to push the boundaries. We are fully committed to going past industry expectations every day to make your boating experience more enjoyable. With the input of our dealers, team riders, and boaters around the world, our goal remains to redefine the marine industry day in and day out. We will not be confined to our desks; we are out on the water testing our full line of products to ensure your days on the water are as hassle-free and enjoyable as possible. The R1 Series is simply the latest iteration of that commitment. Thanks again for choosing Roswell and keep an eye out for more dominating technology throughout the season. If you have any questions about your speakers or questions regarding installation , please contact your authorized Roswell dealer. If you have further questions, please don’t hesitate to contact us directly at (321)-638-1331 OR by emailing support@roswellmarine.zendesk.com.
@————- ROSLUEL.L.

R1 6.5″ / 8″ Speaker Installation Instructions – – – – – A – ——–,

w w w . r o s w e l l m a r i n e .c o m

DESCRIPTION A (overall diameter) B (mounting depth) C (grill height) D (basket diameter) Nominal Impedance Frequency Response Power Sensitivity

6.5″ SPECS

8″SPECS

6.81″ I 173 mm

9.21″ I 234 mm

3″ /76 mm

3.325″ I 85 mm

1.2″ I 30 mm

1.5″ I 38 mm

5.25″ I 133 mm

7.09″ I 180 mm

40

40

60 Hz – 20 kHz +/- 3dB 50 HZ – 20 KHZ +/- 3dB

80 Watts RMS

100 Watts RMS

9odB @1W/1M

9odB @1W/1M

FEATURES:
Plug and play installation Integrated 12 dB/Oct. Crossover Network Integrated flying lead connection for easy installation in tight spaces Integrated RGB LED with controller option Locking trim ring conceals all hardware · Centrex plastic for true marine durability · ASTM Salt Fog Spray Tested – 500 Hours · ASTM UV Tested- 500 Hours · Klippe l-certified for Guaranteed Performance

i-<OSUJf L.L. – – – – – – – – – – – – — 2

R1 6.5″ / 8″ Speaker Installation Instructions
PACKAGE CONTENTS

A x2
R1 Series Speakers

~
B x2
Locking trim rings

~
C x1
Cut out template

www.roswellmarine.com

@

i

@
8

D

E

x8

x1

Hex-head stainless screws

3mm hex-head
bit

PREPARATION
For safety, turn off the audio system and battery switch prior to beginning installation. If your vessel does not have a battery switch, simply disconnect the negative lead from the battery terminal. Use extreme caution before cutting and drilling holes to avoid damaging fuel lines, hydraulic lines, or existing electrical components. If additional wiring is required, we recommend using at least 18 gauge wiring and running all wires prior to installing the speaker. Longer runs may require 16 gauge wire to prevent negative impacts on sound quality. Leave some slack in the wire to allow for easier installation and to prevent tension on the wire. · Avoid running wires near sharp edged surfaces. Never run wires exposed on the deck, protecting the wires behind cover offers the best protection from marine elements. If wires must be routed through metal or fiberglass walls, use rubber grommets to protect the wire. · All wiring should be done by a qualified marine technician. NOTE: Consider how you would Like to use the integrated RGB LED before you begin installation. It can either be hard-wired to one of 7 different colors OR you may purchase an LED controller to allow any combination of colors and patterns.

&

WARNING

&

These speakers are capable of easily producing sound pressure levels (SPU in excess of 100 dB, even in an open-air environment like a boat. Sound pressures at or above these levels can easily cause permanent hearing damage or loss. Be sure to use safe listening practices and protect your ears.

1—————- ROSWEL.L.

R1 6.5″ / 8″ Speaker Installation Instructions
TOOLS REQUIRED

w w w . r o s w e l l m a r i n e .c o m

Dust Mask

Safety Glasses
-====r: I I

Power Drill

Masking Tape Center Punch Pen/ Pencil

Jigsaw/

Wire Strippers / Crimps

Air-saw

c II 17 17 IJ

,Q]===J

1/8″ & 3/8” Drill Bit

Countersink Bit

18 AWG (Red} Heat Shrink Butt Splices (if not using the OEM quick-connect}

INSTRUCTIONS
Follow these illustrated steps to ensure proper installation of your R1 Series Speakers. Note: Required tools for each step are listed in the left column under each steps letter.
Locate a suitable area to mount the speaker in your vessel. Ensure the area is large enough to evenly mount the speaker and grill. Ensure the area behind the mounting area is spacious enough to allow proper fit and air flow.
— – … ….
2″ clearance

Use the cut out template (C} to locate and mark the area for the speakers.

– – ………

.,,,,.

First use the 3/8” drill bit and drill to
start the hole, then cut the mounting hole using jigsaw or air-saw.

