TECNO PHANTOM V Fold Smartphone User Manual

June 13, 2024
TECNO

TECNO PHANTOM V Fold Smartphone

Product Information:

The PHANTOM V Fold is a mobile phone that features a foldable design. It comes with various components and specifications, including:

  • CTP+LCM 7.85AMOLED display
  • 3 F HSG ASM A
  • 5 FCAM FRAME
  • 7 FCAM 16M
  • 9 CAM 50M
  • 11 REAR FRAME
  • 13 FLASH DECO
  • 15 RCAM DECO
  • 17 50M CL CAM DECO
  • 19 BAT COVER
  • 21 D-D SCREW M1.4D24.5L25
  • 23 SCREW M1.2D23L13
  • 25 HING ROTATE
  • 27 F HSG ASM B
  • 29 PCBA SUB-LCM
  • 31 REC
  • 33 OFF-SCREEN LP FPC
  • 35 LP FRAME
  • 37 STEEL B1
  • 39 MAIN LCM DECO B
  • 41 CTP+LCM 6.42AMOLED
  • 43 STEEL B2
  • 45 SIM PLUG ASM
  • 47 BOT SPK FPC
  • 49 BOT SPK
  • 51 CARD HOLDER ASM
  • and more…

Additionally, the phone has a front camera, volume control keys, power key with a side fingerprint sensor, and NFC functionality.

Product Usage Instructions

SIM/SD Card Installation:

  1. Power off the mobile phone.
  2. Refer to the provided picture for SIM/SD card installation.

Charging the Phone:

You can charge your device using a charger or by connecting it to the computer using a USB cable that comes with the phone. It is important to follow these guidelines:

  • Use only TECNO charger and cables. Other chargers or cables may damage the device and void your phone warranty.

FCC Caution:

The PHANTOM V Fold complies with Part 15 of the FCC Rules. Please be aware of the following:

  • This device should not cause harmful interference.
  • This device must accept any interference received, including interference that may cause undesired operation.
  • Any changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment.

For specific absorption rate (SAR) information, this mobile phone meets the government’s requirements.

The HiOS operating system runs on AndroidTM OS, which is a trademark of Google LLC.

Explosion diagram specification

1 CTP+LCM 7.85AMOLED 2 MAIN LCM DECO A
3 F HSG ASM A 4 PCBA MB
5 FCAM FRAME 6 FLASH FPC
7 FCAM 16M 8 CAM 50M CL
9 CAM 50M 10 CAM 13M AF
11 REAR FRAME 12 NFC
13 FLASH DECO 14 SIDEKEY FRAME
15 RCAM DECO 16 RCAM LENS
17 50M CL CAM DECO 18 50M CL CAM LENS
19 BAT COVER 20 SCREW M1.4D25L25
21 D-D SCREW M1.4D24.5L25 22 SCREW M1.4D25L35
23 SCREW M1.2D23L13 24 HING ROTATE DECO
25 HING ROTATE 26 OVER-AXIS FPC-1
27 F HSG ASM B 28 REC FRAME
29 PCBA SUB-LCM 30 FCAM 32M
31 REC 32 TOP SPK
33 OFF-SCREEN LP FPC 34 REC FPC
35 LP FRAME 36 TOP BOX ASM
37 STEEL B1 38 SUB LCM BTB STEEL
39 MAIN LCM DECO B 40 SCREW M1.4D25L28
41 CTP+LCM 6.42AMOLED 42 BAT 2300MAH
43 STEEL B2 44 BOT BOX ASM
45 SIM PLUG ASM 46 SUB-LCM PCBA TO SIM PCBA FPC
47 BOT SPK FPC 48 MOTO
49 BOT SPK 50 PCBA SIM
51 CARD HOLDER ASM 52 OVER-AXIS FPC-2
53 SCREW M1.4D25L20 54 USB PCBA FRAME
--- --- --- ---
55 ANT PCBA FRAME 56 USB RUBBER
57 SIDEKEY ASM 58 STEEL A1
59 STEEL A2 60 BAT 2700MAH
61 RF CABLE LINE-3 62 RF CABLE LINE-1
63 RF CABLE LINE-2 64 MB FPC
65 MAIN PCBA TO ANT PCBA FPC 66 SIDEKEY FPC
67 FP 68 PCBA USB
69 PCBA ANT  

Know your phone

  1. Front camera
  2. Volume + key
  3. Volume – key
  4. Power key & side fingerprint sensor
  5. NFC

SIM/SD card installation

  1. Power off mobile.
  2. Refer to the following picture for SIM / SD card installation.

Charging the phone

You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).
Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.

FCC Caution

Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Information to user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information:

This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: AD10 (FCC ID: 2ADYY-AD10) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.751W/kg and when properly worn on the body is1.196W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that does not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

HiOS runs on AndroidTM OS.
Android is a trademark of Google LLC.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals