zowieTek LiveV200 High Definition Bonding Live Streaming Encoder User Guide
- June 12, 2024
- zowieTek
Table of Contents
High Definition
Bonding Live Streaming Encoder
Quick Start Guide
Zowietek Electronics, Ltd.
Revision K2.0-A2.5x
Release 2020-07-28
Product 30411-XXX
Connections
| 
---|---
No.| Name| Icon| Description
---|---|---|---
1| Line In| | Stereo audio input.
2| SDI Input| | Connect up to SDI signal.
3| SDI Loop Out| | Connect a SDI cable from this connector to a monitor or
projector.
4| SMA Connector| | Connect to Internal 4G LTE antenna.
5| DC Power Connector| | Plug the power supply in here. The port requires a
15V DC power source (center-positive).
6| SIM card slot| | Built-in 4G, Plug the NANO SIM card in here.
7| HDMI Input| | Connects HDMI and DVI signals (using an adapter).
8| RJ-45 Ethernet| | Ethernet network port.
9| WIFI Connector| | Connect to WIFI antenna.
10| USB Connector| | Connect to USB WIFI Dongle.
11| 3.5mm Audio Output| | For audio confidence monitoring. Plays the audio for
the currently visible channel
12| TF Card Slot| | Plug the TF card in here.
13| HDMI Loop Out| | Connect a HDMI cable from this connector to a monitor or
projector.
14| Hot Shoe Mount| | Mount LiveV200 to camera
a| RED Power Button| | Press to turn on encoder.
Press and hold more than 5 seconds to turn off.
b| Stream LED Button| | Press to start/stop a streaming.
Solid Red – Streaming is live and online.
Flashing red — No network connection, try to go live. Light Off – Streaming is
offline
c| QR Code Gray Button| | Press to Display/Hide QR Code on LCD Screen
Note:| LiveV200 has an internal rechargeable battery, so please keep it
turning off and charging until fully charged when users first use it. This is
required only for the first use. When battery is fully charged, Stream Button
LED will go out
Screen Display
If LAN, WIFI, 4G network are connected, the screen will display all of the
network information. 
| No | Description |
|---|---|
| 1 | The IP address of LAN network |
| 2 | The IP address of wireless network |
| 3 | HDMI signal input, |
Display Resolution and Frame Rate of HDMI inputs
4| SDI signal input
Display No Signal when the no SDI input or SDI connection fail
5| Display LAN when the LAN connection is successful
Display uplink speed of LAN when the LiveV200 using LAN as streaming network
6| Display the WIFI SSID when the WIFI connection is successful
Display 0 kb when the WIFI is not involved in streaming
7| Display the Operator when the Built-in 4G connection is successful
Display 0 kb when the Built-in 4G is not involved in streaming
8| Display the Operator when the External 4G connection is successful
Display 0 kb when the External 4G is not involved in streaming
9| Streaming Mode: Normal (Single) or Bonding
10| Streaming Icon and Video streaming bit rate
The Streaming Icon disappears and display 0 kb when the streaming is offline
11| Battery Level and Battery percentage
12| Time
13| Power Off
14| Hide / Display desktop
Hide / Display text and icons on the LCD screen
15| Lock / Unlock screen
16| Video Collage
Customize layout, SDI and HDMI dual-channel seamless handover, Picture in
picture
17| Menu Setting
Quick Start Guide
Please follow following steps for quick connection guidance of the encoder.
Step 1. Make the Power Adapter plugged.
Step 2. Press the RED Power button on the left of encoder to turn on
the system.
Step 3. Turn on your camera or video source and connect the output to
corresponding connection of the encoder.
Step 4. Connect encoder to Network.
Encoder allows you to connect multiple ways. Find brief descriptions of these
modes below.
LAN mode
Connect RJ-45 Ethernet cable from the LAN port to the router. The IP address (
) of the encoder will show on the LCD once connected to LAN or WIFI, users can
enter the IP address into the address bar of the web browser on PC or phone,
and then the encoder Web Control User Interface will be shown as follows. In
this example, the IP address is “192.168.1.118”.
Step 5. After
clicking the “RTMP Param” option on the left column of the web control UI,
please fill in “RTMP Address” and click “Confirm” button to apply the setting.
RTMP Address
Step1. Please login your video streaming provider account.
Step2. Find rtmp url or server url usually in ingestion area
Step3. Find stream key in the same section
Step4. Copy, paste and combine rtmp url and stream key to RTMP Address
setting section of encoder.
NOTE:
Don’t forget click the confirm button to apply and save the setting.
WIFI mode
There are four ways to connect WIFI. Make sure that WIFI Antenna is connect to
encoder, device will connect to the WIFI automatically.
- On LCD, please switch the “WIFI” button is “Open”, then the user can press the “Scan” button, find WIFI name and connect it.
- Or press the “Other” button, then input WIFI SSID and Password to connect a network, and don’t forget to click “√” in the top right corner to save and apply it.
- On Web, click “Network”==>”Built-in WIFI”, after clicking the “scan” button, find WIFI name and connect it.
- After clicking the “Manual Input” button, please enter WIFI “SSID” and “Password” to connect a network.
If connect success, the information about the WIFI will be update after clicked “refresh” button.
Built-in 4G
Plug SIM card and connect antenna to encoder, this page provides users to
choose whether to enable built-in 4G network. The default 4G option is
selected to be enabled. 
APN setting： After clicking the pen
icon in the red mark box on above picture, turn off “APN Auto” and fill in
“APN”. Please ask your network operator or search online to find the APN of
your 4G LTE network. When the APN setting is changed, don’t forget to restart
the device to take effect. 
External 4G
Plug USB 4G Dongle into the encoder, device will connect to 4G net
automatically. E8372H and MF833V 4G LTE dongles recommend.
NOTE:
- SIM don’t support hot-plugging, so turn off the unit before plug.
- When WIFI connection setting is complete, don’t need to set up again unless users want to connect to another WIFI.
Bonding mode
- On LCD, after clicking “Live”, you can turn on/off network bonding mode.
- Another way, after clicking the “RTMP Param” option on the left column of the web control UI, the “Model” is selected as “Bonding”, the device will bonding multiple connected networks as stream network. Furthermore, the encoder supports up to 9 RTMP Address streaming simultaneously in this model.
Last, please fill in “RTMP Address” and click “Confirm” button to apply the setting.
Mobile-Phone Backend Setting
If you are not carrying or inconvenient for using your computer, you can also choose to configure your encoder by using your phone’s backend settings. Please press “QR Code” button on the top of the device to show the QR code at first, in another way, you also can find QR Code in “Menu/Setting—QR Code”.
LiveV210’s QR code is at the back of the encoder. Please scan the QR code with
your mobile phone and enter the user interface as shown below. If you don’t
have an account yet, please click “Create account” at the bottom of the
picture to create your own account. 
After logging in to your personal account
and entering the interface as shown below, at first, please click on “active
now” to bind the device to your account. Next time you can find your device in
the list of personal devices.
Once you registered your account, you can
also login your account at xx.livevbond.com on PC
to set encoder. xx could be in, eu, us, au, cn etc. depends on your encoder
country or area.
NOTE:
- Make sure connect a RJ45 network cable to the LAN port of encoder.
- Make sure the encoder connected to Internet before go ahead at the first time.
Find LAN IP address for LiveV210
LAN IP address of LiveV210 can be found here in red box, then you can visit
this IP in browser for advanced feature settings once having it. If LAN
[Connected] does not show in this screen, that means the encoder does not
connect to LAN or the LAN is not online. Please check connection and Internet.
If you want to
know more, you can download the user manual at this link:
https://www.zowietek.com/uploads/PortableBondedEncoder/UserManual3.1.pdf
www.zowietek.com
ZOWIETEK ELECTRONICS, LTD.
Address: 2218 HuNan Road, West Wing 17F01, Pudong,
Shanghai 201204 P.R.China
Tel: +86-21-5027 7371; +86-21-5027 7372| Email:
Sales: sales@zowietek.com
Marketing: marketing@zowietek.com
Support: support@zowietek.com
---|---
SALES IN USA
Security Products International
Sales: us@zowietek.com| Global Aggregation
Server Website:
India: in.livevbond.com
Europe: eu.livevbond.com
US: us.livevbond.com
Australia: au.livevbond.com
China: cn.livevbond.com
MADE IN CHINA
Documents / Resources
|
zowieTek LiveV200 High Definition Bonding Live Streaming
Encoder
[pdf] User Guide
LiveV200, LiveV330-350, Live310, Live210, LiveV200 High Definition Bonding
Live Streaming Encoder, High Definition Bonding Live Streaming Encoder,
Bonding Live Streaming Encoder, Live Streaming Encoder, Encoder
---|---