NOTE: If cutting through gelcoat/ fiberglass, use extreme caution to avoid cracking the gelcoat. We recommend you tape off the entire area with low-tack masking tape. Cut slowly and carefully.
ROSUJEL.L. __

R1 6.5″ / 8″ Speaker Installation Instructions

www.roswellmarine.com

Remove the trim ring from the speaker first {refer to step G, turning in a counterclockwise direction instead). Place the speaker into the mounting cutout to ensure it will fit. Remove additional material if needed. Once th~ speaker fits properly, align the speaker to the desired orientation and use a center punch or pencil to mark the mounting holes for the screws to secure the speaker. Remove speaker from cutout and drill the holes with a 1/8″ drill bit.



——– — ~ – : .–~

~

– – ~ – \\- — ~

2)

–=i::c:::=J

NOTE: If drilling through fiberglass/gelcoat. be sure to run the drill in
reverse untilyou are through the gelcoat. switch the drill into forward and
finish drilling as normal Then come back with a countersink bit and remove the
gelcoat surrounding the hole. This will help avoid cracking/damaging the
gelcoat around the mounting location.  
Make all connections from the flying lead harness to your in-boat wiring.

flying lead connection  
I  
I

in-boat wiring

If you are not using the OEM quick-connect option, the wires may be cut and
crimped as follows:

1) Cut line–,  
~ µ~

Pin

Wire

Location Color

1

White

2

White/

Black

Function Speaker+ Speaker-

~ ~

2) Strip 5/16″ of wires and connect to boat wiring using 18 AWG (Red) Heat
Shrink Butt Splices

OI:=:1D  
l l : 5115· I butt splice

I I  
in-boat wiring

3

Black LED12V+

4

Red Red LED-

5

Green Green LED –

6

Blue Blue LED-

,____ _ _ _ _ _ _ _ _ _ _ _ _ R.OSWEL.L.

R1 6.5″ / 8″ Speaker Installation Instructions

w w w.r o s w e l l m a r i n e .c o m

Using the included hex-head bit. secure the speaker to the mounting location
using (4) hex-head screws per speaker.

i

c——-

Install the trim ring by orienting the tabs and logo recess in the ring with
the corresponding locations on the grill, fully inserting each tab and then
gently rotating the ring into place by turning it in a clockwise motion.

turn trim clockwise to lock

RECOMMENDED CROSSOVER SETTINGS

6.5″

8″

With Subwoofer  
Without Subwoofer

90-100 Hz depending on 70-80 Hz depending on Listening Preferences listening
preferences  
70-80 Hz depending on 50-60 Hz depending on listening preferences listening
preferences

Gain setting will be dependent on output voltage of the head unit and RMS
power of the amplifier used. Be careful when setting the amplifier and during
listening sessions; burnt voice coils are not covered under warranty.  
i-<OSWI-L.L. _ _ _ _ _ _ _ _ _ _ _ _ __

R1 6.5″ / 8″ Speaker Installation Instructions

w w w.r o s w e l l m a r i n e .c o m

USE AND CARE  
These speakers are built to the highest standards of marine durability.
However; they are still a sensitive piece of electronic equipment. When
cleaning, avoid hosing down the speakers directly. Simply wiping the speaker
down with a damp cloth should be sufficient to ensure years of enjoyment.

ROSWELL LIMITED WARRANTY  
Roswell warrants all new R1 Series Speakers against defects in material and
workmanship for a period of TWO (2) YEARS from the original date of purchase.
This warranty is not transferable and applies only to the original retail
purchaser from an authorized Roswell retailer. Upon inspection by Roswell,
should service be necessary under this warranty for any reason due to
manufacturer defects, Roswell will, at our own discretion, repair or replace
the defective product with new or similar conditioned product at no charge.  
THIS WARRANTY DOES NOT COVER INSTALLATION OR DAMAGE RESULTING FROM ACCIDENT,
MISUSE, ABUSE, IMPROPER WIRING, OPERATION OUTSIDE OF THE MANUFACTURERS
RECOMMENDATIONS OR SPECIFICATIONS, OR AGAINST INSTRUCTIONS IN OWNERS MANUAL.
IN ADDITION, ANY PRODUCT THAT HAS BEEN OPENED, TAMPERED WITH OR MODIFIED, OR
IF ANY SERIAL NUMBERS HAVE BEEN REMOVED, WILL NOT BE COVERED BY ANY PART OF
THE MANUFACTURES WARRANTY.  
All warranty claims must first be made in direct contact with Roswell’s
warranty department. When first contact is made the warranty representative
will issue an RA # to open a claim. All warranty returns should be sent to
Roswell freight prepaid and must be accompanied by proof of purchase (a copy
of original sales receipt>. Direct returns from consumers or non-authorized
retailers will be refused unless specifically authorized by Roswell with a
valid return authorization number (RA#).  
All warranty returns should be packed in the original packaging and must be
accompanied by a copy of the original sales receipt. Product damage during
shipping will not be covered under this warranty. The customer or retailer may
choose to have this damage repaired at the normal “Out of Warranty” repair
cost.  
In no event will Roswell be liable for incidental, consequential, or other
damages resulting from the use of this product. This includes but is not
limited to, damage of hearing, property of person, damage based upon
inconvenience or on loss of use of the product, and to the extent permitted by
law, damages for personal injury.  
This warranty applies to products being sold and used in the United States of
America and Canada. In all other countries please contact your authorized
Roswell representative.  
For warranty and non-warranty repairs, please contact Roswell Global Inc.:  
Phone: 1-[321-638-1331](https://phone.gd/phone/321-638-1331) Email:
warranty@roswellglobal.com

,________________ i-<OSL!Jf L.L.

i-<OSUJI-L.L. RGB RF REMOTE AND CONTROLLER KIT  
USER MANUAL

G R  
a

ROSWEL.L.

Rev 22-Aug-2016

PACKAGE CONTENTS:

· 0  
ROSWELL  
RGB Remote

0

0

I ROSWEL.L.

CID  
CID

CID

CID

RGB RF CONTROLLER

– – – – – iI ii 5~ ~~©(±) ~ ~ ~ ~!~: ~ ~ CE RoHS CIDD

0

0

RGB Controller

ROSWEL.L RGB RF REMOTE AND CONTROLLER KIT  
USER MANUAL  
e  
Manual  
(2) AAA Batteries  
Note: Pull plastic tab from battery compartment before use

Audio Splitter Cable – 3.5 mm audio (female) to (2) 3.5 mm audio (male)

Extendable Auxiliary Cable – 3.5 mm audio (male) to 3.5 mm audio (male)

FEATURES:  
· RF Control – max effective distance 65 ft/20 m · Max. Power output – 432 W ·
Capacitive touch control · 3.5 mm audio input for music synchronization mode ·
20 Standard LED modes · 15 Music synchronized modes  
SPECIFICATIONS:  
· Input voltage: DC12V~24V · Output power: Max 18A · Volume control: 70 dB
range · Remote battery: (2) AAA · Remote standby power consumption: o.o8mW ·
Remote operating power consumption: 2omW

PRODUCT DIMENSIONS:

50mm  
· 0

~ 20  
I mm  
.,…~- -+—r–

105 mm

ROSWELL

98mm

~ 25  
I mm

i~ ROSUJEL.L . iR

B (]DO

\+ <ID

RGB RF CONTROLLER

<ID

86  
mm

G ®0

I ® ~ ~ © – – – – – B ®0

<ID ~ ~ (±) ~; ;~~: ~

CE RoHS + ®..ill

0

0 __l

WIRING DIAGRAM:

r 0

l

Note: Be sure to use the proper

\+ –

=

=

ROSWEL.L.

RGB RF CONTROLLER

=,_g © ::>> CID ~0. <t (±)

12V 216W MAX 24V 432W MAX

CE RoHS

i ~ <ID CID CID ;CID::::: :  
i CID CID CID -CID —

gauge wire (minimum18AWGJ  
RED GREEN BLUE BLACK

TO BOAT

l 0

0 j

TO SPEAKER

…

COMPONENT FUNCTIONS:

0

0

·  
<JD t—–t 0@

ROSL!JEL.L.

RGB RF CONTROLLER

~~ ©  
~Cl. ;~ ;j l~ ‘.i:

– —

1 V 216W MAX  
v 432W MAX

CE RoHS

i~iR  
B <JD  
\+ <ID<ID

G B

<JD<JD

\+ @0

0

0

1 ON/press for 3 seconds to switch to white lighting  
2 OFF  
3 LED color selector 4 Brightness control 5 Speed control  
——————————  
6 Mode control  
7 Music mode switch 8 Sensitivity adjustment  
9 3.5mm audio jack 10 Power input 11 Audio pickup microphone 12 RGB output

PROGRAMMED LED MODES:

Standard Modes

Music Modes

No.

MODE

NOTE

1 Static Mode

7 Colors

– – – —————– ——–

2 7 Color Cycle – – – —————

3 RGB Crossfade – – – —————

-4 –

–

7 Color Crossfade —————

5 Flashing Red – – – —————

6 Flashing Green – – – —————

-7 –

–

Flashing Blue —————

Speed

8 Flashing Yellow

adjustable

– – – —————

9 Flashing Purple  
– – – —————

10 Flashing Cyan  
– – – —————

11 Flashing White – – – —————

12 Red/Green Crossfade  
– – – —————

13 Red/Blue Crossfade – – – —————

14 Green/Blue Crossfade

….

,J

No.

MODE

NOTE

1 Red

2 Green 3 Blue 4 Purple 5 Orange 6 Cyan

Brightness/ Speed  
change with music

7 White

8 7 Color Cycle

9 7 Color Crossfade 10 Flashing Red 11 Flashing Green 12 Flashing Blue 13
Red/Green Crossfade

Color/ Brightness/  
Speed change with  
music

14 Red/Blue Crossfade

15 Green/Blue Crossfade

Mic Mode  
NOTE  
Mode switching is still available  
in MIC mode

SAFETY WARNINGS:  
· Do not expose the components of this product to direct moisture. · Do not
expose the components of this product to excessively high temperatures. ·
Please keep out of reach of children. · Please consult your owner’s manual
and/or local dealer if issues arise. · This product must only be serviced by a
qualified technician. · Any improper use, alteration, and/or attempt to repair
this product will void any expressed  
limited warranty.  
CONTROLLER BATTERIES: · Do not mix alkaline, standard (carbon-zinc) and
rechargeable batteries (Nickel Metal Hydride). · Do not mix old and new
batteries. · Non-rechargeable batteries are not to be recharged. · Exhausted
batteries should be removed immediately and must be recycled or disposed of  
properly according to state or local government ordinances and regulations. ·
The supply terminals are not to be short-circuited. · Only batteries of the
same or equivalent type as recommended are to be used. · Batteries are to be
inserted with the correct polarity. · Do not dispose batteries in a fire –
batteries may leak or explode.

ROSWELL LIMITED WARRANTY  
Roswell warrants all new RGB RF Remote and Controller Kits against defects in
material and workmanship for a period of ONE (1) YEAR from the original date
of purchase. This warranty is not transferable and applies only to the
original retail purchaser from an authorized Roswell retailer. Upon inspection
by Roswell, should service be necessary under this warranty for any reason due
to the manufacturer defect, Roswell will, at our own discretion, repair or
replace the defective product with new or similar conditioned product at no
charge.  
THE WARRANTY DOES NOT COVER INSTALLATION OR DAMAGE RESULTING FROM ACCIDENT,
MISUSE, ABUSE, IMPROPER WIRING, OPERATION OUTSIDE OF THE MANUFACTURERS
RECOMMENDATIONS, OR SPECIFICATIONS, OR AGAINST INSTRUCTION IN OWNERS MANUAL.
IN ADDITION, ANY PRODUCT THAT HAS BEEN OPENED, TAMPERED WITH OR MODIFIED, OR
IF ANY SERIAL NUMBERS HAVE BEEN REMOVED, WILL NOT BE COVERED BY ANY PART OF
THE MANUFACTURERS WARRANTY.  
All warranty claims must first be made in direct contact with Roswell’s
warranty department. When first contact is made the warranty representative
will issue an RA# to open a claim. All warranty returns should be sent to
Roswell freight prepaid and must be accompanied by proof of purchase (a copy
of original sales receipt). Direct returns from consumers or non-authorized
retailers will be refused unless specifically authorized by Roswell with a
valid return authorization number (RA#).  
All warranty returns should be packed in the original packaging and must be
accompanied by a copy of the original sales receipt. Product damage during
shipping will not be covered under this warranty. The customer or retailer may
choose to have this damage repaired at the normal “Out of Warranty” repair
cost.  
In no event will Roswell be liable for incidental. consequential. or other
damages resulting from the use of this product. This includes but is not
limited to, damage of hearing, property of person, damage based upon
inconvenience or on loss of use of the product, and to the extent permitted by
law, damages for personal injury.  
This warranty applies to products being sold and used in the United States of
America and Canada. In all other countries please contact your authorized
Roswell representative.  
For warranty and non-warranty repairs, please contact Roswell:  
Phone: 1-[321-638-1331](https://phone.gd/phone/321-638-1331)  
Email: warranty@roswellglobal.com

www.roswellmarine.com  
Amplifier  
1000.1, 550.2, 650.4, & 900.6 Installation & Usage Instructions

Rev. 190729

Part # C920-1831SD, C920-1832SD, C920-1834SD, C920-1836SD  
Information: info@roswellmarine.com If you have any questions please call :
1-[321-638-1331](https://phone.gd/phone/321-638-1331)

R1 Amplifier Installation Instructions

www.roswellmarine.com

Welcome to the family.  
Thank you for purchasing the best marine amp in the world. After years of
development and testing, we are proud to introduce the R1 Series marine
amplifiers, built to outlast – and outperform – every other marine amp on the
market. We at Roswell started a revolution in the wakeboard industry back in
1998, and have since expanded into marine audio and other branches of the
marine industry. Even now, nearly 20 years later, we continue to push the
boundaries.  
We are fully committed to going past industry expectations every day to make
your boating experience more enjoyable. With the input of our dealers, team
riders, and boaters around the world, our goal remains to redefine the marine
industry day in and day out. We will not be confined to our desks; we are out
on the water testing our full line of products to ensure your days on the
water are as hassle-free and enjoyable as possible.  
The R1 Series is simply the latest iteration of that commitment. Thanks again
for choosing Roswell and keep an eye out for more dominating technology
throughout the season.  
If you have any questions about your speakers or questions regarding
installation, please contact your authorized Roswell dealer. If you have
further questions, please don’t hesitate to contact us directly at
(321)-638-1331 or by emailing info@roswellmarine.com.

