KFi PRODUCTS 106270 Plow Fairlead Pulley Brackets Instruction Manual
- June 12, 2024
- KFi PRODUCTS
Table of Contents
KFi PRODUCTS 106270 Plow Fairlead Pulley Brackets
PART LIST
Pulley Part #106270 & 106465
| Item # | Qty. | Description |
|---|---|---|
| 1 | 1 | Fairlead Pulley Bracket |
| 2 | 1 | Synthetic Plow Roller Pulley |
| 3 | 1 | HK-138 |
| 3.1 | 2 | 3/8”-16 x .75 Hex Bolt |
| 3.2 | 1 | 3/8”-16 x 1-1/2 Carriage Bolt |
| 3.3 | 2 | 3/8” Flat Washer |
| 3.4 | 2 | 3/8” Lock Washer |
| 3.5 | 2 | 3/8”-16 Hex Jam Nut |
| 3.6 | 1 | 3/8”-16 Hex Flange Nylock Nut |
| 3.7 | 2 | 1.25 x .78 x .04 Spacer (not used) |
| 3.8 | 1 | Plow Pulley Bushing (not used) |
Note: Make sure all hardware needed to complete this mount is in the package. Thoroughly read through and understand the instructions before installing.
INSTALLATION INSTRUCTIONS:
-
Place rope over pulley in the position shown in figure 2. This position is the only one that should be used with synthetic rope.
Note : Keep in mind that your rope needs to clear your fairlead bracket.
-
Place rope over pulley and install to Pulley Bracket using the 1 1/2” Carriage Bolt (3.2) and Flange Nut (3.6) as shown in Figure 1.
-
Loosely install 3/8” bolt (3.1), washer (3.3), lock washer (3.4), and nut (3.5) through fairlead bracket and pulley bracket as shown in figures 1 and 3. Slots have been cut into the brackets to adjust for clearance of plastic on the machine.
-
Once desired position is found, tighten down all nuts. Pulley should not be able to rotate once tightened.
Note : Make sure the rope is as close to 90 degrees from the ground as you can get it. Most plows come with 3 or more hook points for winches that are offset from the center of the machine.
USING PLOW PULLEY ON PUSH TUBES
The plow fairlead pulley can also be attached to the push tubes in multiple configurations. In this case, the rope will go from the roller fairlead to the pulley (located on the push tubes) and then back up to a bumper or solid anchor point. View next page for information on how to attach the Plow Fairlead Pulley to the push tubes.
Note : Standard fairlead pulley required for all push tube applications.
THIS MOUNT RECOMMENDS A PLOW PULLEY
SYNTHETIC ROPE PLOW FAIRLEAD PULLEY
- ALUMINUM ROLLER
- STANDARD OR WIDE
STEEL CABLE PLOW FAIRLEAD PULLEY
- RECOMMEND A PULLEYATTHE WTNCH AS WELLAS PUSH TUBE. VIEW EXAMPLE BELOW.
- STEEL ROLLER
- STANDARD OR WIDE
12″ SOFT LOOP STRAP WRAPS AROUND BUMPER OR SOLID ANCHOR POINT THE ABOVE PULLEY.
WHY USE A PULLEY?
WHEN THE WINCH FAIRLEAD AND PLOW PIN POINT ARE CLOSE TO EACH OTHER, IT CREATES A SHALLO\V LIFTING ANGLE. BY ADDING A PULLEY, YOU ARE CHANGING THE WINCH ANGLE TO A MORE VERTICAL LIFTING POSITION. THIS WILL PROVIDE LESS STRAIN ON THE WINCH AND ENTIRE PLOW SYSTEM.
POSSIBLE POSITIONS
STANDARD FAJRLEAD PULLEY REQUIRED FOR A LL PUSH TUBE APPLICATIONS
LIFT HOOK POSITIONED FOR EXTRA SUPPORT
CUSTOMER SUPPORT
©2021 Copyright Kappers Fabricating, Inc. All rights reserved
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>