KFI PRODUCTS 102040 Winch Mount User Manual

June 13, 2024
KFi PRODUCTS

KFI PRODUCTS 102040 Winch Mount

Honda Talon – Winch Mount

Item Quantity Description
1 1 Winch Mount
2 1 Fairlead Mount
3 2 Bumper Tube Bracket
4 1 Contactor Mount
5 1 Mini-Rocker Hardware Kit (HK-031)
6.1 2 M6 – 1.00 x 20 Hex Flange Bolt
6.2 2 M6 – 1.00 Hex Flange Nylock Nut
6.3 2 M8 – 1.25 x 60 Hex Flange Bolt (black)
6.4 6 M8 – 1.25 x 20 Hex Flange Bolt
6.5 8 M8 – 1.25 Hex Flange Nylock Nut

Installation Instructions:

Note: Make sure all of the hardware needed to complete this mount is in the package. Read through and understand the instructions before installing.

Step 1:
Remove the front bumper by removing hardware (A) and (B) on both the passenger and driver side.

Step 2:
Set the winch mount plate (1) into place and insert one of the top OEM bolts (A) removed in step one through the bumper and the mount to hold the mount in place. Bolt the bottom of the mount to the bumper fascia using bolt (6.4) and nut (6.5).

Step 3:
Set the fairlead mount (2) into the bumper and insert the two bumper tube brackets (3) over the square tube frame on the bumper and into the fairlead bracket. Loosely fasten using bolts (6.3) and nut (6.5).

Step 4:
Fasten the winch mount (1) to the fairlead mount (2) using bolts (6.4) and nuts (6.5). Make sure the winch mount (1) is centered with the square frame tube of the bumper before tightening.

Step 5:
Mount your winch upside down with the winch motor on the driver side of the vehicle and the clutch on the passenger side using hardware supplied with the winch.

Step 6:
Reinstall the bumper using the OEM hardware (A) and (B) removed from step one. Tighten all hardware evenly.

Wiring Instructions:

Step 1:
Remove the hood and the top plastic cover by removing the plastic push rivets and bolts labeled (C).

Step 2:
Bolt the contactor bracket (4) provided with your winch mount to the OEM contactor location. Bolt the contactor supplied with your winch to the contactor bracket (4).

Step 3:
Using the pre-ran OEM positive (+) and negative (-) battery cables, wire your contactor and switches per your wiring instructions provided in the winch manual. Connect the red positive (+) battery cable to the battery located under the rear driver’s side fender. The black negative (-) battery cable is already grounded.

HONDA TALON

Winch Mount PART #102040

OVERVIEW

ITEM    QTY                  DESCRIPTION                   ITEM    QTY DESCRIPTION

1| 1| Winch Mount| 6| 1| Hardware Kit (HK-198)
2| 1| Fairlead Mount| 6.1| 2| M6 – 1.00 x 20 Hex Flange Bolt
3| 2| Bumper Tube Bracket| 6.2| 2| M6 – 1.00 Hex Flange Nylock Nut
4| 1| Contactor Mount| 6.3| 2| M8 – 1.25 x 60 Hex Flange Bolt (black)
5| 1| Mini-Rocker Hardware Kit (HK-031)
 | 6.4| 6| M8 – 1.25 x 20 Hex Flange Bolt
6.5| 8| M8 – 1.25 Hex Flange Nylock Nut

INSTALLATION INSTRUCTIONS

Note: Make sure all of the hardware needed to complete this mount is in the package. Read through and understand the instructions before installing.

  1. Remove front bumper by removing hardware (A) and (B) on both the passenger and driver side shown in Figure 1. Note: do not discard hardware as it will be reused in a later step. Note: some later models will only have two plastic push pins on the inside of the front bumper to remove the plastics.

  2. Set winch mount plate (1) into place and insert one of the top OEM bolts (A) removed in step one through the bumper and the mount to hold the mount in place as shown in Figure 2. Bolt bottom of mount to the bumper fascia using bolt (6.4) and nut (6.5) as shown in Figure 2.

  3. Set fairlead mount (2) into the bumper and insert the two bumper tube brackets (3) over the square tube frame on the bumper and into the fairlead bracket as shown in Figure 3. Loosely fasten using bolts (6.3) and nut (6.5)

  4. Fasten the winch mount (1) to the fairlead mount (2) using bolts (6.4) and nuts (6.5) as shown in Figure 2.
    Note: be sure that the winch mount (1) is centered with the square frame tube of the bumper before tightening.

  5. Mount your winch upside down with the winch motor on the driver side of the vehicle and the clutch on the passenger side using hardware supplied with the winch as shown in Figure 4. Note: see Figure 5 for winch bolt hole locations for standard and wide winches.

  6. Reinstall the bumper using the OEM hardware (A) and (B) removed from step one as shown in Figure 6. Note: some bolts may need to be loosened to fit the winch mount and bumper back on to the machine, then tightened once bumper is installed.

  7. Tighten all hardware evenly.

WIRING INSTRUCTIONS

  1. Remove the hood and the top plastic cover by removing the plastic push rivets and bolts labeled (C) as shown in Figure 1.
  2. Bolt the contactor bracket (4) provided with your winch mount to the OEM contactor location as shown in Figure 2 & 3 using two of the contactor bolts supplied with your winch. Note: the holes in the OEM contactor location may need to be drilled out to fit the bolts through. Bolt the contactor supplied with your winch to the contactor bracket (4) as shown in Figure 3.
  3. Using the pre-ran OEM positive (+) and negative (-) battery cables shown in Figure 2 wire your contactor and switches per your wiring instructions provided in the winch manual. Note: you will need to connect the red positive (+) battery cable to the battery located under the rear driver’s side fender as shown in Figure 4. The black negative (-) battery cable is already grounded.

Keyed 12V Accessory Wire

Located near the OEM contactor location is a blue plug attached to the frame tube of the machine with a green and a white/black wire as shown in Figure 2 & 5.

  1. Connect the red positive (+) wire from your rocker switch and/or hand remote to the white/black wire on the OEM plug.

©2022 Copyright Kappers Fabricating, Inc. All rights reserved

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

KFi PRODUCTS User Manuals

Related Manuals