C D

Features

· Switchable Differential RCA inputs

· Calibrated Crossover Potentiometers

· 12 dB/oct. Crossover Slopes · Bass boost control (0-18 dB @ 45 Hz)

AB

· Nickel-plated wire terminals

· Conformal coated PCBs

· Full 0-180º phase control (1000.1&550.2 only)

E

Description A (Overall Depth) B (Mounting Bolt Pattern) C (Overall Length) D
(Mounting Bolt Pattern) E (Overall Height)

1000.1, 550.2, 650.4 7.063″ / 179mm 6.180″ / 157mm 11.125″ / 283mm 10.200″/
259mm 1.900″ / 48mm

900.6 7.063″ / 179mm 6.180″ / 157mm 13.661″ / 347mm 12.953″ / 329mm 1.900″ /
48mm

2

R1 Amplifier Installation Instructions 1000.1

www.roswellmarine.com  
See pages 6-7 for amp adjustment  
information

Power/Protect Indicator LED

Power Terminals

Fuses (30 Amp x 3)

Speaker Terminals

RCA inputs/outputs

Differential Input Switch

Remote Gain Module Connection

See pages 6-7 for amp adjustment  
information

Power/Protect Indicator LED

Power Terminals

Fuses (25 Amp x 2)

Speaker

RCA

Differential

Terminals inputs/outputs Input Switch

3

R1 Amplifier Installation Instructions

650.4

www.roswellmarine.com  
See pages 6-7 for amp adjustments  
information

Power/Protect Indicator LED

Power Terminals

Fuses (30 Amp x 2)

Speaker

RCA

Differential

Terminals inputs/outputs Input Switch

Input Select Switch

900.6

See pages 6-7 for amp adjustment  
information

Power/Protect Indicator LED

Power Terminals

Fuses (30 Amp x 3)

Speaker

RCA

Differential

Input

Terminals inputs/outputs Input Switches Select Switch

4

R1 Amp Installation Instructions PACKAGE CONTENTS

www.roswellmarine.com  
TOOLS & SUPPLIES NEEDED

M4 x 15mm

(x1) Amplifier

(x4) Mounting Screws

Wire Strippers Phillips Screw Small Flathead Electrical

& Crimps

Driver Screw Driver Tape

Remote Gain Module (1000.1 Only)

2mm Allen Key 3mm Allen Key 4mm Allen Key

Multimeter (Optional)

4AWG Wire

Inline Fuse

Notes  
Warning  
If you do not have experience with automotive or marine electrical and
mechanical systems please contact a professional installer.  
Paying a qualified installer is almost always cheaper than paying a dealership
to repair your boat.

Please check the suitability of the installation location before you begin. Do
not cut any of the boat’s structure. Pay close attention to what is behind any
bulkheads, panels and carpet. Often the boat manufacturer will hide wires and
cables in the exact location you may wish to install in.

Location of the Amplifier The amplifier must be securely mounted to a solid
surface. Please select a dry location such as in the storage compartment. Do
not mount the amplifier to any area that may have excessive vibration (like
the subwoofer box), under any cup holder drain lines, or under ballast
drain/vent fittings that may leak water. Position the amplifier in an area
that receives sufficient airflow and mount it vertically or completely flat
for optimal heat dissipation.

Supplying Enough Power The R1 Series amplifiers are capable of significant
output. In order to achieve this it is critical that the amplifiers 12 Volt
wiring is adequate to provide the necessary power to the amplifier. We
recommend using 4AWG wire for all power and ground connections. Be sure to
fuse the power wire appropriately for the amount of current being drawn.

The Ground The ground wire should be connected directly to the battery of your
boat. Remember, the ground must carry the same high current as the positive
wire.

RCA Cables The R1 Series amplifiers feature differential RCA inputs for
maximum noise rejection. However, it is still a good idea to follow best
practices to minimize the amount of interference in the signal chain. To
reduce the risk of noise, run all signal cables away from any power supplying
wires.

Protection Indicator This amplifier is equipped with an advanced protection
system. If for any reason this unit goes into protection mode it will flash a
solid single red LED light found on the control end of the amplifier. In most
cases, the amp will automatically recover once the issue causing the protect
mode is corrected.

Installing Multiple Amplifiers Roswell offers a stacking spacer for use with
R1 Amps (C920-1830). These allow you to stack amplifiers on top of each other
securely. Roswell recommends stacking a maximum of four amplifiers when done
on a flat surface or two amplifiers when mounted on a vertical surface. It may
be necessary to provide more airflow for more amplifiers as more amps will
generate more heat.

