PortKeys BM7IIDS Rugged 7 Inch Touchscreen Monitor User Manual
- June 13, 2024
- PortKeys
Table of Contents
PortKeys BM7IIDS Rugged 7 Inch Touchscreen Monitor User Manual
Service Hotline： 18820958861
Email： [email protected]
Website： www.portkeys.com
Company Address：1406, 14th Floor, Block D, Building 3,
Cloud Park, Longgang District, Shenzhen, Guangdong, China
Factory Address： 2nd Floor, Building A, Jingjiang Industrial Park,
NO.101, Shangwei Road, Longhua District, Shenzhen,Guangdong, China
Product Information 1.1
Product Introduction
Product Information 1.2
Packing List
BM7 II DS Monitor X1
Micro USB Flash Drive X1
Safety Box X1
Threaded DC Power Cable X1
Customer Feedback Card X1
Product Information 1.3
Basic Parameters
Product Information 1.4
Signal Specifications
Supported input resolution and frame rate
HDMI Signal
1920×[email protected],24Hz,25Hz,29.97Hz,30Hz,50Hz,59.94Hz,60Hz
1920×[email protected],24Hz,25Hz,29.97Hz,30Hz
1920×1080i@50Hz,59.94Hz,60Hz
1280×720p@50Hz,59.94Hz,60Hz
720×576p&720×576i@50Hz
720×480p&720×480i@50Hz,59.94Hz,60Hz
Supported input/output resolution and frame rate
SDI Signal
1920×1080p@50fps,59.94fps,60fps
1920×1080p@50Hz,59.94Hz,60Hz YUV422
1920×[email protected],24Hz,25Hz,29.94Hz,30Hz YUV444/YUV422
1920×[email protected],24Hz,25Hz,29.97Hz,30Hz YUV444/YUV422
1920×1080i@50Hz,59.94Hz,60Hz YUV444/YUV422
1280×720p@50Hz,59.94Hz,60Hz YUV444/YUV422
Warnings 6.1
Warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation i subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
6. Set Up Photos-15C
I can not find the blow 1GHz test setup photo and AC line conducted emission
setup photo.
Please provide.
For AC line conducted emission：
“If the EUT normally receives power from another device that in turn connects
to the public utility ac power lines, measurements shall be made on that
device with the EUT in operation to demonstrate that the device continues to
comply with the appropriate limits while providing the EUT with power. If the
EUT is operated only from internal or dedicated batteries, with no provisions
for connection to the public utility ac power lines (600 VAC or less) to
operate the EUT (such as an adapter), then ac power-line conducted
measurements are not required.”
The earphone normally receives power from charge box that in turn connects to the public utility AC power lines.so line conducted emission need to tested.
7. BLE-test report
For AC line conducted emission：
The earphone normally receives power from charge box that in turn connects to
the public utility AC power lines.so line conducted emission need to tested.
8. A3-TZ2009001675-E2 BT
1).product name is incorrect.
Product Description
Trade Mark ………………..:TECNO
Product name ……………: Mobile Phone
Model No …………………..:A3
Standards ………………….: FCC Rules and Regulations Part 15 Subpart C Section 15.247 ANSI C63.10;2013
2).For AC line conducted emission：
The earphone normally receives power from charge box that in turn connects to
the public utility AC power lines.so line conducted emission need to tested.