5

R1 Amp Installation Instructions

www.roswellmarine.com

Sensitivity Due to the wide range of head unit output configurations all RMA
amplifiers have an adjustable input sensitivity. The level is not a volume
control. It is used to properly set the ouput of the amplifier based on the
output voltage of the source unit, and to ensure the speakers are receiving
clean power at an appropriate level. With the sensitivity turned up, the
amplifier will reach maximum output at a lower volume setting on the source
unit.  
There is no correct sensitivity setting suitable for all applications as head
unit preamp outputs vary. If you are unsure on adjusting this settings,
consult an audio installation professional.  
Crossover Controls A crossover is a circuit that filters unwanted frequencies.
A tweeter can easily be blown by bass frequencies if they are not filtered
out. A subwoofer will not sound natural if it is playing mid range
frequencies. Careful adjustment is needed to ensure that all speakers are
playing the right frequencies and that they are left with no gaps in the
frequency response.  
The R1 Series amplifiers feature calibrated potentiometers in the crossover
section which allows for very precise adjustment of the filter frequency. The
900.6 and 650.4 amplifiers feature a single crossover. Simply select whether
you would like the crossover to be a low-pass or high-pass, and adjust
accordingly. The 1000.1 also features a Subsonic (infrasonic) filter, which is
explained in detail below.  
Full – Allows the full range of frequencies to pass through.  
HPF (High-Pass Filter) – A high-pass filter allows high frequency signals to
pass through while reducing all signals lower than the cutoff frequency
setting on its dial.  
HPF Frequency Response Curve  
(illustrates crossover set at 90Hz)

Amplitude (dB)

60 70 80 90 100 110 120 130 140 150 Frequency (Hz)  
LPF (Low-Pass Filter) – A low-pass filter allows low frequency signals to pass
through while reducing all signals higher than the cutoff frequency setting on
its dial.  
LPF Frequency Response Curve  
(illustrates crossover set at 80Hz)

Amplitude (dB)

10 20 30 40 50 60 70 80 90 100 Frequency (Hz)  
Subsonic (1000.1 & 550.2 only) – A Subsonic, or infrasonic, filter is
essentially a high-pass filter dedicated to removing the lowest frequencies.
This allows you to remove unwanted frequencies in order to protect your
subwoofer from excess power, or to prevent it from unloading when it is in a
ported enclosure or free-aired application. In most cases this filter should
be set at around 30 Hz (12:00 position on the dial).  
Phase Control (1000.1 & 550.2 only) – The Phase control allows you to fine-
tune the output of the amplifier in order to ensure that the sound from the
subwoofer is in-phase with the sound with the rest of the audio system
maximize the bass output. Depending on your subwoofer mounting location this
may not need to be adjusted. If you are unsure on how to properly adjust this
setting, leave it alone.  
Bass Boost All of the RMA amplifiers have an adjustable bass boost from 0-18
dB @ 45 Hz. Adjust the Bass Boost carefully – the response on the power output
is tremendous!  
Remote Gain Control The 1000.1 Amplifier includes a remote gain control module
that can be plugged into the amplifier to allow easy reduction of the gain
setting without accessing the amplifier.  
6

R1 Amp Installation Instructions

www.roswellmarine.com

RCA Inputs All R1 amplifiers feature switchable differential RCA inputs to
maximize noise rejection.  
Input Select Switch The 900.6 and 650.4 amplifiers feature an input selection
switch that will allow you to set which RCA inputs feed signal to the
amplifier. You can choose a dedicated RCA input for each channel, or to have
one pair of RCAs to supply the signal to all channels. The 900.6 also allows
for 4 channel input to control all 6 outputs. This allows you to group
channels together to easily interface with head units that feature zone
control, or to use with our Dual Zone Volume Control. NOTE: Set this switch
before tuning your amplifier.  
RCA Line Out The 1000.1, 550.2, and 650.4 amplifiers have line out connections
that allow you to connect multiple amplifiers together. The 550.2 and 650.4
line outs supply a full range stereo signal. The 1000.1 line out supplies a
mono signal as it is designed to provide signal to additional subwoofer
amplifiers.  
Speaker Outputs All R1 amplifiers are equipped with a block style terminal for
speaker connection. Make these connections carefully and neatly. Strip your
wire back 5/8″ (16mm) and twist the exposed leads. Using a 2mm Allen wrench,
loosen the terminal set screws far enough to allow the wire to fit. Insert
them into the appropriate spot on the block terminal. Make sure that there are
no loose or frayed strands of wire sticking out. If a wire comes in contact
with another wire, the amplifier will go into protection mode. After
tightening the terminal set screws, verify your wires are secured in place by
gently pulling on them.  
Impedance

The 900.6 and 650.4 Amplifiers are 2 stable on each channel, meaning that up
to two 4 speakers can be wired in parallel per channel. When bridging channels
the speaker must have a nominal impedance of at least 4. Attempting to run
speakers below 4 when bridging channels could result in damage to the
amplifier and will void the warranty.

The 1000.1 Amplifier is 1 stable, meaning that up to four 4 subwoofers can be
connected to the amplifier simultaneously. If you are unsure about impedance
matching or series vs. parallel wiring, consult an audio installation
professional.

Technical Specifications

Parameter Continuous power:  
@ 4 @ 2 @ 1 Bridged power Frequency Response (+/- 1dB) Input Sensitivity
Crossover Frequency Range Subsonic Filter Phase Control Bass EQ

1000.1  
400W 675W 1000W N/A 10Hz-400Hz 0.2-10.0V 30Hz-300Hz 10Hz-55Hz 0-180º
Continuous 0-18dB @ 45Hz

550.2

650.4

900.6

165W x2

100W x4

100W x6

275W x2

165W x4

165W x6

N/A

N/A

N/A

4: 550W x1

4: 300W x2

4: 300W x3

10Hz-25 kHz

10Hz-25 kHz

10Hz-25 kHz

0.2-10.0V

0.2-10.0V

0.2-10.0V

30Hz-300Hz 10Hz-55Hz 0-180º Continuous

30Hz-300Hz Auto 6dB/oct. @ 30Hz in HPF Mode  
N/A

30Hz-300Hz Auto 6dB/oct. @ 30Hz in HPF Mode  
N/A

0-18dB @ 45Hz

0-18dB @ 45Hz

0-18dB @ 45Hz

7

R1 Amp Installation Instructions  
1000.1  
Amplifier Application Examples  
Single Sub Output

www.roswellmarine.com

Double Sub Output

Subwoofer 1-8

Subwoofer 2-8 Subwoofer 2-8  
Quadruple Sub Output

Subwoofer 4-8 Subwoofer 4-8  
Control Panel  
Note: Settings shown are for illustrative purposes only and are NOT standard
or recommended settings

Subwoofer 4-8 Subwoofer 4-8

8

R1 Amp Installation Instructions  
650.4  
Amplifier Application Examples  
4- Channel Output

www.roswellmarine.com

Speaker 2-8  
3- Channel Output

Speaker 2-8

Speaker 2-8

Speaker 2-8

Speaker 2-8  
2- Channel Output

Speaker 2-8 Subwoofer/Speaker 4

Control Panel  
Note: Settings shown are for illustrative purposes only and are NOT standard
or recommended settings

Speaker 4-8

Speaker 4-8

9

R1 Amp Installation Instructions  
900.6  
Amplifier Application Examples  
6- Channel Output

www.roswellmarine.com

Speaker 2-8

Speaker 2-8

5- Channel Output

Speaker 2-8

Speaker 2-8

Speaker 2-8

Speaker 2-8

Speaker 2-8

Speaker 2-8

4- Channel Output

Speaker 2-8

Speaker 2-8

Speaker 4-8

Speaker 2-8

Speaker 2-8

Speaker 4-8

Speaker 4-8

10

R1 Amp Installation Instructions  
900.6 continued  
Amplifier Application Examples  
6- Channel Output

www.roswellmarine.com

Control Panel

Speaker 4-8

Speaker 4-8

Speaker 4-8

Note: Settings shown are for illustrative purposes only and are NOT standard
or recommended settings

11

R1 Amp Installation Instructions  
A Disconnect the positive cable from the boat battery. Tape up the end so it
is isolated from the battery.

www.roswellmarine.com

B

Run a 4 AWG wire from the battery to the amplifier. Plan this part of the
installation carefully. This cable will carry a very high current . If it
should short to any metal and is not properly fused it could catch fire.

+-

C

To protect the power wires, connect an in-line fuse holder to the power cable
as close to the battery as possible. If one amplifier is being used, refer to
the table below for recommended fuse rating. If two or more amplifiers are
being used, verify the fuse and wire are capable of handling the total current
load of all amplifiers connected. The amplifiers themselves are internally
fused and do not require additional protection.

Amp

1000.1

900.6

x1

650.4

Fuse 100A 100A 60A

D

Run the black 4 AWG ground wire directly to the negative (-12V) pole on the
battery. This wire should handle the load in the previous step and be as short
as possible.

+-

E

Wire your speakers and route wires to your amp mounting location. Using the
allen key, connect the speaker wires to the amplifier. Be sure to note the
wire polarity.

+-

2mm (650.4 & 900.6)  
4mm (1000.1)

12

R1 Amp Installation Instructions

F

Run a wire from the head unit remote turn-on wire (typically blue or blue w/
white stripe) to the “REM” terminal of the amplifier.

www.roswellmarine.com

G

Turn on the amplifier to verify it is wired correctly and does not go into
protection mode. The power LED should turn solid blue after a few seconds.

To Head unit or switch

Lights up

You must now set the controls on the amplifier. This is the most important
part of amplifier installation and should be completed by a trained audio
professional.  
H Remove control panel cover with a 3mm allen wrench. Adjust amplifier
settings to provide appropriate power to the speakers. Replace cover when
complete.

3mm

13

R1 Amp Installation Instructions

Roswell Limited Warranty

www.roswellmarine.com

Roswell warrants all new R1 Series Amplifiers against defects in material and
workmanship for a period of TWO (2) YEARS from the original date of purchase.
This warranty is not transferable and applies only to the original retail
purchaser from an authorized Roswell retailer. Upon inspection by Roswell,
should service be necessary under this warranty for any reason due to
manufacturer defects, Roswell will, at our own discretion, repair or replace
the defective product with new or similar conditioned product at no charge.  
THIS WARRANTY DOES NOT COVER INSTALLATION OR DAMAGE RESULTING FROM ACCIDENT,
MISUSE, ABUSE, IMPROPER WIRING, COSMETIC DAMAGE DUE TO NORMAL WEAR AND TEAR,
EXPOSURE TO CHEMICALS OR HARSH ENVIRONMENTS, OPERATION OUTSIDE OF THE
MANUFACTURERS RECOMMENDATIONS OR SPECIFICATIONS, OR AGAINST INSTRUCTIONS IN
OWNERS MANUAL. IN ADDITION, ANY PRODUCT THAT HAS BEEN OPENED, TAMPERED WITH OR
MODIFIED, OR IF ANY SERIAL NUMBERS HAVE BEEN REMOVED, WILL NOT BE COVERED BY
ANY PART OF THE MANUFACTURES WARRANTY.  
All warranty claims must first be made in direct contact with Roswell’s
warranty department. When first contact is made the warranty representative
will issue an RA # to open a claim. All warranty returns should be sent to
Roswell freight prepaid and must be accompanied by proof of purchase (a copy
of original sales receipt). Direct returns from consumers or non-authorized
retailers will be refused unless specifically authorized by Roswell with a
valid return authorization number (RA#).  
All warranty returns should be packed in the original packaging and must be
accompanied by a copy of the original sales receipt. Product damage during
shipping will not be covered under this warranty. The customer or retailer may
choose to have this damage repaired at the normal “Out of Warranty” repair
cost.  
In no event will Roswell be liable for incidental, consequential, or other
damages resulting from the use of this product. This includes but is not
limited to, damage of hearing, property or person, damage based upon
inconvenience or on loss of use of the product, and to the extent permitted by
law, damages for personal injury.  
This warranty applies to products being sold and used in the United States of
America and Canada. In all other countries please contact your authorized
Roswell representative.  
For warranty and non-warranty repairs, please contact Roswell Marine Inc.  
Phone: 1-[321-638-1331](https://phone.gd/phone/321-638-1331) Email:
warranty@roswellmarine.com

14

R1 Amp Installation Instructions

www.roswellmarine.com

Cooling & Airflow Warning

AMPLIFIER MAY BECOME VERY HOT DURING NORMAL OPERATION  
Your new Roswell Marine Audio amplifer possesses exceptional efficiency and
thermal management. However, it is possible that, if mounted in a confined
space and/or high temperature environment, it may become extremely hot during
periods of extended use. Special attention must be given during the
installation process to optimize cooling efficiency. An unobstructed airflow
around the amplifier’s heat sink is required to enable proper cooling. For
optimal performance Roswell recommends mounting the amplifier as follows:

Vertical Mount

Flat Mount

Mounting the amplifier in a position that does not enable proper cooling will
affect the performance of the unit and is strongly discouraged.

In addition to proper mounting ensure that no items are in direct contact with
the amplifier Life vests, wet suits, towels, coolers, and other like items
must be kept away from amplifier.

Roswell Marine is not liable for damage resulting from improper mounting
and/or negligent use of this product. Notes

15





#### References

  * [ SwellMarine.com is for sale | HugeDomains](http://swellmarine.com "SwellMarine.com is for sale | HugeDomains")
  * [ Roswell Marine | Wake Towers, Marine Audio, & Board Racks](http://www.roswellmarine.com "Roswell Marine | Wake Towers, Marine Audio, & Board Racks")
  * [ Zendesk: The Complete Customer Service Solution](http://zendesk.com "Zendesk: The Complete Customer Service Solution")

## Read User Manual Online (PDF format)

[Read User Manual Online (PDF format)&nbsp;&nbsp;&gt;&gt;](/pdf/2345-next-post-next-postroswell-862063-bat-wh-ronda-63-in-acrylic-flatbottom-soaking-bathtub-instructions)

## Download This Manual (PDF format)

[Download this manual&nbsp;&nbsp;&gt;&gt;](https://manuals.plus/m/0268c93a6cd865374381b4f2c219abf9b6b2ee9b525f635b3a7f8e1a2ace33bd_optim.pdf)

Related Manuals